H

• H Safari.Keivan Energy Absorption by Thin-Walled Tubes with various Thicknesses in Rectangular and Square Sections under Different Quasi-Static Conditions: Experimental and Numerical Studies [ Vol.9, Issue 2 - Spring Year 2016]
• Habibalahi.Abbas Application of Pulsed eddy current technique to stress and residual stress measurement [ Vol.7, Issue 1 - Winter Year 2014]
• Habibi Sooha.Yousef Investigation of the AFM Indenter’s Geometry Effect On Micro/Nano Biological Cells’ Indentation [ Vol.13, Issue 4 - Autumn Year 2024]
• Habibnejad Korayem.Amin Determining Position and Orientation of 6R Robot using Image Processing [ Vol.11, Issue 1 - Winter Year 2024]
• Habibnejad korayem.Moharam Design and Manufacturing the Torque Gauge of ICaSbot and Implementing its Data Transfer Protocol [ Vol.6, Issue 2 - Spring Year 2013]
• Habibnejad korayem.Moharam Dynamic Load Carrying Capacity of Spatial Cable Suspended Robot: Sliding Mode Control Approach [ Vol.5, Issue 3 - Summer Year 2012]
• habibnejad.moharam Frequency Analysis of a Cable with Variable Tension and Variable Rotational Speed [ Vol.4, Issue 4 - Autumn Year 2011]
• habibnejad.moharam Dynamic Analysis of AFM in Air and Liquid Environments Considering Linear and Non-linear Interaction Forces by Timoshenko Beam Model [ Vol.8, Issue 2 - Spring Year 2015]
• habibnejad.moharam Frequency Response of AFM Nano Robot in Liquid by considering the effect of Cantilever's dimension and Environmental Parameters [ Vol.7, Issue 4 - Autumn Year 2014]
• habibnejad.moharam Design and implementation of feedback linearization control method to determine the DLCC of 6R manipulator [ Vol.8, Issue 3 - Summer Year 2015]
• habibnejad.moharam Optimal Trajectory Planning for Flexible Mobile Manipulators under Large Deformation Using Meta-heuristic Optimization Methods [ Vol.9, Issue 1 - Winter Year 2016]
• habibnejad.moharam Investigation of the AFM Indenter’s Geometry Effect On Micro/Nano Biological Cells’ Indentation [ Vol.13, Issue 4 - Autumn Year 2024]
• habibnejad.moharam Sliding Mode Control of AFM in Cantact Mode during Manipulation of Nano-particle [ Vol.6, Issue 4 - Autumn Year 2013]
• habibnejad.moharam Engineering Design of the Guidance System of the 6R Tele-robot based on DTMF [ Vol.7, Issue 3 - Summer Year 2014]
• habibnejad.moharam Longitudinal and Lateral Vibration Analysis of Cables in a Cable Robot Using Finite Element Method [ Vol.10, Issue 1 - Winter Year 2017]
• habibnejad.moharam Modeling and Optimal Control of a Sport Utility Cable Suspended Robot [ Vol.8, Issue 3 - Summer Year 2015]
• habibnejad.moharam Determining Position and Orientation of 6R Robot using Image Processing [ Vol.11, Issue 1 - Winter Year 2024]
• habibnejad.moharam Determining Maximum Dynamic Load Carrying Capacity of Cable Robots Between Two End Points of Workspace [ Vol.3, Issue 1 - Winter Year 2009]
• Hadavi.Seyed Mohammad Mehdi A study on the numerical simulation of thermo-mechanical behavior of the novel functionally graded thermal barrier coating under thermal shock [ Vol.8, Issue 2 - Spring Year 2015]
