• XML

    isc pubmed crossref medra doaj doaj
  • List of Articles


      • Open Access Article

        1 - Three Dimensional Free Vibration of FGM Circular Plates Using Semi-Analytical Method
        MohamadMehdi Najafzadeh Payman Shoghi
        In this research three-dimensional free vibration analysis of functionally graded circular plate with various boundary conditions is achieved. A semi-analytical method, which makes use of the state space method and the one-dimensional differential quadrature method, is More
        In this research three-dimensional free vibration analysis of functionally graded circular plate with various boundary conditions is achieved. A semi-analytical method, which makes use of the state space method and the one-dimensional differential quadrature method, is used to obtain the vibration frequencies and dynamic responses of circular plates. Numerical results are given to demonstrate the accuracy and superiority of the presented method. The numerical results are compared with the existing numerical solutions and good agreement is displayed .Using the semi-analytical method, the analytical solution in the thickness direction is given and an effective approximate solution in the radial direction is obtained by selecting fewer discrete points. Manuscript profile
      • Open Access Article

        2 - Measuring Vibration in the Air Slide Tables of Ultra Precision Machines With the Different Number of Air Pockets
        Mehrdad Vahdati Sayed AliReza Rasouli
        Vibration in the air slide tables of ultra precision machines prevents gaining accuracies within nanometer level. In this work, dissimilar types of internal vibration including small vibrations and pneumatic hammers have been tested and some measures have been offered t More
        Vibration in the air slide tables of ultra precision machines prevents gaining accuracies within nanometer level. In this work, dissimilar types of internal vibration including small vibrations and pneumatic hammers have been tested and some measures have been offered to reduce their effects. This paper has also proceeded to the vibration tests on the air slide tables built with different number of air cell (air pocket). Comparison in critical pressures, self-excited vibration analysis, and predicting the behavior of contrastive points of the table (that a tool or a work piece might get installed on it) are the results of experiments by different variations of air pressures. Manuscript profile
      • Open Access Article

        3 - Fluctuating Flow Characteristics and Heat Transfer from Two in-Tandem Square Cylinders
        Amin Etminan
        In this paper, the flow around bluff bodies with different cross sections and determination of forces acts on them are investigated.This paper presents the results of a numerical study on the flow characteristics and heat transfer over two equal square cylinders in a ta More
        In this paper, the flow around bluff bodies with different cross sections and determination of forces acts on them are investigated.This paper presents the results of a numerical study on the flow characteristics and heat transfer over two equal square cylinders in a tandem arrangement. Spacing between the cylinders is 5 widths of the cylinder and the Reynolds number ranges from 1 to 200, Pr=0.71. Both steady and unsteady incompressible laminar flow in the two-dimensional regime are studied. A study of the effects of spatial resolution and blockage on the results is provided. In this paper, the instantaneous and mean streamlines, vorticity and isotherm patterns for different Reynolds numbers are presented and discussed. Also the global quantities such as pressure and viscous drag coefficients, Strouhal number and Nusselt number are determined and discussed for various Reynolds numbers. Manuscript profile
      • Open Access Article

        4 - Determining Maximum Dynamic Load Carrying Capacity of Cable Robots Between Two End Points of Workspace
        Moharam Habibnejad Khaled Najafi Mehdi Bamdad
        In this paper, according to high load capacity and rather large workspace characteristics of cable driven robots (CDRs), maximum dynamic load carrying capacity (DLCC) between two given end points in the workspace along with optimal trajectory is obtained. In order to fi More
        In this paper, according to high load capacity and rather large workspace characteristics of cable driven robots (CDRs), maximum dynamic load carrying capacity (DLCC) between two given end points in the workspace along with optimal trajectory is obtained. In order to find DLCC of CDRs, joint actuator torque and workspace of the robot constraints concerning to non-negative tension in cables are considered. The problem is formulated as a trajectory optimization problem, which is fundamentally a constrained nonlinear optimization problem. Then the iterative linear programming (ILP) method is used to solve the optimization problem. Finally, a numerical example involving a 6 DOF CDR is presented and results are discussed. Manuscript profile
      • Open Access Article

        5 - Numerical Study of Effective Parameters on Cold Rolling of Tri-layers Al/St/Al and Cu/Al/Cu
        Mohamad Sedighi Edvin Golestanian Mahmoud Honarpishe
        In this paper, the rolling force and reduction ratio have been investigated in multilayer strip rolling. For this purpose, two different set of multilayers have been selected which are Al/St/Al and Cu/Al/Cu layouts. At first, the validation of the numerical analysis was More
        In this paper, the rolling force and reduction ratio have been investigated in multilayer strip rolling. For this purpose, two different set of multilayers have been selected which are Al/St/Al and Cu/Al/Cu layouts. At first, the validation of the numerical analysis was performed by using an experimental test. After validation of the numerical results, two set of multilayer layouts were simulated and the total rolling force and the reduction ratio of each layer have been obtained. Finally, the effect of friction factor between the strip and the roll on the rolling force and reduction ratio has been studied. The results show that stiffness of each layer and the thickness ratio (clad to core) have significant effects on the layers thickness reduction. Also by increasing the friction factor between roll and strip, the clad thickness reduction is decreased and the core thickness reduction and rolling force will be increased. Manuscript profile
      • Open Access Article

