Design and Optimization of Gasketed-Plate Heat Exchanger using Bees Algorithm

Subject Areas : optimization and simulation

Navid  Bozorgan ¹ (Department of Mechanical Engineering, Dezful Branch, Islamic Azad University, Dezful, Iran)
Ashkan  Ghafouri ² (Department of Mechanical Engineering, Ahvaz Branch, Islamic Azad University, Ahvaz, Iran)
Ehsanolah  Assareh ³ (Department of Mechanical Engineering, Dezful Branch, Islamic Azad University, Dezful, Iran)
Seyed Mohammad  Safieddin Ardebili ⁴ (Department of Mechanical Engineering, Dezful Branch, Islamic Azad University, Dezful, Iran, and Department of Biosystems Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran)

Received: 2020-08-18 Accepted : 2020-12-20 Published : 2021-09-01

Keywords: Heat transfer enhancement, pressure drop, Design and Optimization, Gasketed-Plate Heat Exchanger, Bees Algorithm,

Abstract :

In the present study, the hydraulic-thermal design and optimization of a gasketed-plate heat exchanger (GPHE) with an objective function of heat exchanger performance index (the amount of transferred heat exchange to pumping power ratio) is carried out. This process is made by considering 6 design parameters (the port diameter, plate thickness, the enlargement factor, the compressed plate pack length, the horizontal port distance, and the vertical port distance) and through the Bees Algorithm (BA). The present study achieved three solution sets for the design parameters by investigating the sensitivity of the design parameters heeded in the optimization of the GPHE. The design parameters in these three optimal solution sets were opted for in such a way that heat transfer increased by 41.6%, 34.55%, and 20.7%, and pressure drop decreased by 11.89%, 27%, and 83%, respectively.

References:

• Wang, C., Cui, Z., Yu, H., Chen, K., and Wang, J., Intelligent Optimization Design of Shell and Helically Coiled Tube Heat Exchanger Based On Genetic Algorithm, International Journal of Heat and Mass Transfer, Vol. 159, 2020. DOI: 10.1016/j.ijheatmasstransfer. 2020.120140.


• Zhicheng, Y., Lijun, W., Zhaokuo, Y., and Haowen, L., Shape Optimization of Welded Plate Heat Exchangers Based On Grey Correlation Theory, Applied Thermal Engineering, Vol. 123, 2017, pp. 761-769. DOI: 10.1016/j.appltherm.aleng.2017.05.005.


• Maghsoudi, P., Sadeghi, S., and Gorgani, H. H., Comparative Study and Multi-Objective Optimization of Plate-Fin Recuperators Applied in 200 kW Microturbines Based On Non-Dominated Sorting and Normalization Method Considering Recuperator Effectiveness, Exergy Efficiency and Total Cost, International Journal of Thermal Sciences, Vol. 124, 2018, pp. 50-67, DOI: 10.1016/j.ijthermalsci.2017.10.001.


• Hasanpour, A., Farhadi, M., and Sedighi, K., Intensification of Heat Exchangers Performance by Modified and Optimized Twisted Tapes, Chemical Engineering & Processing: Process Intensification, Vol. 120, 2017, pp. 276-285, DOI: 10.1016/j.cep.2017.07.026.


• Zhang, P., Ma, T., Li, W. D., Ma, G. Y., and Wang, Q. W., Design and Optimization of a Novel High Temperature Heat Exchanger for Waste Heat Cascade Recovery from Exhaust Flue Gases, Energy, Vol. 160, 2018, pp. 3-18, DOI: 10.1016/j.energy.2018.06.216.


• Wang, S., Jian, G., Xiao, J., Wen, J., Zhang, Z., and Tu, J., Fluid-Thermal-Structural Analysis and Structural Optimization of Spiral-Wound Heat Exchanger, International Communications in Heat and Mass Transfer, Vol. 95, 2018, pp. 42-52. DOI: 10.1016/j.ich.eatmasstransfer.2018.03.027.


