Effects of Active Material Particles Size Distribution on the Fabrication of TiNb2O7 Electrode Used in Lithium-Ion Batteries

محورهای موضوعی : Materials synthesis and charachterization

Touraj Adhami ¹ , Reza Ebrahimi-Kahrizsangi ² , Hamid Reza Bakhsheshi Rad ³ , Somayeh Majidi ⁴ , Milad Ghorbanzadeh ⁵

1 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Najafabad, Iran
2 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Najafabad, Iran
3 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Najafabad, Iran
4 - Department of Chemistry, Najafabad Branch, Islamic Azad University, Najafabad, Iran
5 - Materials and Energy Research Center, Karaj, Iran

تاریخ دریافت : 1399/12/24 تاریخ پذیرش : 1400/02/28 تاریخ انتشار : 1400/05/10

کلید واژه: particle size, Electrode, Anode materials, uniform distribution, Li ion battery,

چکیده مقاله :

In this study effect of active material particle size distribution (PSD) on TiNb2O7 electrodes and their performance were evaluated. To determine the effect of PSD, have focused on the performance of the electrode, which is mainly affected by the performance of individual particles and their interaction. For this purpose, TiNb2O7 was successfully synthesized by mechanochemical method and post-annealing, as an anode material for lithium-ion batteries. Phase identifications and microstructure characterization was carried out by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) to identify the phases and evaluate the morphology of the synthesized samples. The charging and discharging tests were conducted using a battery-analyzing device for evaluating the electrochemical properties of the fabricated anodes. Eventually, at faster charging rates, the electrochemical performance was found to be improved when smaller active material particle size distribution was used. Differences in particles size distributions resulted in variable discharge capacities so that the sample with particle size higher than 25 microns (>25 μm) showed a capacity of 19 mAh/g after 179 cycles, which had a lower capacity than their sample with particle size less than 25 microns (<25 μm). The final capacity of the sample with a particle size less than 25 microns is 72 mAh/g.

منابع و مأخذ:

[1] Y. Liu, Y. Yang, “Recent progress of TiO₂-based anodes for Li ion batteries”, Journal of Nanomaterials, vol. 2016, 2016, pp. 1-15.

[2] S. K. Balasingam, M. Kundu, B. Balakrishnan, H. Kim, A. M. Sevensson, K. Jayasayee, “Hematite microdisks as an alternative anode material for lithium-ion batteries”, Materials Letters, vol. 247, 2019, pp. 163-166.

[3] S. Li, X. Cao, C. N. Schmidt, Q. Xu, E. Uchaker, Y. Pei, G. Cao, “TiNb₂O₇/graphene composites as high-rate anode materials for lithium/sodium ion batteries”, Journal of Materials Chemistry A, vol. 4, 2016, pp. 4242-4251.

[4] X. Xia, Sh. Deng, Sh. Feng, J. Wu, J. Tu, “Hierarchical porous Ti₂Nb₁₀O₂₉ Nanospheres as superior anode materials for lithium-ion storage”, Journal of Materials Chemistry A, vol. 5 2017, pp. 21134-21139.

[5] D. Pham-cong, J. Kim, V. T. Tran, S.J. Kim, S. Jeong, J. Choi, Ch. Cho, “Electrochemical behavior of interconnected Ti₂Nb₁₀O₂₉ nanoparticles for high-power Li-ion battery anodes”, Electrochimica Acta, vol. 236, 2017, pp. 451-459.

[6] G. Zhu, Y. Wang, Y. Xia, “Ti-based compounds as anode materials for Li-ion batteries”, Energy & Environmental Science, vol. 5, 2012, pp. 6652-6667.

[7] D. Aurbach, B. Markovsky, I. Weissman, E. Levi, Y. Ein-Eli, “On the correlation between surface chemistry and performance of graphite negative electrodes for Li ion batteries”, Electrochimica Acta, vol. 45, 1999, pp. 67-86.

[8] B. Michalak, H. Sommer, D. Mannes, A. Kaestner, T. Brezesinski, J. Janek, “Gas Evolution in Operating Lithium-Ion Batteries Studied in Situ by Neutron Imaging”, Scientific Reports, vol. 5, 2015, pp. 1-9.

[9] F. Rçder, S. Sonntag, D. Schrçder, U. Krewer, “Simulating the Impact of Particle Size Distribution on the Performance of Graphite Electrodes in Lithium-Ion Batteries”, Energy Technology, vol. 4, 2016, pp. 1-11.

[10] Zh. Wu, W. Ren, L. Wen, L. Gao, J. Zhao, Z. Chen, G. Zhou, F. Li, H. Cheng, “Graphene Anchored with Co₃O₄ Nanoparticles as Anode of Lithium-Ion Batteries with Enhanced Reversible Capacity and Cyclic Performance”, ACS Nano, vol. 4, 2010, pp. 3187-3194.

[11] G. T. Feya, Y. G. Chen, H. Kao, “Electrochemical properties of LiFePO₄ prepared via ball-milling”, Journal of Power Sources, vol. 189, 2009, pp. 169-178.

[12] Th. Drezen, N. Kwon, P. Bowen, I. Teerlinck, M. Isono, I. Exnar, “Effect of particle size on LiMnPO₄ cathodes”, Journal of Power Sources, vol. 189, 2009, pp. 169-178.

[13] T. Adhami, R. Ebrahimi-Kahrizsangi, H. R. Bakhsheshi-Rad, S. Majidi, M. Ghorbanzadeh, F. Berto, “Synthesis and electrochemical properties of TiNb₂O₇ and Ti₂Nb₁₀O₂₉ anodes under various annealing atmospheres”, Metals, vol. 11, 2021, pp. 1-12.

[14] A. R. Madram, R. Daneshtalab, M. R. Sovizi, “Effect of Na⁺ and K⁺ co-doping on the structure and electrochemical behaviors of LiFePO₄/C cathode material for lithium-ion batteries”, Royal Society of Chemistry, 2016, pp. 101477-101484.

[15] L. Buannic, J. Colin, Lise Daniel, S. Patoux, “Effect of syntheses and post synthetic treatments on mixed titanium niobium oxides for use as negative electrode in high power Li-ion batteries”, Electrochemical Society, 2013.