• Hadavinia.Homayoun Free Vibrations of Functionally Graded Circular Cylindrical Shells under Internal Pressure [ Vol.6, Issue 4 - Autumn Year 2013]
• Haddadi.Elyas The Choice of Automatic Welding Process and Technology by using WELD-EXP. Software [ Vol.1, Issue 1 - Winter Year 2007]
• Haddadpour.Hassan Modal and Aeroelastic Analysis of A High-Aspect-Ratio Wing with Large Deflection Capability [ Vol.8, Issue 1 - Winter Year 2015]
• Hadipeykani.Majid Thermomechanical Properties of the Polymeric Nanocomposite Predicted by Molecular Dynamics [ Vol.12, Issue 4 - Autumn Year 2024]
• Hadipour.Mojtaba Investigation of the Stability of the Ball and Beam by the PID Controller [ Vol.14, Issue 1 - Winter Year 2024]
• Haghani.Ahmad Effect of Non-Newtonian Models on Blood Flow in Artery with Different Consecutive Stenosis [ Vol.11, Issue 1 - Winter Year 2024]
• Haghani.Ahmad Predicting Strip Tearing in Cold Rolling Tandem Mill using Neural Network [ Vol.8, Issue 1 - Winter Year 2015]
• Haghani.Ahmad Investigation of Mechanical Property and Microstructure of Nanocomposite AZ31/SiC Fabricated by Friction Stir Process [ Vol.9, Issue 2 - Spring Year 2016]
• haghighi.mahmoud Free Vibration of Defective Nanographene using Molecular Dynamics Simulation and Differential Quadrature Method [ Vol.14, Issue 4 - Autumn Year 2024]
• Haghpanahi.Mohammad Optimal Trajectory Planning for Flexible Mobile Manipulators under Large Deformation Using Meta-heuristic Optimization Methods [ Vol.9, Issue 1 - Winter Year 2016]
• Haghpanahi.Mohammad Different Geometry Design Structures of Tissue Scaffolds for Additive Manufacturing [ Vol.14, Issue 4 - Autumn Year 2024]
• Haghpanahi.Mohammad Numerical simulation of multilayer cellular scaffolds with 3D and 1D elements [ Vol.13, Issue 4 - Autumn Year 2024]
• haj ahmad.ali Vibration Analysis of Rectangular Kirchhoff Nano-Plate using Modified Couple Stress Theory and Navier Solution Method [ Vol.14, Issue 2 - Spring Year 2024]
• Haji Mohamadi.Sayad The Finite Element Method and Genetic Algorithm Approaches on Shape Optimization of Prosthesis According to Fatigue Behavior [ Vol.3, Issue 3 - Summer Year 2010]
• Hajipour.Alireza Comparison of performances of air standard Atkinson, Diesel and Otto cycles with constant specific heats [ Vol.6, Issue 3 - Summer Year 2013]
• Hajizadeh.Iman Multiobjective Constrained Optimization of a Newly Developed Needle Driving Mechanism in the Sewing Machine for Improvement of the Mechanical Performance [ Vol.7, Issue 4 - Autumn Year 2014]
• Hajizadeh.khatereh Developing a 3D Multi-Body Model of the Scoliotic Spine with Lateral Bending Motion for Comparison of Ribcage Flexibility [ Vol.6, Issue 1 - Winter Year 2013]
• Hakimollahi.Mansour Simulation of Friction Stir Extrusion using Smoothed Particle Hydrodynamics (SPH) [ Vol.15, Issue 2 - Spring Year 2024]
• Hamedi.Mohsen Study of the Resonant Frequency of Unimorph Triangular V-shaped Piezoelectric Cantilever Energy Harvester [ Vol.8, Issue 4 - Autumn Year 2015]
• Hamidizadeh.Hadi Numerical Study of Microbeam with Geometric Discontinuity Under Electrostatic Load using Strain Gradient Theory [ Vol.13, Issue 1 - Winter Year 2024]
