Investigating the Effect of Electrical Discharge Process Input Parameters on Mechanical Properties of Aluminum Surface

Subject Areas : advanced manufacturing technology

Hadi  Eivazi bagheri ¹ (Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran)
Hamid  Gorji ² (Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran)
Mohammad Reza  Shabgard ³ (Department of Mechanical Engineering, Tabriz University, Tabriz, Iran)
mohamad  Bakhshi-Jooybari ⁴ (Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran)

Received: 2021-01-01 Accepted : 2021-04-09 Published : 2021-09-01

Keywords: Aluminum, Micro Cracks, Surface Yield Strength, Electrical discharge Process,

Abstract :

One of the important parameters in electrical discharge machining is the presence of micro cracks on the workpiece surface (recast layer). Therefore, the aim of this study was to investigate the possibility of increasing the mechanical properties of aluminum surface by alloying elements (copper and nickel) diffusion to the recast layer and thus removing surface micro cracks. For this purpose, pulse on time and pulse current in with and without ultrasonic vibration have been considered as input parameters and the presence of surface micro cracks has been investigated using microscopic images. Also, the yield stress of the surface layer was calculated using the surface micro hardness. Based on the obtain results, surface without micro cracks has been created on the aluminum surface due to the diffusion of copper and nickel into the workpiece surface which increased aluminum surface yield strength from 90MPa to 280MPa without ultrasonic vibrations and to 310MPa while applying ultrasonic vibrations. In other words, ultrasonic vibrations cause an average of 20% increase in surface layer yield strength. In addition, according to the wear test, in the case of using ultrasonic vibration, improving the mechanical properties of the surface has caused thinner grooves on the aluminum surface.

References:

• Jiru, G., Sankar, M. R., Dixit, U. S., Surface Alloying of Aluminum with Copper using Co2 Laser, Laser based Manufacturing, 2015, pp. 107-116.


• Mageough, J. A., Advanced Methods of Machining, Chapman and Hall, 1987.


• Lee, H. T., Tai, T. Y., Relationship Between EDM Parameters and Surface Crack Formation, Journal of Materials Processing Technology, Vol. 142, 2003, pp. 676-683.


• Simao, J., Lee, H. G, Aspinwall, D. K., Dewes, R. C., and Aspinwall, E. M., Workpiece Surface Modification Using Electrical Discharge Machining, International Journal of Machine Tools and Manufacture, Vol. 43, 2003, pp. 121-128.


• Tiryakioğlu1, M., Robinson, J. S., Salazar-Guapuriche, M. A., and Zhao, Y. Y., Hardness-Strength Relationships in the Aluminum Alloy, Material Science and Engineering, Vol. 631, 2015, pp. 196-200.


• Jiru, W. G., Sankar, M. R., and Dixit, U. S., Laser Surface Alloying of Copper, Manganese and Magnesium with Pure Aluminum Substrate, Journal of Materials Engineering and performance, 2016, doi:10.1007/s1166-016-1922-x.


• Mabahali, L. A., Pitiyana, S. L., and Sacks, N., Laser Surface Alloying of Aluminum with Ni and SiC Powders, Materials and Manufacturing Processes, Vol. 25, No. 12, 2010, pp.1397-1403.


• Lin, H., Kuralay, S., and Uan, J., Microstructural and Corrosion Characteristics of Iron-Silicon Alloyed Layer on 5083 Al Alloy by Electrical Discharge Alloying Processing, Materials Transactions, Vol. 52, No. 3, 2011, pp. 514–520.


• Shabgard, M. R., Khosrozadeh, B., Study on the Effect of Ultrasonic Assisted Electrical Discharge Machining Process On Residual Stress and Hardness of Ti-6Al-4V Alloy, Modares Mechanical Engineering Journal, Vol. 16, No. 8, 2016, pp. 169-176 (in Persian).


• Shabgard, M. R., Tavanaei, H., and Khosrozadeh, B., Study the Effect of Electrical DI Scharge Machining (EDM) on Residual Stress and Corrosion Resistance of Ti-6Al-4V Alloy, Modares Mechanical Engineering Journal, Vol. 18, No. 3, 2018, pp. 171-178 (in Persian).


• Eivazi Bagheri, H., Gorji, H., Shabgard, M. R., Nourouzi, S., Experimental Study On the Surface Modification by Electrical Discharge Process, Journal of Applied and Computational Mechanics, Vol. 5, No. 2, 2019, pp. 100-108.


• Tuysserkani, H., Principles of Materials Science, Isfahan University of Technology, Iran, 2004, (in Persian).


• Chen, Y., Lin, Y., Surface Modifications of Al-Zn-Mg Alloy Using Combined EDM with Ultrasonic Machining and Addition of TiC Particles into Dielectric, Journal of Materials Processing Technology, Vol. 209, 2009, pp. 4343-4350.


• Kong, W., Cang, D., and Song, H., Effects of Ultrasonic Treatment During the Solidification Process on the Structure Formation of Low Carbon Steel, Materials Transactions, Vol. 52, No. 9, 2011, pp. 1844-1847.