• Wang, C., Zhengyu, C., Hongmei, Y., Kai, C., and Jianli, W., Intelligent Optimization Design of Shell and Helically Coiled Tube Heat Exchanger Based On Genetic Algorithm, International Journal of Heat and Mass Transfer, Vol. 159, 2020. DOI: 10.1016/j.ijheatmasstransfer.2020. 120140.


• Yin, Q., Du, W. J., Ji, X. L., and Cheng, L., Optimization Design and Economic Analyses of Heat Recovery Exchangers On Rotary Kilns, Applied Energy, Vol. 180, 2016, pp. 743-756. DOI: 10.1016/j.apenergy.2016.07.042.


• Momeni, S. M., Salehi, G., and Eshagh Nimvari, M., Modeling and Thermoeconomic Optimization of Marine Diesel Charge Air Cooler, Energy, Vol. 162, 2018, pp. 753-763. DOI: 10.1016/j.energy.2018.08.092.


• Wu, J., Liu, S., and Wang, M., Process Calculation Method and Optimization of the Spiral-Wound Heat Exchanger with Bilateral Phase Change, Applied Thermal Engineering, Vol. 134, 2018, pp. 360-368. DOI: 1016/j.applthermaleng.2018.01.128.


• Omolayo Petinrin, M., Bello-Ochende, T., Adebukola Dare, A., and Olanrewaju Oyewola, M., Entropy Generation Minimisation of Shell-and-Tube Heat Exchanger in Crude Oil Preheat Train using Firefly Algorithm, Applied Thermal Engineering, 145, 2018, pp. 264-276. DOI: 10.1016/j.applthermaleng.2018.09.045.


• Mohanty, D. K., Application of Firefly Algorithm for Design Optimization of a Shell and Tube Heat Exchanger from Economic Point of View, International Journal of Thermal Sciences, Vol. 102, 2016, pp. 228-238. DOI: 10.1016/j.ijthermalsci.2015.12.002.


• Pu, L., Qi, D., Xu, L., and Li, Y., Optimization on the Performance of Ground Heat Exchangers for GSHP Using Kriging Model Based on MOGA, Applied Thermal Engineering, Vol. 118, 2017, pp. 480-489. DOI: 1016/j.applthermaleng.2017.02.114.


• Mirzaei, M., Hajabdollahi, H., Fadakar, H., Multi-Objective Optimization of Shell-And-Tube Heat Exchanger by Constructal Theory, Applied Thermal Engineering, Vol. 125, 2017, pp. 9-19. DOI:1016/j.applthermal. Eng.2017.06.137.


• Zarea, H., Kashkooli, F. M., Mehryan, A. M., Saffarian, M. R., and Beherghani, E. N., Optimal Design of Plate-Fin Heat Exchangers by a Bees Algorithm, Applied Thermal Engineering, Vol. 69, 2014, pp. 267-277. DOI: 10.1016/j.applthermaleng.2013.11.042.


• Etghani, M., Hosseini Baboli, S. A., Numerical Investigation and Optimization of Heat Transfer and Exergy Loss in Shell and Helical Tube Heat Exchanger, Applied Thermal Engineering, Vol. 121, 2017, pp. 294-301. DOI: 1016/j.applthermaleng.2017.04.074.


• Yang, H., Wen, J., Wang, S., Li, Y., Thermal Design and Optimization of Plate-Fin Heat Exchangers Based Global Sensitivity Analysis and NSGA-II, Applied Thermal Engineering, Vol. 136, 2018, pp. 444-453. DOI: 10.1016/j.applthermaleng.2018.03.035.


• Pham, D. T., Ghanbarzadeh, A., Koc, E., Otri, S., Rahim, S., and Zaidi, M., The Bees Algorithm. Technical Note, Manufacturing Engineering Centre, Cardiff University, UK, 2005.


• Kakac, S., Liu, H., Heat Exchangers Selection, Rating, and Thermal Design, Boca Raton London New York Washington, D. C., 2002.


• Cao, E., Heat Transfer in Process Engineering, New York: McGraw-Hill, 2010.