        6 - Simulation of Laminar and Turbulent Flow around Tube Bundles and Effect of Rynolds Number
        Mansour Talebi
        When flow passes over the tube bundles, energy of flow transfers to the tubes. The Fluid Induced Vibrations (FIV) imposed on the tubes is one of the important problems in analyzing the tube bundles and causes several problems. In this work, first, laminar flow around ci More
        When flow passes over the tube bundles, energy of flow transfers to the tubes. The Fluid Induced Vibrations (FIV) imposed on the tubes is one of the important problems in analyzing the tube bundles and causes several problems. In this work, first, laminar flow around circular cylinder asymmetrically in a channel is simulated. The Reynolds number is 20 and 100. The lift forces to tube are not zero. Also flow over tube bundle with twenty-four rods is simulated and flow characteristics are obtained. In this problem, the Reynolds Number is 50 to 40000 and the pressure contours, streamlines and velocity vectors are obtained. At last, turbulent flow over a tube bundle with special boundary condition is calculated. For turbulent modeling, the Large Eddy Simulation Method with Smagorinsky and Mix model and the Parallel programming method is used. Flow pattern and characteristics are obtained. Numerical results show a very good agreement with experimental results and reveal interesting flow behavior which is applicable to steam generators of nuclear power plants. Manuscript profile
      • Open Access Article

        7 - Free Vibration Analysis of S-FGM-Coated and S-FGM-Undercoated Plates with Classical Boundary Conditions
        Reza Amininejad AliReza Mohajerani AliReza Samsami Shahab Amininejad
        This work presents free vibration analysis of laminated rectangular plates with classical boundary conditions based on the classical plate theory (CPT). The first involves an S-FGM plate with different boundary conditions. Then involves a two-layer plate in which an S-F More
        This work presents free vibration analysis of laminated rectangular plates with classical boundary conditions based on the classical plate theory (CPT). The first involves an S-FGM plate with different boundary conditions. Then involves a two-layer plate in which an S-FGM layer is coated on a homogeneous substrate with classical boundary conditions, simply called an S-FGM-coated plate; the other involves a three-layer plate in which an S-FGM employed for inter-medium layer and different homogeneous materials are in top and bottom layers with classical boundary conditions; this is called an S-FGM-undercoated plate. The Young’s modulus of FGM plates is assumed to vary in the thickness direction and the poisson's ratio remain constant throughout the FGM plate. The material gradations in FGM portion of laminate structures follow sigmoid functions, therefore these plates are called S-FGM. For multi-layer structures, the calculations of the quantities defined herein become complex, therefore, a method is used to easily and efficiently calculating them in this investigation. The results are first compared with the ABAQUS software, showing an excellent agreement. Then frequency parameters of three plates for different boundary conditions and aspect ratios are graphically presented for a wide range of gradient index. Manuscript profile
      • Open Access Article

        8 - Elasto-plastic Analysis of Thick Walled Tanks Subjected to Internal Pressure
        Abbas Heydari MohamadTaghi Kazemi
        In this article, the Elasto-plastic analysis of thick walled FG tanks subjected to internal pressure is elaborated. Today, thick walled tanks containing liquids with high pressure are used in the chemical industries. The high internal pressure causes part of the thickne More
        In this article, the Elasto-plastic analysis of thick walled FG tanks subjected to internal pressure is elaborated. Today, thick walled tanks containing liquids with high pressure are used in the chemical industries. The high internal pressure causes part of the thickness of reservoir to yield; therefore, we need the Elasto-plastic analysis. In this study, Elasto-plastic behavior of FG cylindrical and spherical vessels under internal pressure is studied. For comparison with FG tanks, Elasto-plastic behavior of homogeneous tanks obtained. For this purpose, the assumption of ideal plastic behavior under axial symmetry conditions with using the Tresca criterion for the spherical and cylindrical tanks made of Al A359/SiCp is used. Power model is used for describe the gradual changes of mechanical properties in radial direction of FG material. It is shown that the analytically expressed results of the analysis of FG tanks after simplification coincide with homogeneous reservoirs. Furthermore, the bearing capacity of internal pressure will be higher relative to the homogenous tanks. Manuscript profile