Synthesis and characterization of hollow mesoporous Silica nanocomposites via polystyrene template

Subject Areas :

Abolhassan Najafi ¹ , Mahdi Khoeini ² , Mostafa Amani ³

1 - Islamic Azad University Saveh Branch
2 - Islamic Azad university, Saveh Branch
3 - Saveh Branch, Islamic Azad University

Received: 2019-02-05 Accepted : 2019-08-06 Published : 2020-04-20

Keywords: surfactant, Hollow mesoporous silicate particles, TEOS precursor, CTAB micelles, polystyrene template,

Abstract :

In this study, the synthesis of hollow mesoporous silicate particles was studied using TEOS precursor in the presence of a polystyrene template and CTAB surfactant micelles. The process was carried out in based on alcoholic system with pH control and adding CTAB surface activator at a suitable concentration. The results of the FTIR analysis showed that the pre-forming particles of TEOS formed surface boundaries during the synthesis process with CTAB surfactant agents. Also the presence of Si-O-Si bonds (range from 600 to 1320 cm-1) indicates the formation of silicate chains on polystyrene molds. Thermal analysis studies showed that using appropriate heat treatment and precise control, all organic compounds can be removed from the system and synthesized hollow mesoporous silica particle with the least structural defects at 380°C. The BET analysis showed that the specific surface of these synthesized mesoporous silicate particles is 1180 m2.g-1 X-ray diffraction results showed that the product obtained was amorphous silica and impurity phases are not formed in this system. The DLS analysis showed that the synthesized particles had dimensions ranging in size from 1 to 10 nm and the distribution of particle size has occurred in a narrow range. SEM images confirm the sphericality of nanoparticles with a mean size of 25-30 nm. Finally, the transmitted electron microscope images showed that the synthesized silicate particles were hollow, so that the diameter of the hollow cavity and its entire total diameter are about 30 and 80 nm, respectively.

References:

 

[1]       ن. احسانی، ح. رضایی، ف. گلستانی فرد و ا. نجفی، "ایران، سنتز و بررسی خواص پودر نانومتری سیلیکون کارباید به روش سل ژل"، فصلنامه علمی پژوهشی فرآیندهای نوین در مهندسی مواد، دوره 5، شماره 3، صفحه 11-17، پاییز 1390.

 

[2]     R. Ciriminna, A. Fidalgo, V. Pandarus, & et al., “The sol-gel route to advancedsilica-based materials and recent applications”, Chem. Rev., Vol. 113, No. 8, pp. 6592–6620, 2013.

 

[3]     W. Li, F. Wang, S. Feng, J. Wang, Z. Sun, B. Li, Y. Li, J. Yang, A. A. Elzatahry, Y. Xia & D. Zhao, “Sol–gel design strategy for ultra-dispersed TiO₂ nanoparticles on graphene for high-performance lithium ion batteries”, J. Am. Chem. Soc., Vol. 135 pp. 18300–18303, 2013.

 

[4]     B. Li, Y. Song, C. Zhang & J. Yu, “Synthesis and characterization of nanostructured silicon carbide crystal whiskers by sol–gel process and carbothermal reduction”, Ceramics International, Vol. 40, pp.  12613–12616, 2014.

 

[5]     Y. Shi, H. Li & L. Li, “Recent advances in controlled synthesis of two-dimensional transition metal dichalcogenides via vapour deposition techniques”, Chem. Soc. Rev., Vol. 44, pp. 2744-2756, 2015.

 

[6]     X. Zhuang, Y. Mai, D. Wu, F. Zhang & X. Feng, “Two-dimensional soft Nano materials: a fascinating” World of Materials, Vol. 27, pp. 403–427, 2015.

 

[7]     Maziz, C. Plesse, C. Soyer, E. Cattan & F. Vidal, “Top-down approach for the direct synthesis, patterning, and operation of artificial micro muscles on flexible substrates”, ACS Appl. Mater. Interfaces., Vol. 8, No. 3, pp. 1559–1564, 2016.

 

[8]     Y. Deng, C. Wang, J. Hu, W. Yang & S. Fu, “Investigation of formation of silica-coated magnetite nanoparticles via sol–gel approach”, Colloids and Surfaces A: Physicochemical and Engineering Aspects, Vol. 262, No. 1–3, pp. 87–93, 2005.

