About the journal
International Journal of Advanced Design and Manufacturing Technology (ADMT), is an open access double-blind peer reviewed publication which is published by Islamic Azad University Isfahan Branch concerned with new concepts and findings in areas related to mechanical engineering, either empirical or theoretical . The ADMT is a quarterly publication, which publishes original research papers in journal scopes. This journal is following of Committee on Publication Ethics (COPE) and complies with the highest ethical standards in accordance with ethical laws. All submitted manuscripts are checked for similarity through a trustworthy software named iThenticate to be assured about its originality and then rigorously peer-reviewed by the international expert reviewers (Read More...).
Journal of Advanced Design and Manufacturing Technology (ADMT) is indexed in ProQuest, Ebsco, ISC, COPERNICUS, Google Scholar, J-gate, SID, Sherpa Romeo, EZB(Electronic Journal Library) and Researchbib.
-
Open Access Article
1 - Nonlinear Wheel Slip Control of Electric Vehicles with In-Wheel BLDC Motors
Majid Majidi * ، Pouyan AhmadizadehIssue 2 , Vol. 18 , Summer 2025 -
Open Access Article
2 - Comparison And Verification of The Results of The GTN Damage Model and The Porous Metal Plasticity Model in The Square Deep Drawing Process
Navid Givianpour ، Hamed Deilami Azodi * ، Shahrouz Yousefzadeh ، Siamak MazdakIssue 2 , Vol. 18 , Summer 2025 -
Open Access Article
3 - Experimental Analysis and Statistical Prediction of Tissue Temperature in High-Speed Cortical Bone Drilling Process
Mehdi Safari ، Vahid Tahmasbi ، Jalal Joudaki * ، Mojtaba ZolfaghariIssue 2 , Vol. 18 , Summer 2025 -
Open Access Article
4 - Study of Overload Effects on Increased Fatigue Life by Meshless Local Petrov-Galerkin Method and Experimental Test
Ali Moarrefzadeh *Issue 2 , Vol. 18 , Summer 2025 -
Open Access Article
5 - Optimization of Mechanical and Process Parameters for Enhanced Energy Conversion Efficiency in the Aluminum-Air Batteries
Mohammad Saadat ، Saeid Kheradmand *Issue 2 , Vol. 18 , Summer 2025 -
Open Access Article
6 - Effect of Damping and Apparent Resistance on Energy Harvesting from Piezoelectric Beam using Dynamic Stiffness Method
Majid Jabbari * ، Bijan Ahmadi ، Sajad HamediIssue 2 , Vol. 18 , Summer 2025 -
Open Access Article
7 - On the Analysis of Two-Dimensional Functionally Graded Rotating Thick Hollow Cylinder
Mostafa Omidi Bidgoli * ، Mohammad Hosseini ، Ali FataIssue 2 , Vol. 18 , Summer 2025
-
Open Access Article
1 - Investigating the Effect of Separation Speed and Image Cross-Section Geometry on The Separation Force in DLP Method using FEP and PP Polymer Membranes
Siavash Moayedi Manizani * ، Jamal Zamani ، Mohammad Salehi ، Mohammad Taghi shayestehIssue 3 , Vol. 16 , Autumn 2023 -
Open Access Article
2 - Forecasting Operational Parameters of a Solar Space Heating System using a Novel Multistage Artificial Neural Network
Farnaz Jamadi * ، Behnam JamaliIssue 2 , Vol. 11 , Spring 2024 -
Open Access Article
3 - Dynamic Response of FGM Plates Under Blast Load
reza azarafza * ، puya pirali ، Ali Davar ، majid ghadimiIssue 4 , Vol. 16 , Winter 2023 -
Open Access Article
4 - Investigation of The Effect of Notch Tip Radius on Fracture Energy of Charpy in 7075 Aluminium Alloy
Ali Hossein zadeh * ، Mohammad Reza Maraki ، Mohsen SadidiIssue 2 , Vol. 13 , Spring 2024 -
Open Access Article
5 - The Effect of Type and Location of a Phase Change Material (PCM) Layer in a Building Wall on Energy Consumption using Numerical Simulation
Arezoo Soleimani Dashtaki ، Afshin Ahmadi Nadooshan * ، Afshin AbediIssue 4 , Vol. 12 , Autumn 2024 -
Open Access Article
6 - Fabrication, Testing and Analysis of Composite Lattice Panels Under Three-Point Bending Load
Mahdi Farhadi ، Ali Davar * ، Mohsen Heydari Beni ، Jafar Eskandari JamIssue 1 , Vol. 17 , Spring 2024 -
Open Access Article
7 - Investigation of the AFM Indenter’s Geometry Effect On Micro/Nano Biological Cells’ Indentation
Yousef Habibi Sooha ، Moharam Habibnejad * ، Zahra RastegarIssue 4 , Vol. 13 , Autumn 2024 -
Open Access Article
8 - Microstructure Investigation and Mechanical Properties of Resistance Upset Butt Welded Ti-6Al-4V Alloy
Mahmood Sharifitabar *Issue 3 , Vol. 13 , Summer 2024 -
Open Access Article
9 - A Study on The Effects of Different Pad Materials on Brake System Performance of a High-Capacity Elevator by FEM Simulation
Mohammad Sajjad Mahdieh * ، Farshad Nazari ، Ali Riyadh KhairullahIssue 4 , Vol. 16 , Winter 2023 -
Open Access Article
10 - Investigation of Compressive Stresses of Stainless Steel 316L Diamond Lattice Structures Under the Effect of Spherical Connections Produced by SLM Additive Manufacturing
Behnam Ahmadi Roozbahani ، AliAkbar Lotfi Neyestanak *Issue 4 , Vol. 16 , Winter 2023