List of articles (by subject) metal forming

---

• Open Access Article
  • Abstract Page
  • Full-Text
  
  1 - Experimental Investigation of Maximum Achievable Convolution Height of Metallic Bellows in Hydroforming Process
  Mehdi Safari Younes Ghadiri
• Open Access Article
  • Abstract Page
  • Full-Text
  
  2 - Impact of Loading Rate in Hot Tube Gas Forming of AA6063
  Mastafa Rajaee Seyed Jamal Hosseinipour Hamed Jamshidi Aval
• Open Access Article
  • Abstract Page
  • Full-Text
  
  3 - Multi-Objective Optimization of Loading Paths for Double-Layered Tube Hydroforming using Finite Element Analysis
  Hamed Ebrahimi Keshmarzi Ramin Hashemi Reza Madoliat
• Open Access Article
  • Abstract Page
  • Full-Text
  
  4 - Optimal Design of Steppers in Single Step High Pressure Torsion (SIHPT) Process as a Novel SPD Method
  Mehdi Eskandarzadeh Ghader Faraji A. Masoumi Ali Kalaki
• Open Access Article
  • Abstract Page
  • Full-Text
  
  5 - Multi-Objective Optimization of the Stamping of Titanium Bipolar Plates for Fuel Cell
  Vahid Modanloo Vali Alimirzaloo Majid Elyasi
• Open Access Article
  • Abstract Page
  • Full-Text
  
  6 - Fabrication of a Complicated Specimen with Two Point Incremental Forming Process
  Mehdi Safari Jalal Joudaki
• Open Access Article
  • Abstract Page
  • Full-Text
  
  7 - High-Velocity Compaction of Aluminum Powder by Gas Detonation Forming Technique
  Tohid Mirzababaie Mostofi Mostafa Sayah Badkhor Hashem Babaei
• Open Access Article
  • Abstract Page
  • Full-Text
  
  8 - Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets
  Sajad Bakhtiari Seyed Jalal Hashemi Amir Hossein Roohi
  10.30495/admt.2020.1880364.1147
• Open Access Article
  • Abstract Page
  • Full-Text
  
  9 - Hole-flanging of 2205 Dual-Phase Steel using Incremental Forming Process
  Amir H. Roohi Seyed Jalal Hashemi
  10.30495/admt.2021.1895361.1179
• Open Access Article
  • Abstract Page
  • Full-Text
  
  10 - Experimental Investigation on Process Parameters of Dissimilar Double-Layered Wire Produced by Modified Friction Stir Extrusion Process
  Masoud Yavari Nouri S. M. Hossein Seyedkashi Moosa Sajed
  10.30495/admt.2021.1911339.1220
• Open Access Article
  • Abstract Page
  • Full-Text
  
  11 - Stress and Strain Analysis in Cup Drawing Process for Different Materials using ANSYS Software
  siva prasad kondapalli GURRAM RAVITEJA
  10.30495/admt.2021.1934048.1294
• Open Access Article
  • Abstract Page
  • Full-Text
  
  12 - Experimental Analysis of Effective Parameters on the Bowing Defect of Symmetrical U-Section in Roll Forming Production
  Amin Poursafar Saeid Saberi Rasoul Tarkesh Esfahani Meisam Vahabi Javad Jafari Fesharaki
  10.30486/admt.2023.1960408.1355
• Open Access Article
  • Abstract Page
  • Full-Text
  
  13 - Numerical Simulation of Hot Forging Process of KIA Car Brake’s Output Shaft
  saeid Hashemian Peyman Mashhadi Keshtiban Abuzar Es'haghi Oskui
  10.30486/admt.2022.1933346.1290
• Open Access Article
  • Abstract Page
  • Full-Text
  
  14 - Strength Improvement of Nano-Structured Titanium Processed by Parallel Tubular Channel Angular Pressing
  Ali Amani Hamid Soleimanimehr Shahram Etemadi Haghighi Farid Biniyazan
  10.30486/admt.2022.1942680.1318