• Hamzekhani.Samane Experimental Investigation and Modeling of Bubble Departure Frequency for Nucleate Pool Boiling Heat Transfer of Pure Liquids on Flat Heater [ Vol.15, Issue 4 - Autumn Year 2024]
• Hamzeloo.S. R. Investigating the Effect of Cutting Condition on the Plastic Energy in Turning Process of AISI 1050 [ Vol.12, Issue 3 - Summer Year 2024]
• Harirbafan.Ebrahim Estimation of Thrust Stand Structure Fatigue Life Under Solid Motors Random Vibrations Effects [ Vol.1, Issue 4 - Autumn Year 2008]
• Harirbafan.Ebrahim Analytical and Simulation of Free-Free Beam Subjected to Concentrated Impact Loadings [ Vol.2, Issue 1 - Winter Year 2008]
• Harirbafan.Ebrahim Analytical Solution and Simulation of Flexible Joint in Thrust Vector Control System under Bending [ Vol.2, Issue 2 - Spring Year 2009]
• Harirbafan.Ebrahim Dynamic Design Principles of a Thrust Stand and Methods of Improving Frequency Response [ Vol.2, Issue 1 - Winter Year 2008]
• hasanian.masood Gas Pipeline Corrosion Mapping Using Pulsed Eddy Current Technique [ Vol.5, Issue 1 - Winter Year 2011]
• Hasanpour.Kourosh Finite Element Analysis of Self Destruction Mechanism in a Mechanical Controller [ Vol.3, Issue 2 - Spring Year 2010]
• Hasanpour.Kourosh Analysis of the Dynamical Behavior of the Delay Mechanism in a Projectile Motion Controller, Using 3D Finite Element Simulation [ Vol.3, Issue 3 - Summer Year 2010]
• hasanzade.yasha Development of A New Correlation for Estimating Pressure Gradient of Oil- Water Two Phase Flow in A Horizontal Pipe [ Vol.14, Issue 4 - Autumn Year 2024]
• Hasanzadeh.Hasan On Using the Fourth Order Finite Difference Method in Studying Orthotropic Rectangular Plate's Vibration Behavior [ Vol.1, Issue 4 - Autumn Year 2008]
• Hasanzadeh.Hasan Numerical Study of Increasing Error Order in Finite Difference Method Used for Analyzing the Rectangular Isotropic Plate's Vibration Behavior [ Vol.1, Issue 3 - Summer Year 2008]
• Hasanzadeh.Hasan Numerical Analysis of Plate’s Vibration Behavior with Non-linear Edge under Various Boundary Conditions [ Vol.1, Issue 2 - Spring Year 2008]
• Hashemi.Ramin Multi-Objective Optimization of Loading Paths for Double-Layered Tube Hydroforming using Finite Element Analysis [ Vol.12, Issue 1 - Winter Year 2024]
• Hashemi.S. Jalal Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets [ Vol.13, Issue 3 - Summer Year 2024]
• Hashemi.S. Jalal Hole-flanging of 2205 Dual-Phase Steel using Incremental Forming Process [ Vol.14, Issue 1 - Winter Year 2024]
• Hashemi.Sayed Alireza Micro-Finite Element Model to Investigate the Mechanical Stimuli in Scaffolds Fabricated via Space Holder Technique for Cancellous Bone [ Vol.13, Issue 1 - Winter Year 2024]
• Hashemian.saeid Numerical Simulation of Hot Forging Process of KIA Car Brake’s Output Shaft [ Vol.15, Issue 1 - Winter Year 2024]
• Hashemzadeh.Majid The Effect of Focal Distance and Type of Auxiliary Gas on Cut Width in CO2 Laser Cutting of Stainless and Mild Steel Sheets [ Vol.11, Issue 4 - Autumn Year 2024]
• Hassani.Mohsen Experimental and Numerical Investigation of the Arms Displacement in a New Electrothermal MEMS Actuator [ Vol.10, Issue 2 - Spring Year 2017]