 

[9]     M. Toki, S. Miyashita, T. Takeuchi, S. Kanbe & A. Kochi, “A large-size silica glass produced by a new sol-gel process”, Journal of Non-Crystalline Solids, Vol. 100, No. 1–3, pp. 479-482, 1988.

 

[10] J. Li, T. Zhao, F. Li, B. Zong, Z. Du & J. Zeng, “A comparative study on the synthesis mechanism and microstructural development of hierarchical porous mullite monoliths obtained by the sol–gel process with three different silicon sources”, Ceramics International, Vol. 42, No. 4, pp. 4806–4818, 2016.

 

[11] M. Tang, X. Lin, M. Li, J. Li & S. Yin, “Construction of amperometric glucose biosensor based on in-situ fabricated hierarchical meso-macroporous SiO₂ modified Au film electrodes”, Journal of Wuhan University of Technology-Mater. Sci. Ed., Vol. 31, No. 4, pp. 736–742, 2016.

 

[12] H. Jeon, Chang S. Lee, R. Patel & J .H. Kim, “Well-organized meso-macroporous TiO₂/SiO₂ film derived from amphiphilic rubbery comb copolymer”, ACS Appl. Mater. Interfaces, Vol. 7, No. 14, pp. 7767–7775, 2015.

 

[13] E. Yu. Stovpiaga, S. A. Grudinkin, D. A. Kurdyukov, Yu. A. Kukushkina, A. V. Nashchekin, V. V. Sokolov, D. R. Yakovlev & V. G. Golubev, “Monodisperse spherical meso–macroporous silica particles: Synthesis and adsorption of biological macromolecules”, Journal of Physics of the Solid State, Vol. 58, No. 11, pp. 2339–2344, 2016.

 

[14] Najafi, F. Golestani Fard, H. R. Rezaie & N. Ehsani, “Synthesis and characterization of SiC nano powder with low residual carbon processed by sol–gel method”, Powder Technology, Vol. 219, pp. 202–210, 2012.

 

[15] B. P. Singh, J. Jena, L. Besra & S. B. hattacharjee, “Dispersion of nano-silicon carbide (SiC) powder in aqueous suspensions”, Journal of Nanoparticles Research, Vol. 9, No. 5, pp. 797–806, 2007.

 

[16]    ف. باورسی ها، م. منتظری پور، م. رجبی، س. غلامی و ن. مظفری، "سنتز و مشخصه یابی پودر کامپوزیتی TiO₂/SiO₂/SrFe₁₂O₁₉  با نانوساختار هسته/پوسته/پوسته"، فصلنامه علمی پژوهشی فرآیندهای نوین در مهندسی مواد، دوره 12، شماره 3، صفحه 137-148، پاییز 1397.

 

[17] H. Song & L. Zheng, “Nanocomposite films based on cellulose reinforced with nano-SiO₂: microstructure, hydrophilicity, thermal stability, and mechanical properties”, Cellulose, Vol. 20, No. 4, pp. 1737–1746, 2013.

 

[18] P. M. Morea, S. B. Umbarkara & M. K. Dongarec, “Template-free sol–gel synthesis of high surface area mesoporous silica based catalysts for esterification of di-carboxylic acids”, Comptes Rendus Chimie, Vol. 19, No. 10, pp. 1247–1253, 2016.

 

[19] L. Kopanja, D. Žunić, B. Lončar, S. Gyergyek & M. Tadić, “Quantifying shapes of nanoparticles using modified circularity and ellipticity measures”, Measurement, Vol. 92, pp. 252–263, 2016.

 

[20] S. Zhang, L. Wen, J. Yang, J. Zeng, Q. Sun, Z. Li, D. Zhao & S. Dou, “Facile Fabrication of Dendritic Mesoporous SiO₂-CdTe-SiO₂ Fluorescent Nanoparticles for Bioimaging”, Particle and particle systems characteristics, Vol. 33, No. 5, pp. 261–270, 2016.

 

[21]س. نقیبی، ا. جمشیدی، م. برزگر و س. رمضانی، "بررسی ریزساختاری لایه نازک تیتانیا بر روی فولاد 316 به روش سل ژل (بهینه سازی متغیرهای فرآیند با روش آماری تاگوچی)"، فصلنامه فرآیندهای نوین در مهندسی مواد، دوره 6، شماره 4، صفحه 79-89، پاییز 1391.