Afshin Ahmadi Articles List

Open Access Article

1 - Effect of Injection Velocity on Heat Transfer of Water/Alumina Nano Fluid in A Rectangular Microchannel
Afshin Ahmadi Nadooshan Afshin Shiriny Morteza Bayareh

In this study, forced convection heat transfer of water/alumina Nano fluid in a rectangular microchannel with cross-flow injection is studied. The Nano fluid enters the microchannel with a temperature of 293 K and cools its walls. The upper wall of the microchannel is a More

In this study, forced convection heat transfer of water/alumina Nano fluid in a rectangular microchannel with cross-flow injection is studied. The Nano fluid enters the microchannel with a temperature of 293 K and cools its walls. The upper wall of the microchannel is at constant temperature of 303 K. On the lower wall, there are two holes for injection of Nano fluid flow. Other parts of the microchannel wall are insulated. Slip velocity boundary condition is used for the walls of the microchannel. Simulations are performed for different injection velocities and the results are presented as velocity and temperature fields, and variation of the Nusselt number. The results show that the slip velocity on the channel wall and the Nusselt number increase by increasing the injection velocity. It is revealed that the Nusselt number is maximum at the channel entrance and decreases along the channel. After each injection, local Nusselt number increases due to the increase of the temperature gradient in the microchannel. Moreover, an optimal value for the ratio of the injection velocity to the inlet velocity is achieved using performance evaluation criteria (PEC). It is concluded that is an optimal value of the injection velocity, leading to maximum PEC. Manuscript profile

Open Access Article

2 - Thermal Optimization of an Array of Needle-Shaped using Constructal Theory
Maryam Hoseinzadeh Afshin Ahmadi Nadooshan Morteza Bayareh

In the present paper, the constructal theory is employed to determine the optimal configuration of three rows of needle-shaped fins. The heat transfer across the fins is due to laminar forced convection. Second order upwind scheme is used for discretization of the diffu More

In the present paper, the constructal theory is employed to determine the optimal configuration of three rows of needle-shaped fins. The heat transfer across the fins is due to laminar forced convection. Second order upwind scheme is used for discretization of the diffusion terms of governing equations. The pressure–velocity coupling is performed using the SIMPLE algorithm. The heat transfer is optimized subject to constant fin volume. The effect of Reynolds number and thermal conductivity on the optimal configuration is investigated. The results obtained from the present simulations are in good agreement with the numerical results. The results show that pin–fins flow structure leads to the best performance when the pin–fin diameters and heights are non-uniform. At Re = 100 and 200, the optimal value of is 1.3. It is revealed that at Re = 50, the optimal value for is approximately 1.1. The results demonstrate that heat transfer rate is an increasing function of the Reynolds number. Manuscript profile

Open Access Article

3 - Numerical Simulation of Turbulent Nano-fluidFlow in a Circular Elbow
Afshin Ahmadi Nadooshan Marzieh Jafari farsani

force convection heat transfer of turbulent nano fluid flow in 90 and 60 degree elbow is simulated by using FLUENT. Single phase model has been implemented to study such a flow field and standard

force convection heat transfer of turbulent nano fluid flow in 90 and 60 degree elbow is simulated by using FLUENT. Single phase model has been implemented to study such a flow field and standard Manuscript profile

Open Access Article

4 - The Effect of Type and Location of a Phase Change Material (PCM) Layer in a Building Wall on Energy Consumption using Numerical Simulation
Arezoo Soleimani Dashtaki Afshin Ahmadi Nadooshan Afshin Abedi

Phase Change Materials (PCMs) have been the subject of many researches in recent years due to the storage and release of energy at low temperature ranges. PCMs store or releasing a large amount of energy at a constant temperature range leads to saving energy. In this pa More

Phase Change Materials (PCMs) have been the subject of many researches in recent years due to the storage and release of energy at low temperature ranges. PCMs store or releasing a large amount of energy at a constant temperature range leads to saving energy. In this paper, the numerical modelling of a multilayer composite wall including PCM located on the southern side of a building is carried out using an implicit method. The data correspond the fifteenth day of each month in Tehran. The governing equations are discretized by the implicit Crank Nicolson method and solved by iteration method using MATLAB software. Finally, the location and volume fraction of PCM in the wall of the building are studied to achieve maximum efficiency. The results show that the effect of latent and sensible heat results in a reduction in the input heat flux and thermal load to the building. The optimum location for the PCM layer is the middle layer of the composite wall to reduce the heat transfer rate inside the building. In addition, it is found that the PCM volume fraction in gypsum does not have a significant effect on the thermal performance of the multi-layer composite wall. Hence, low volume fraction reduces the costs without affecting the thermal performance of the building. Manuscript profile

Open Access Article

5 - Numerical Study on Forced Convection of Slip Flow in A Microchannel with Smooth and Sinusoidal Walls
Afshin Ahmadi Nadooshan DAriush Bahrami Akram Jahanbakhshi

10.30495/admt.2021.1926613.1265

The micro-scale equipment has many advantages, including high thermal performance, high surface-to-volume ratio in heat transfer, small size, low weight, low required fluid and high design flexibility. In this study, fluid flow inside a microchannel is modeled under the More

The micro-scale equipment has many advantages, including high thermal performance, high surface-to-volume ratio in heat transfer, small size, low weight, low required fluid and high design flexibility. In this study, fluid flow inside a microchannel is modeled under the assumption of laminar, incompressible, and two-dimensional flow under symmetric boundary conditions. The slip boundary condition is applied to the walls and the flow in the channel output is assumed to be fully developed. The effect of sinusoidal wall with the domain of 0.1 on the hydrodynamic and thermal behavior of the fluid is investigated and the results are compared with the results of smooth wall. The results show that for a constant Reynolds number, the maximum velocity decreases in the microchannel center by increasing the slip coefficient. Also, the comparison between the results of the wavy-wall microchannel and the microchannel with a smooth wall indicates that the heat transfer in the smooth microchannel is less than that in wavy-wall one. Considering the boundary conditions, the thermal behavior of the fluid is approximately the same for two cases in which both walls are sinusoidal and the only upper wall is sinusoidal. Manuscript profile

Open Access Article

6 - Heat Transfer of Wavy Microchannel Heat Sink with Microtube and Ag/Water-Ethylene Glycol Hybrid Nanofluid
Akram Jahanbakhshi Afshin Ahmadi Nadooshan morteza Bayreh

10.30486/admt.2023.1955556.1344

In the present study, novel channel geometries in a wavy channel heat sink (HS) are investigated using ANSYS-FLUENT software. The Ag/water-ethylene glycol (50%) nanofluid is selected for cooling the CPU in this HS. The second-order upwind method is employed to discretiz More

In the present study, novel channel geometries in a wavy channel heat sink (HS) are investigated using ANSYS-FLUENT software. The Ag/water-ethylene glycol (50%) nanofluid is selected for cooling the CPU in this HS. The second-order upwind method is employed to discretize the momentum Equation and the SIMPLEC algorithm is employed for coupling velocity and pressure fields. Comparison of the two HSs with and without microtube shows that the presence of the microtube increases the uniformity of the CPU surface temperature distribution and decreases the mean surface temperature of the CPU (TCPU-Mean). However, the pumping power consumption of the system increases about 10 times. The results also demonstrate that the addition of nanoparticles results in intensification in the Performance Evaluation Criterion (PEC) of the system and up to 30%, especially at high Reynolds numbers. Manuscript profile

Current Issue

Published Issues

Menu

Browse

List of Articles Afshin Ahmadi