• Hatami.Amin Scheduling of Unrelated Parallel Machines using Two Multi Objective Genetic Algorithms with Sequence-Dependent Setup Times and Precedent Constraints [ Vol.8, Issue 4 - Autumn Year 2015]
• Heidari.Ali Evaluation of S/N Diagram in Welded Joints Based on Different Fatigue Failure Criteria [ Vol.13, Issue 3 - Summer Year 2024]
• Heidari.Ali Optimizing Friction Stir Welding Process for Enhancing Strength and Hardness using Taguchi Multi-Objective Function Method [ Vol.12, Issue 3 - Summer Year 2024]
• Heidari.Mohammad Genetic Algorithm and ANN for Estimation of SPIV of Micro Beams [ Vol.10, Issue 4 - Autumn Year 2017]
• Heidari.Mohammad Prediction of Residual Stresses by Radial Basis Neural Network in HSLA-65 Steel Weldments [ Vol.8, Issue 2 - Spring Year 2015]
• Heidari.Mohammad Faults diagnosis of a girth gear using discrete wavelet transform and artificial neural networks [ Vol.7, Issue 3 - Summer Year 2014]
• Heirani.Hasan Investigation of Magnitude and Position of Maximum von Mises Stress in The Cylindrical Contact Problems [ Vol.16, Issue 3 - Autumn Year 2023]
• hemati.seyed jalal Bone Surface Model Development Based on Point Clouds Extracted From CT Scan Images [ Vol.10, Issue 2 - Spring Year 2017]
• Hemmasian.MohamadMehdi Drag-Reduction Characteristics in Air Flow over the Iced Surface at Re>104 [ Vol.1, Issue 2 - Spring Year 2008]
• hesari.yaser Dynamic Modelling and Control of a Dielectric Elastomer Actuator with Two Degrees of Freedom [ Vol.11, Issue 3 - Summer Year 2024]
• Heydari Beni.Mohsen Dynamic Analysis of Carbon Nanotube-Reinforced Multilayer Composite Plates [ Vol.14, Issue 1 - Winter Year 2024]
• Heydari Beni.Mohsen Design and Fabrication of a Composite Energy Absorber [ Vol.13, Issue 4 - Autumn Year 2024]
• Heydari Beni.Mohsen Numerical and Experimental Static Bending Analysis of Composite Sandwich Panels with Grid-Stiffened Cores Before and After Transverse Impact Loading [ Vol.15, Issue 1 - Winter Year 2024]
• heydari vini.mohammad A New Rolling Pressure Model for An Actual Reversing Cold Rolling Strip Mill [ Vol.8, Issue 2 - Spring Year 2015]
• heydari vini.mohammad Mechanical Properties and Microstructural Evolution of AA5083/Al2O3 Composites Fabricated by Warm Accumulative Roll Bonding [ Vol.9, Issue 4 - Autumn Year 2016]
• heydari vini.mohammad Fabrication of Aluminum/Gr Composites and Investigation of its Tribological and Wear Properties [ Vol.16, Issue 3 - Autumn Year 2023]
• heydari vini.mohammad Fabrication of AA1060/Al2O3 Composites by Warm Accumulative Roll Bonding Process and Investigation of its Mechanical Properties and Microstructural Evolution [ Vol.10, Issue 4 - Autumn Year 2017]
• Heydari.A. Buckling of Functionally Graded Beams with Rectangular and Annular Sections Subjected to Axial Compression [ Vol.5, Issue 1 - Winter Year 2011]
• heydari.abbas Analytical solutions for buckling of functionally graded circular plates under uniform radial compression by using Bessel function [ Vol.6, Issue 4 - Autumn Year 2013]
• Heydari.Abbas Elasto-plastic Analysis of Thick Walled Tanks Subjected to Internal Pressure [ Vol.3, Issue 1 - Winter Year 2009]
