Background: Assessment of dental materials do by different methods. The aim of this study was to compare the flexural strength and surface roughness of temporary crowns manufactured through conventional and digital methods.
Materials and method: An experimental laborat More
Background: Assessment of dental materials do by different methods. The aim of this study was to compare the flexural strength and surface roughness of temporary crowns manufactured through conventional and digital methods.
Materials and method: An experimental laboratory study was conducted on 60 rod-shaped samples made from three different materials. These materials were ENA high filler flowable composite, CENTRIX self-curing acrylic base composite and 3D printer resin. To create the 3D printer group samples, the original metal model was scanned and the design file was printed using a 3D printer. For the composite samples and acrylic bases, a silicone index was used, which was composed of the original metal model. Ten samples of each material were stored in artificial saliva for 30 days. The samples were then tested for flexural strength and surface roughness. The data collected was analyzed using a one-way analysis of variance, Bonferroni’s post hoc (α =0.05).
Results: The average flexural strength varied significantly among the three materials after being immersed in artificial saliva for a month (p<0.001). The ENA flow material's average flexural strength was significantly higher than the CENTRIX material and printed resin (p<0.001), and the CENTRIX material's average flexural strength was significantly higher than printed resin (p<0.001). The CENTRIX material also had a significantly higher initial roughness mean (Ra) value compared to the ENA flow material (p=0.010) and printed resin (p=0.009), while there was no significant difference between the ENA flow material and printed resin (p=1.00). One month after immersion in artificial saliva, the CENTRIX material's mean surface roughness (Ra) was significantly higher than the ENA flow material (p=0.005) and printed resin (p=0.040).
Conclusion: Flowable composite resin presents better mechanical properties when compared to acrylic base resin and printed resin. The surface roughness of flowable composite and printed resin is lower than acrylic base composite, but the surface roughness of all materials increases when exposed to saliva.
Manuscript profile
Near surface mounted (NSM) is a recent strengthening technique based on bonding carbon fiber reinforced polymer (CFRP) bars (rods or laminate strips) into pre-cut grooves on the concrete cover of the elements to strength. The corrosion or lack o More
Near surface mounted (NSM) is a recent strengthening technique based on bonding carbon fiber reinforced polymer (CFRP) bars (rods or laminate strips) into pre-cut grooves on the concrete cover of the elements to strength. The corrosion or lack of steel bars in reinforced concrete members and the resulting deterioration of structures prompted research on fiber reinforced polymers (FRP) bars as potential reinforcement for concrete members, for use in new construction. These FRP bars can be used to increase flexural and shear capacity of existing concrete members at NSM (Near Surface Mounted) method. The paper presents the details and results of the experimental and numerical programs. Two large-scale reinforced concrete beams were designed, constructed, and tested under one point concentrated loading system. The specimens had two fixed-end support. They were in same size and reinforcement characteristic. A new type of CFRP bar was proposed in this study, the CFRP bars were manually made in laboratory and were hooked at end for anchoring in concrete. The test results has been used to calibrate the analytical models. Moreover extra analytical work has done. The results indicate that FRP bars can be used effectively in existing structures to increase their flexural capacity and change their crack pattern. Photographs taken at selected stages of loading illustrated the performance of each specimen. The force-displacement was presented and compared to find efficiency of FRP bars at NSM method.
Manuscript profile
خم شدن ساقه و دمگل تحت تاثیر وزن گل یکی از مشکلات اصلی پس از برداشت در ژربرا (Gerbera jamesonii Bolus.) است و گاهی اوقات باعث شکستگی ساقه و یا اختلال در جذب آب می­شود. در این تحقیق، تیمار سیلیسیوم و اسید سالیسیلیک به منظور افزایش مقاومت مکانیکی ساقه گل استفاده شد. ن More
خم شدن ساقه و دمگل تحت تاثیر وزن گل یکی از مشکلات اصلی پس از برداشت در ژربرا (Gerbera jamesonii Bolus.) است و گاهی اوقات باعث شکستگی ساقه و یا اختلال در جذب آب می­شود. در این تحقیق، تیمار سیلیسیوم و اسید سالیسیلیک به منظور افزایش مقاومت مکانیکی ساقه گل استفاده شد. نتایج نشان داد که خمیدگی ساقه با مصرف سیلیسیوم و تیمار اسید سالیسیلیک کاهش یافت. مقاومت برشی و مقدار لیگنین توسط تیمار سالیسیلیک اسید در هر دو بخش بالا و پایین ساقه افزایش یافت. به نظر می­رسد که مقدار لیگنین ساقه با مقاومت برشی در قسمت بالایی ارتباط داشت. علاوه بر این، مقدار سیلیسیوم در بافت ساقه گل به طور قابل­توجهی با مصرف سیلیسیوم افزایش یافت و مقاومت مکانیکی قسمت پایین ساقه با میزان سیلیسیوم بافت همبستگی داشت. این نتایج نشان داد که مصرف سیلیسیوم و تیمار اسید سالیسیلیک می­تواند باعث افزایش مقاومت مکانیکی ساقه گل و بهبود کیفیت گل بریده ژربرا گردد.
Manuscript profile
Considering their suitable strength and ability to properly stabilize, metal screws are used to repair bone fractures. پیچ های فلزی به دلیل استحکام مناسب جهت ترمیم شکستگی های استخوان مورد استفاده قرار می گیرند. اما مشکلاتی چون ضریب کشسانی بالای فلزات نسبت به استخوان های More
Considering their suitable strength and ability to properly stabilize, metal screws are used to repair bone fractures. پیچ های فلزی به دلیل استحکام مناسب جهت ترمیم شکستگی های استخوان مورد استفاده قرار می گیرند. اما مشکلاتی چون ضریب کشسانی بالای فلزات نسبت به استخوان های بدن که منجر به پدیده پوکی استخوان می گردد و نیز امکان رهایش یون های فلزی در موضعی که می توان منجر به ایجاد عفونت های موضعی یا مشکلات سیستمی شود ،جایگزینی پیچ های غیر فلزی به جای انواع فلزی را در دستور کار محققین قرار داده است. در این مطالعه کامپوزیت متشکل از فاز زمینه پلیمر پلی ال-لاکتیک اسید و فاز تقویت کننده الیاف شیشه زیست فعال جهت طراحی پیچ مد نظر قرار گرفت. ابتدا ضرایب کشسانی در آنالیز میکرو تخمین زده شد سپس به آنالیز ماکرو توسط نرم افزار آباکوس 6.11 برای مدلسازی با وضعیتهای دولایهای تشکیل شده از الیاف تک جهته و رندوم (UD/R) و سه لایه ای متشکل از الیاف تک جهته ،الیاف با زاویه 20± درجه نسبت به اعمال نیرو و الیاف رندوم (UD/±20/R) با درصد های مختلف از ضخامت لایه ها انتقال داده شد. نتایج نشان داد ترکیب کامپوزیت سه لایه با درصد لایه های(25/10/65) دارای مناسب ترین پاسخ مکانیکی می باشد. در این نمونه با درصد لایه های (25/10/65) مدول خمشی 7/22 گیگا پاسکال ،استحکام خمشی 347 مگاپاسکال و ضریب کشسانی در راستای طولی 8/24 گیگا پاسکال تخمین زده شد. که مقداری از ضریب کشسانی استخوان کورتیکال بیشتر است. پیچ کامپوزیتی طراحی شده جهت تثبیت شکستگی ارتوپدی از استحکام لازم برخوردار است و به عنوان کاندیدی جهت جایگزینی پیچ های فلزی قابل استفاده است.
Manuscript profile
Sanad
Sanad is a platform for managing Azad University publications