List of Articles

• Open Access Article
  • Abstract Page
  • Full-Text
  
  1 - Experimental Investigation on Process Parameters of Dissimilar Double-Layered Wire Produced by Modified Friction Stir Extrusion Process
  Masoud Yavari Nouri S. M. Hossein Seyedkashi Moosa Sajed
  10.30495/admt.2021.1911339.1220
• Open Access Article
  • Abstract Page
  • Full-Text
  
  2 - Investigating the Effect of Electrical Discharge Process Input Parameters on Mechanical Properties of Aluminum Surface
  Hadi Eivazi bagheri Hamid Gorji Mohammad Reza Shabgard mohamad Bakhshi-Jooybari
  10.30495/admt.2021.1919424.1236
• Open Access Article
  • Abstract Page
  • Full-Text
  
  3 - Evaluation of Fatigue Behavior and Surface Characteristics of Novel Machining Process: Rotary Chemical Machining (RCM)
  Pooya Bahrami Ali Khoshanjam Abdolhamid Azizi
  10.30495/admt.2021.1921815.1247
• Open Access Article
  • Abstract Page
  • Full-Text
  
  4 - Influence of Al2O3 Additive on Mechanical Properties of Wollastonite Glass-Ceramics
  Monavvar Rahimi Babak Sadeghi Maryam Kargar Razi
  10.30495/admt.2021.1913578.1226
• Open Access Article
  • Abstract Page
  • Full-Text
  
  5 - Removing Residual Stress and Increasing Fatigue Life by Ultrasonic Method
  Ali Moarefzadeh
  10.30495/admt.2021.1907388.1213
• Open Access Article
  • Abstract Page
  • Full-Text
  
  6 - A Comprehensive Study on the Effects of the Boundary Conditions on the Elastic Buckling Capacity of a Perforated Plate
  Sadegh Ghorbanhosseini Saeed Yaghoubi Mohammad Reza Bahrambeigi
  10.30495/admt.2021.1914605.1227
• Open Access Article
  • Abstract Page
  • Full-Text
  
  7 - Design and Optimization of Gasketed-Plate Heat Exchanger using Bees Algorithm
  Navid Bozorgan Ashkan Ghafouri Ehsanolah Assareh Seyed Mohammad Safieddin Ardebili
  10.30495/admt.2021.1907203.1211
• Open Access Article
  • Abstract Page
  • Full-Text
  
  8 - Increasing the Fundamental Frequency of the Cantilever Rotating Beam by Placing the Intermediate Elastic Support with Minimum Stiffness at the Optimum Point Based on the Courant’s Maximum–Minimum Theorem using Finite-Element Analysis Software
  Mehdi Asgarikia Farshad Kakavand Hasan Seidi
  10.30495/admt.2021.1917477.1232
• Open Access Article
  • Abstract Page
  • Full-Text
  
  9 - The Effect of Process Parameters and Tool Geometrical Parameters on the Tool Peak Temperature in Machining Process
  Maziar Mahdipour Jalilian Amir Ghiasvand Hasan Kheradmandan
  10.30495/admt.2021.1914924.1228
• Open Access Article
  • Abstract Page
  • Full-Text
  
  10 - Numerical Investigation of the Grid Geometry Effect on the Modal Response and Buckling of Grid-Stiffened Composite Conical Structure
  Mohammad Reza Zamani Mohsen Zaretabar Hossein Parsa Mohsen Heydari Beni
  10.30495/admt.2021.1921748.1245