Numerical Simulation and the Effect of Rotational Speed on the Performance and Thickness of the Gas Film of Dry Gas Seal of the Centrifugal Compressor
Subject Areas : Journal of New Applied and Computational Findings in Mechanical SystemsNavid Bozorgan 1 , Arash Ostovari 2 , Nadia Jalalifar 3 , Moosa Ghasemi 4
1 - Department of Mechanical Engineering, Abadan Branch, Islamic Azad University, Abadan, Iran
2 - Department of Mechanical Engineering, University of Khoramshahr, Khoramshahr, Iran
3 - Department of Chemical Engineering, Abadan Branch, Islamic Azad University, Abadan, Iran
4 - Abadan oil Refinery Company
Keywords: Groove, Simulation, Dry Gas Seal,
Abstract :
In this paper, using computational fluid dynamics, the dynamic properties of the flow in the two-way grooves of a centrifugal compressor gas seal are simulated. The computational area consists of a gas film between two fixed and rotating rings and the space inside the grooves. Leak performance is tested at thicknesses of 3.08 and 5.08 μm. In order to perform the numerical solution, the continuity and Navier-Stokes equations are solved assuming complete gas using disorganized cells. The flow regime is considered layered. The results obtained include the pressure distribution. The results of numerical solution of the geometric model with bidirectional C-shaped groove were evaluated with Gabriel experimental results. Geometry discussed in this dissertation is the geometry of dry gas compressor C-14200 alkylation unit of Abadan Oil Company. The results show that the rotation speed of the Dry Gas Seal, or DGS for short, has a significant effect on the hydrodynamic effect, while the pressure of the outer radius and the thickness of the gas film both reduce the hydrodynamic effect.
[1] Muller, (1998), Fluid Sealing Technology Principles and Applications, Marcel Dekker INC.
[2] Shahin, I., Gadala, M., Alqaradawi, M., Badr, O., (2016), Three dimensional computation study for spiral drygas seal with constant groove depth and different tapered grooves. Procedia Engineering 68, pp 205-212.
[3] Jiang, J.B., Peng, X.D., Li, J.Y., Chen, Y., (2016), A comparative study on the performance of typical types of bionic groove dry gas seal based on bird wing, Journal of Bionic Engineering 13, pp 324-334.
[4] Badykov, R., Sergey, V., (2017), Advanced dynamic model development of dry gas seal, Procedia Engineering 176, pp 344 – 354.
[5] Jing, X., Peng, X., Bai, S., Meng, X., (2015), CFD simulation of microscale flow field in spiral groove dry gas seal, Proceedings of IEEE/ASME International Conference on Mechatronics and Embedded Systems and Applications (MESA).
[6] Ma, C.,Shaoxian, B., Xudong, P., (2016), Thermo-hydrodynamic characteristics of spiral groove gas face seals operating at low pressure, Tribology International 95, pp 44–54.
[7] Qiuwan, D., Keke, G., Zhang Di., Yonghui X., (2018), Effects of grooved ring rotation and working fluid on the performance of dry gas seal, International Journal of Heat and Mass Transfer 126, pp 1323–1332.
[8] Zahorulko, A.V., K., Lee, Y.B., (2021), Dynamic behavior and difference pressure control of difference pressure regulator for dry gas seals, Mechanical Systems and Signal Processing 165, 108350.
[9] Yuan, Ch., Xudong, P., Jinbo, J., Meng, X., Li, J., (2018), Experimental and theoretical studies of the dynamic behavior of a spiral groove dry gas seal at high-speeds, Tribology International 125, pp 17–26.
[10] Wang, Y., Jianjun, S.,Qiong, H., Wang, D., Zheng, X., (2018), Orientation effect of orderly roughness microstructure on spiral groove dry gas seal, Tribology International 126, pp 97-105.
[11] Liao, C., Chen, H., Lu, H., Dong, R., Sun, H., Chang, C., (2020), A leakage model for a seal-on-seal structure based on porous media method, International Journal of Pressure Vessels and Piping 188, 104227.
[12] Zhao, H., Su, H., Chen, G., (2020), Analysis of total leakage of finger seal with side leakage flow, Tribology International 150, 106371.
[13] Xie F., Li, Y., Ma Y., Xia S., Ren J., (2020), Cooling behaviors of a novel flow channel in mechanical seals of extreme high-speed rotation for cryogenic rockets, Cryogenics 107, 103055.
[14] Zhou, W., Zha, Zh., Wang, Y., Shi, J., Gan, B., Li, B., Qiu, N., (2021), Research on leakage performance and dynamic characteristics of a novel labyrinth seal with staggered helical teeth structure, Alexandria Engineering Journal 60, pp 3177-3187.
[15] Chavez A., Santiago S., (2020), Determining a pressure response function of the hose and sensor arrangement for measurements of dynamic pressure in a dry gas seal fim, Tribology International 143, 106007.
[16] Su, W.T., Li, Y., Wang, Y.H., Zhang Y.N., Li, X.B., Ma, Y., (2020), Influence of structural parameters on wavy-tilt-dam hydrodynamic mechanic al seal perfor mance in reactor coolant pump, Renewable Energy 166, pp 210-221.
[17] Zhou, X., Gu, C., Wang, J., Chen, Z., (2021), Thermo-mechanical coupling analysis of the end faces for a mechanical seal under dry friction, School of Chemical Engineering, Tribology International 160, 107050.
[18] Su, H., Rahmani, R., Rahnejat H., (2016), Thermo-hydrodynamics of bidirectional groove dry gas seals with slip flow, International Journal of Thermal Sciences 110, pp 270-284.
[19] Gabriel R., (1994), Fundamentals of spiral groove non contacting face seals, Lubrication
Engineering 50, pp 215-224.
[20] Hong, W., Baoshan, Z., Jiansh, L., Changliu, Y., (2013), A thermohydrodynamic analysis of dry gas seals for high-temperature gas-cooled reactor, Journal of Tribology 135, 021701.