Effects of Shielding Gas on the Depth, Width and Hardness of 17-4PH Stainless Steel during TIG Welding
محورهای موضوعی : Journal of Environmental Friendly MaterialsS, M Hosseini Farzaneh 1 , M Belbasi 2
1 - Department of Petroleum, Mining and Materials Engineering, Tehran Central Branch, Islamic Azad University, Tehran, Iran.
2 - Department of Petroleum, Mining and Materials Engineering, Tehran Central Branch, Islamic Azad University, Tehran, Iran.
کلید واژه:
چکیده مقاله :
The present study investigates the effects of type of shielding gas on the depth, width and hardness of 17-4PH stainless steel. For this purpose, pure He, pure Ar and 80%Ar + 20% He were used as shielding gases in TIG welding of 17-4PH SS. Weld depth and width of specimens were measured by macro etching. Microstructure of welds was studied by using SEM technique. Moreover, micro Vickers hardness test was accomplished to gauge the hardness of welds. Results showed that specimen welded with pure He has the highest hardness values in the weld zone due to the reduction of δ-ferrite formation in the martensitic matrix. Furthermore, owing to the lower thermal conductivity and heat input of Ar gas, specimen welded by pure Ar has the shallowest and narrowest weld bead. However, due to produce hotter arc by addition of He in shielding gas, enhancements observed in the weld depth and width of specimens welded with pure He and 80%Ar + 20% He.
[1] A. Gharebaghi, Precipitation Study in a High Temperature Austenitic Stainless Steel using Low Voltage Energy Dispersive X-ray Spectroscopy. Royal Institute of technology, Sweden, (2012).
[2] F. Christien and R. Le Gall, Scr. Mater., 48, (2003), 11.
[3] ASM Metals Handbook, "Metallography and Microstructures, Stainless Steel Casting Alloys", Vol. 9, (2004).
[4] J. C. Lippold and D. J. Kotecki, Intro. Mater. Sci., 376. Wiley-VCH, (2005).
[5] 17-4PH Specification Sheet, Sandmeyer Steel Company, PA.
[6] C. R. Das, H. C. Dey, G. Srinivasan, S. K. Albert, A. K. Bhaduri and A. Dasgupta, Sci. Technol. Weld. Joi., 11, 52006, (2006), 502.
[7] P. Maj, B. Adamczyk-Cieslak, M. Lewczuk, J. Mizera, S. Kut and T. Mrugala, J. Mater. Eng. Perf., (2018), 1;27(12):6435-42.
[8] J. Ma, MM. Atabaki, W. Liu, R. Pillai, B. Kumar, U. Vasudevan and R. Kovacevic, Opt. Laser Technol., (2016), 1;82, 38.
[9] Crown Er630 (17-4 PH) data sheet, Crown Alloys Company.
[10] Evans RM, Martin DC, Vagi JJ. Welding of precipitation-hardening stainless steels. NASA Marshall Space Flight Center, 1968.
[11] B. Zarei, H. TaghipourArmaki, H. Shadi, A. Moradi, B. Delikhoon, M. Karami et al., Welding and Coating by Shielding Gas, Iran Course Book Publication Company, Tehran, Iran, 1th ed., 2018.
[12] I. Bitharas, S. W. Campbell, A. M. Galloway, N. A. McPherson and A. J. Moore, Mater. Des., (2016), 5;91:424-31.
[13] W. Liu, J. Ma, M. M. Atabaki, R. Pillai, B. Kumar, U. Vasudevan, H. Sreshta and R. Kovacevic, Laser. Manuf. Mater. Process., (2015), 1;2(2),74.
[14] S. A. HoseiniHoseinabad, Sch. Metall. Mater. Eng., (2008), 119.
[15] M. B. Balajaddeh and H. Naffakh-Moosavy, Opt. Laser. Technol., (2019), 1;119:105651.
[16] A. R. Sufizadeh and S. A. A. AkbariMusavi, Metall. Eng. Soci. Iranian Fdy. men, 2008.
[17] F. TatiKhaniverdi, M. R. KarimiNoori and M. Belbasi, Effect of Welding Parameters on Depth of Penetration and Depth to Width Ratio in TIG Welding of Ti-6Al-4V Alloy, 1st National Conference on Mechanical Engineering of Iran, Shiraz, Iran, (2014).
[18] N. R. Mandal, Aluminium welding. Woodhead publishing; (2001) Jan 15.
[19] Y. Najafi, F. MalekGhaini, Y. Palizdar and S. Gholami, J. Weld. Sci. Technol. of Iran., (2016), 2(1), 69.
