The Effect of Cooling Rate on the Solutionizing of IN718 Superalloy Produced via Selective Laser Melting (SLM) Method

Subject Areas : Journal of Environmental Friendly Materials

H. H. Dastgerdi ¹ , M. O. Shabani ² , Y. Shajari ³

1 - Iran University of Industries and Mines (IUIM), Tehran, Iran
2 - Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran, Iran
3 - Institute of Materials and Energy, Meshkin Dasht, Karaj, Iran

Received: 2018-09-05 Accepted : 2019-03-15 Published : 2019-03-15

Keywords: Hardness, Microstructure, IN718 Superalloy, Selective Laser Melting (SLM), Solution Heat Treatment,

References:

[1] M. G. Oskouei : Gas Turbines, Ministry of Energy, Tehran, (2002), 73.

[2] L. A. Jackman : Forming, Fabrication and Heat Treatment of Superalloys, , in Superalloys Source Book, ASM, New York, (1984), 217.

[3] Y. Shajar and S. H. Razavi, 5^th Int. Conf. of Materials and Metallurgy, iMat, Shiraz, ( 2016), 215.

[4] S. Bose and A. Bandyopadhyay : Additive Manufacturing, CRC Press, Boca Raton, Florida, CRC Press, (2016), 75.

[5] A. A. Antonysamy, , Ph.D. Thesis, University of Manchester, Manchester, (2012).

[6] B. Zhang, H. Liao, and C. Coddet, App. Surf. Sci., 279 (2013), 310.

[7] K. N. Amato, S. M. Gaytan, L. E. Murr, E. Martinez, P. W. Shindo, J. Hernandez, S. Collins, and F. Medina, Acta. Materialia.60 (2012), 2229.

[8] J. P. Choi, G. H. Shin, S. Yang, D. Y. Yang, J. S. Lee, M. Brochu and J. H. Yu, Powder. Technol.310 (2017), 60.

[9] J. Strößner, M. Terock and U. Glatzel. Adv. Eng Mater.,17 (2015), 1099.

[10] Q. Jia and D. Gu, J. Alloy. Compd.,585 (2014), 713.

[11] D. Zhang, W. Niu, X. Cao, and Z. Liu, Mater. Sci. Eng. A., 644 (2015), 32.

[12] T. Trosch, J. Strößner, R. Völkl, and U. Glatzel, Mater. Letters.,164 (2016), 428.

[13] E. Chlebus, K. Gruber, B. Kuźnicka, J. Kurzac, and T. Kurzynowski, Mater. Sci. Eng. A.,639 (2015), 647.

[14] M. E. Aydinöz, F. Brenne, M. Schaper, C. Schaak, W. Tillmann, J. Nellesen, and T. Niendorf, Mater. Sci. Eng.,669 (2016), 246.

[15] Z. Wang, K. Guan, M. Gao, X. Li, X. Chen, and X. Zeng, J. Alloy. Compd.513 (2012), 518.

[16] D. H. Smith, J. Bicknell, L. Jorgensen, B. M. Patterson, N. L. Cordes, I. Tsukrov, and M. Knezevic, Mater. Character., 113 (2016), pp. 1.

[17] Y. L. Kuo, S. Horikawa, and K. Kakehi, Mater. Design.,116 (2017), 411.

[18] M. F. Zaeh and G. Branner, Production. Eng.,4 (2010), 35.

[19] P. Mercelis and J. P. Kruth. Rapid. Prototyping. J.12 (2006), 254.

[20] M. P. Jackson, M. J. Starink, and R. C. Reed, Mater. Sci. Eng. A., 264 (1999) 26.

[21] E.H. Vander Molen, Metal. Trans., 2 (1971) 1627.

[22] Z. Baicheng, L. Xiaohua, B. Jiaming, G. Junfeng, W. Pan, S. Chen-nan, N. Muiling, Q. Guojun, W. Jun, Mater. Design., 116 (2017), 531.

[23] P.E. Mosser, Proc. Of 6^th Int. Symp. In Metallurgy of Superalloys, Pennsylvania, (1989), 179.