• Heydari.Abbas Buckling Analysis of Discontinues Fractional Axially Graded Thin Beam with Piecewise Axial Load Function Rested on Rotational Spring Hinges [ Vol.13, Issue 2 - Spring Year 2024]
• heydari.mohammad Fabrication of AA1060/Al2O3 Composites by Warm Accumulative Roll Bonding Process and Investigation of its Mechanical Properties and Microstructural Evolution [ Vol.10, Issue 4 - Autumn Year 2017]
• Heydari.Mojtaba Estimation of Thrust Stand Structure Fatigue Life Under Solid Motors Random Vibrations Effects [ Vol.1, Issue 4 - Autumn Year 2008]
• Heydari.Mojtaba Analytical Solution and Simulation of Flexible Joint in Thrust Vector Control System under Bending [ Vol.2, Issue 2 - Spring Year 2009]
• Heydari.Mojtaba Vibration Analysis and Design of Dynamic Absorber in a Vertical Drilling Machine [ Vol.2, Issue 2 - Spring Year 2009]
• Heydari.Mojtaba Dynamic Design Principles of a Thrust Stand and Methods of Improving Frequency Response [ Vol.2, Issue 1 - Winter Year 2008]
• Heydari.Vahid Modal Analysis of Complex Structures via a Sub-Structuring Approach [ Vol.14, Issue 1 - Winter Year 2024]
• Hojjatti Najafabadi.akbar Mechanical Design and Simulation of a Saddle-Assistive Device for Sit-to-Stand Transfer in Healthy Subjects [ Vol.10, Issue 4 - Autumn Year 2017]
• Homaei.Hadi Faults diagnosis of a girth gear using discrete wavelet transform and artificial neural networks [ Vol.7, Issue 3 - Summer Year 2014]
• Homami.Rasool Experimental investigation and mathematical modeling of the composite ceramic cutting tools with alumina base in the machining process of PH-hardened Austenitic-ferritic (Duplex) stainless steel [ Vol.5, Issue 2 - Spring Year 2012]
• homayouni.mostafa Stress analysis of rotational shaft with a constant angular speed using strain gradient theory [ Vol.5, Issue 5 - Winter Year 2012]
• Honarpishe.Mahmoud Numerical Study of Effective Parameters on Cold Rolling of Tri-layers Al/St/Al and Cu/Al/Cu [ Vol.3, Issue 1 - Winter Year 2009]
• Honarvar.Farhang Monitoring of Pipe-Wall Thickness and Thinning Rate by Ultrasonic Technique [ Vol.5, Issue 4 - Autumn Year 2012]
• Hooshmand.Mehdi The Case Examination of Detection of Structural Damages on a Plate using Wavelet Transform [ Vol.13, Issue 2 - Spring Year 2024]
• Hoseini Sarvari.Sayed Masoud Effects of Cooling Air Direction and Velocity on a Branwheat Biscuit’s Temperature in the Cooling Line of Razavi Food Industries Company [ Vol.2, Issue 4 - Autumn Year 2009]
• Hoseini.Rouhollah Investigation into the Importance of Pre-Design Procedure in Vibration Absorbers Installations [ Vol.4, Issue 1 - Winter Year 2010]
• hoseini.seyed Drilling of Engineering Ceramics using Combination of Ultrasonic Vibrations and Diamond Slurry [ Vol.6, Issue 2 - Spring Year 2013]
• Hoseinipour.Sayed Jamal Finite Element Simulation of Pulsating Hydroforming of Tube in Box-Shaped Die [ Vol.1, Issue 2 - Spring Year 2008]
• Hoseinpour.Mohhamad The Numerical Modeling to Study the Multi-Pass Friction Stir Processing on Magnesium Casting Alloy AZ91 [ Vol.12, Issue 4 - Autumn Year 2024]
