Reliability and limitations of Impact-Echo Method for Thickness Measurement of Orthotropic Composite Plates

Subject Areas : Mechanical Engineering

M. Amiri ¹ , M. Tabatabaee Ghomi ² , Gh. Liaghat ³

1 - Center of Excellence in Precision Dimensional Measurement Technology Development Institute (TDI), ACECR, Sharif University Branch Tehran, Iran
2 - Center of Excellence in Precision Dimensional Measurement Technology Development Institute (TDI), ACECR, Sharif University Branch Tehran, Iran
3 - Mechanical Engineering Department Tarbiat Modares University Tehran, Iran

Received: 2017-08-07 Accepted : 2017-10-15 Published : 2018-02-18

Keywords:

References:

[1]     ASTM D 4580-86. Standard practice for measuring delaminations in concrete bridge decks by sounding, Annual book of ASTM standards, Vol. 04. 03. Philadelphia: ASTM, 1987. pp. 749-51.

[2]     Khalili, S. M. R., Eslami Farsani, R., and Daghigh, V., “Aging Influence on Charpy Impact Behaviour of Basalt Fibre Reinforced Epoxy Composites”, Int J of Advanced Design and Manufacturing Technology, Vol. 6, No. 2, 2013, pp. 81-85.

[3]     Ferna´ndez-Cantelia, A., Argu¨ellesa, A., Vina, J., Ramulub, M., and Kobayashib, A. S., “Dynamic Fracture Toughness Measurements in Composites by Instrumented Charpy Testing: Influence of Aging”, Composite Science & Technology, Vol. 62, 2002, pp. 1315-1325.

[4]     Khalili, S. M. R., Daghigh, V., and Eslami Farsani, R., “Mechanical Behavior of Basalt Reinforced and Basalt Fiber Metal Laminate Composites Under Tensile and Bending Loads”, Journal of Reinforced Plastics and Composites, Vol. 30, 2011, pp.647-659.

[5]     Khazraiyan, N., Dashtian Gerami, N., Damircheli, M., “Numerical Simulation of Fluid-Structure Interaction and its Application in Impact of Low Velocity Projectiles with Water Surface”, Int J of Advanced Design and Manufacturing Technology, Vol. 8, No. 2, 2015, pp. 81-90.

[6]     Fairlie-Clarke, A. C., Tveitnes, T., “Momentum and Gravity Effects During the Constant Velocity Water Entry of Wedge-Shaped Sections”, Ocean Engineering, Vol. 37, No. 5, 2008, pp. 706-716.

[7]     Habibalahi, A., Safizadeh, M. S., “Application of Pulsed Eddy Current Technique in Stress and Residual Stress Measurement”, Int. J of Advanced Design and Manufacturing Technology, Vol. 7, No. 1, 2014, pp. 67-74.

[8]     Blodgett, M. P., Nagy, P. B., “Eddy Current Assessment of Near-Surface Residual Stress in Shot Peened Nickel Base Superalloys”, Journal of nondestructive evaluation, Vol. 23, 2004, pp. 107-123.

[9]     Wilson, J. W., Tian, G. Y., and Barrans, S., “Residual Magnetic Field Sensing for Stress Measurement”, Sensors and actuators A, Vol. 135, 2007, pp. 381-387.

[10]  Hughes, D. S., Kelly, J. L., “Second Order Elastic Deformation of Solids”, Physical review, Vol. 92, 1953, pp. 1145-1149.

[11]  Langman, R. A., Mutton, P. J., “Estimation of Residual Stresses in Railway Wheels by Means of Stress Induced Magnetic Anisotropy”, NDT & E International, Vol. 26, 1993, pp. 195-205.

[12]  Wang, P., Zhu, L., Zhu, J., Ji, L., Wang, T., Tian, G., and Yao, E., “An Application of Back Propagation Neural Network for the Steel Stress Detection Based on Barkhausen Noise Theory”, NDT & E International, Vol. 55, 2013, pp. 9-14.