List of Articles Selective laser melting Open Access Article Abstract Page Full-Text 1 - Effect of Surface Treatment and Heat Treatment on the Microstructure and Mechanical Properties of Ti6Al4V Alloy Manufactured by Selective Laser Melting Q Salim Shaher M Razazi Boroujeni S Nosohiyan Open Access Article Abstract Page Full-Text 2 - The Effect of Cooling Rate on the Solutionizing of IN718 Superalloy Produced via Selective Laser Melting (SLM) Method H. H. Dastgerdi M. O. Shabani Y. Shajari Open Access Article Abstract Page Full-Text 3 - Evaluation of Corrosion Behavior of 316 L Stainless Steel Manufactured by SLM Method After Heat Treatment and Surface Treatments S Abdulnabi Wali M Razazi Boroujeni S Nosohiyan Open Access Article Abstract Page Full-Text 4 - Investigation of additive manufacturing of porous Ti-6Al-4V alloy: Geometry analysis for dental applications Mohammad Hossein Malekipour Esfahani Fatemeh Safdarian Sharif Heydari Open Access Article Abstract Page Full-Text 5 - investigating the effect of porosity Percentage on heat transfer in plastic injection molds created by selective laser melting Seyed mostafa MirTabaei Afshin Judaki Morteza Taher Niya Open Access Article Abstract Page Full-Text 6 - Investigating on the microstructure of cross-section and surface of Ti-10Mo alloy produced by selective laser melting Karim Avak Maziyar Azadbeh Samira Eslami Mehdi Ojaghi 10.30495/jnm.2024.32954.2026 Open Access Article Abstract Page Full-Text 7 - A simple and efficient method for creating the beta phase through the selective laser melting process of Ti-10Mo powder mixed alloy; A corrosion approach Arezoo Pourshoja karim Avak Maziyar Azadbeh Mohammadreza Etminanfar Mehdi Ojaghi 10.30495/jnm.2024.33378.2040 Open Access Article Abstract Page Full-Text 8 - Introduction: Titanium alloys containing the β phase have much better corrosion resistance. Some alloying elements, such as Mo, stabilize this phase. Among the Ti alloys that contain this element, the Ti-10Mo alloy is of particular importance. If this alloy is produced using selective laser melting (SLM), it will be an approach that is user-friendly due to the nature of the process. Methods: Samples were printed by SLM process. The constituent phases were determined by XRD. The microstructure was evaluated using optical and scanning electron microscopes. Corrosion behavior was evaluated by cyclic potentiodynamic polarization and electrochemical impedance spectroscopy. Findings: In the XRD pattern of pure Ti powder and printed sample, α and α/α' phases are seen, respectively. However, Ti-10Mo powder mixture consists of α and Mo phases, the β phase is more dominant in printed sample because of the Mo penetration in the Ti matrix. As well as, in the microstructure of Ti10Mo the beta phase is seen as Mo-rich streaks, whereas in pure Ti it is found relatively negligible as epitaxially grown primary columnar β grains with acicular α' martensite phase. Mo addition to pure Ti reduces its passive current density and stabilize oxide film. However, Ti-10Mo alloy, with its various phases and galvanic couples, experiences rupture of the passive oxide film at higher potentials, leading to pitting corrosion. The impedance module value of Ti-10Mo is higher than that of pure Ti. Both samples have a double passive oxide film, with Ti-10Mo alloy exhibiting higher resistance than pure Ti. Arezoo Pourshoja karim Avak مازیار آزادبه Mohamadreza Etminanfar Mehdi Ojaghi Open Access Article Abstract Page Full-Text 9 - Evaluation of the Corrosion Behavior of Inconel 625 Superalloy Made by SLM Method Lamyaa Idkhayyil Mahood ALLKASHEESH mohammad razazi boroujeni