• Hoseinzadeh.Maryam Thermal Optimization of an Array of Needle-Shaped using Constructal Theory [ Vol.11, Issue 3 - Summer Year 2024]
• Hoshiar.Ali Developing a control strategy for AFM nano- micro manipulation [ Vol.8, Issue 2 - Spring Year 2015]
• Hosseingholi pourasl.hamed Finite Element Prediction on the Machining Stability of Boring Machine with Experimental Verification [ Vol.8, Issue 1 - Winter Year 2015]
• Hosseini Harat.Seyyed Mohammad Effect of Non-Newtonian Models on Blood Flow in Artery with Different Consecutive Stenosis [ Vol.11, Issue 1 - Winter Year 2024]
• hosseini moghdam omami.ali Studying the Behavior of a Variable Pitch “Hydro Screw” Micro Hydro Turbine, Numerical Analysis and Experimental Investigation [ Vol.12, Issue 4 - Autumn Year 2024]
• Hosseini.Mir Amin Machine Tool Design Optimization of High Resolution Parallel Hexapod in Cartesian Workspace [ Vol.4, Issue 3 - Summer Year 2011]
• Hosseini.Mir Amin Kinematic Analysis of a Novel 3-CRS/PU Parallel Manipulator [ Vol.5, Issue 5 - Winter Year 2012]
• Hosseini.MirAmin Kinematic Synthesis of a Novel Parallel Cable Robot as Artificial Leg [ Vol.9, Issue 3 - Summer Year 2016]
• Hosseini.Rouhollah Investigation of Adhesion Behavior of Aluminum Laminates /Carbon Fiber/ High Silica Fiber by Phenol Resins [ Vol.16, Issue 3 - Autumn Year 2023]
• Hosseini.Rouhollah Study of the Resonant Frequency of Unimorph Triangular V-shaped Piezoelectric Cantilever Energy Harvester [ Vol.8, Issue 4 - Autumn Year 2015]
• Hosseini.Rouhollah Investigation of Adhesion Behavior of Aluminum Laminates /Carbon Fiber/ High Silica Fiber by Phenol Resins [ Vol.16, Issue 3 - Autumn Year 2023]
• Hosseinipour.Seyed Jamal Impact of Loading Rate in Hot Tube Gas Forming of AA6063 [ Vol.12, Issue 1 - Winter Year 2024]
• Hosseini-Sianaki.Ahmad Effect of CaCO3 Nanoparticles on Vibrational Damping Behavior and Static Mechanical Properties of Polypropylene Composite Plates: An Experimental Investigation [ Vol.15, Issue 1 - Winter Year 2024]
• Hosseini-Sianaki.Ahmad Vibration Analysis of an Imperfect Single-Layer Graphene Sheet using Quasi-3d Theory and Isogeometric Approach [ Vol.16, Issue 1 - Spring Year 2023]
• Hosseinzadeh.Ali Leaching of Metals from Dental Silver Alloy Wastes [ Vol.15, Issue 2 - Spring Year 2024]
• Hosseinzadeh.Ali Effect of Inter-Cavity Spacing and Heat Treatment in Friction Stir Processing/Welding (FSP/FSW) Al7075 Composites Containing Al2O3 and Graphene Nanomaterials using Charpy Impact Test [ Vol.16, Issue 1 - Spring Year 2023]
• Hosseinzadeh.Ali Investigation of the Stability of the Ball and Beam by the PID Controller [ Vol.14, Issue 1 - Winter Year 2024]
• Hosseinzadeh.Ali Investigation of The Effect of Notch Tip Radius on Fracture Energy of Charpy in 7075 Aluminium Alloy [ Vol.13, Issue 2 - Spring Year 2024]
• Hossienzadeh.Morteza Feasibility study on aluminum alloys and A441 AISI steel joints by friction stir welding [ Vol.7, Issue 4 - Autumn Year 2014]
• Hossienzadeh.Morteza Effects of friction stir welding tool plunge depth on microstructure and texture evolution of AA1100 to A441 AISI joint [ Vol.9, Issue 1 - Winter Year 2016]