Numerical Analysis of The Crater Diameter and Penetration Depth of The Target Due to The Impact of Short-Rod Segmented Projectiles at High Velocity

الموضوعات :

Behnam Yasemi ¹ , Hamid Soleimanimehr ² , Hossein Khodarahmi ³ , sadegh rahmati ⁴ , Najmeh khazraiyan ⁵

1 - Department of mechanical engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
2 - Department of mechanical engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
3 - Department of Mechanical Engineering, Imam Hossein University, Tehran, Iran
4 - Faculty of Medical Sciences and Technologies, Science and Research Branch, Islamic Azad University, Tehran, Iran
5 - Engineering faculty, Islamshahr Branch, Islamic Azad University, Tehran, Iran

تاريخ الإرسال : 07 الخميس , شعبان, 1443 تاريخ التأكيد : 22 الخميس , ذو الحجة, 1443 تاريخ الإصدار : 05 الخميس , صفر, 1444

الکلمات المفتاحية: SPH, Segmented Projectile, numerical simulation, Aspect Ratio,

ملخص المقالة :

This paper deals with the numerical simulation of segmented projectiles. A segmented projectile is a subset of kinetic energy projectiles. The segmented projectile is made of tungsten and the target is semi-infinite and is made of 4340 steels. Due to the disadvantages of segmented projectiles with, the simulation of segmented projectile with is discussed. Projectiles with aspect ratio greater than one are known as short-rod projectiles. This aspect ratio range forms both the primary and secondary phase of penetration. Numerical simulation was performed by AUTODYN software with Smoothed Particle Hydrodynamic (SPH) method. The use of SPH approach is most consistent with the experimental results. In order to have effective segmented projectiles, greater speeds were used in the simulations. In this range of velocity, due to the hydrodynamic penetration and complete erosion of the rods, the maximum penetration depth is obtained. After a relatively good correlation between the simulation results and the experimental and Hydrocode results, the numerical analysis of the segmented projectiles is performed. The results show an increase in the penetration depth of segmented projectile relative to the continuous type. In the following, the relationship between velocity increase and penetration depth and crater diameter of this type of projectile is investigated. An increase in penetration depth of 40 to 60% has been observed in this type of projectile compared to the continuous projectiles. An increase in penetration depth and crater diameter is observed with increasing impact velocity.

المصادر:

• Zukas, J. A., High Velocity Impact Dynamics, 1st ed, John Wiley&Sons, New York, 1990, pp. 431-433.


• Franzen, R. R., Walker, J. D., Orphal, D. L., and Anderson, C. E., An upper Limit for The Penetration Performance of Segmented Rods with Segment-L/D 1, International Journal of  Impact Engineering, Vol. 15, No. 5, 1994, pp. 661-668.


• Naz, P., Lehr, H., the Crater Formation Due to Segmented Rod Penetrators, International Journal of Impact Engineering, Vol. 10, 1990, pp. 413-425.


• Christman, D., Gehring, J., Analysis of High Velocity Projectile Penetration Mechanics, Journal of Applied Physics, Vol. 37,1966, pp. 1579-1587, DOI. 10.1063/1.1708570.


• Lee, M., Normandia, M. J., Successive Impact of Segmented Rods at High-Velocity, KSME International Journal, Vol. 13, No. 4, 1999, pp. 312-320.


• Holland, P. M., Gordon, J. T., Menna, T. L., and Charters, A. C., Hydrocode Results for The Penetration of Continuous, Segmented and Hybrid Rods Compared with Ballistic Experiments, International Journal of Impact Engineering, Vol. 10, 1990, pp. 241-250.


• Mchenry, M. R., Choo, Y., and Orphal, D. L., Numerical Simulations of Low L/D Rod Aluminum into Aluminum Impacts Compared to The Tate Cratering Model, International Journal of Impact Engineering, Vol. 23,1999, pp. 621-628.


• Lee, M., A Numerical Comparison of The Ballistic Performance of Unitary Rod and Segmented-Rods Against Stationary and Moving Oblique Plates, International Journal of Impact Engineering, Vol. 26, 2001, pp. 399-407.


• Aly, S., Li Q., Numerical Investigation of Penetration Performance of Non-Ideal Segmented-Rod Projectiles. Transactions of Tianjin University, Vol. 14, 2008, pp. 391-395, DOI 10.1007/s12209-008-0067-x.


• Wang, X., Zhao, G., High Velocity Impact of Segmented Rods with An Aluminum Carrier Tube, International Journal of Impact Engineering, Vol. 17, 1995, pp. 915-923.


• Hegde, G. S., Narasimha, Murthy H. N., and Krishna, M., The Analytical Study on The Optimal Ballistic Performance Using Interface Theory, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 41, 2010, pp. 112-123.


• Cao, Z. S., Deng, Y. F., and Zhang, W., Numerical Investigation of Penetration Performance of Segmented Rod Projectiles with Various Connectors, in Key Engineering Materials, Vol. 452-453, 2011, pp. 185-188, doi:10.4028/www.scientific.net/KEM.452-453.185.


• Presnell, M. B., Rajendran, A. M., A Computational Study of Segmented Tungsten Rod Penetration into A Thick Steel Target Plate at High Velocities, in AIP Conference Proceedings, 2012, American Institute of Physics, https://doi.org/10.1063/1.3686226.


• Zolfaghari, M., Miraghaie, V., A New Mathematical Model for The Penetration of Segmented Rod into Ceramic Semi-Infinite Target, Journal of Energetic Materials, 12, No. 1, 2017, pp. 55-67


• Arjangi, A., Soleimanimehr, H., and Mirzaei, M., Simulation of Rock Drilling Process Using Smoothed-Particle Hydrodynamics Method, Advanced Journal of Science and Engineering, Vol. 1, 2020, pp. 52-58, DOI: 10.22034/AJSE.2012052.


• Hedayati, E., Vahedi, M., Numerical Investigation of Penetration in Ceramic/Aluminum Targets Using Smoothed Particle Hydrodynamics Method and Presenting a Modified Analytical Model, Computer Modeling in Engineering & Sciences, Vol. 113, No. 3, 2017, pp. 295-323.


• Frissane, H., Taddei, L., Lebaal, N., and Roth, S., 3D Smooth Particle Hydrodynamics Modeling for High Velocity Penetrating Impact Using GPU: Application to a Blunt Projectile Penetrating Thin Steel Plates, Computer Methods in Applied Mechanics and Engineering, Vol. 357, 2019, https://doi.org/10.1016/j.cma.2019.112590.


• Giannaros, E., Kotzakolios, A., Kostopoulos, V., and Campoli, G., Hypervelocity Impact Response of CFRP Laminates Using Smoothed Particle Hydrodynamics Method: Implementation and Validation, International Journal of Impact Engineering, Vol. 123, 2019, pp. 56-69, https://doi.org/10.1016/j.ijimpeng.2018.09.016.


• Liu, M., Liu, G., Smoothed Particle Hydrodynamics (SPH): an Overview and Recent Developments, Archives of computational methods in engineering, Vol. 17, 2010, pp. 25-76, DOI. 10.1007/s11831-010-9040-7.


• Bonet, J., Lok, T. S. L., Variational and Momentum Preservation Aspects of Smooth Particle Hydrodynamic Formulations, Computer Methods in applied mechanics and engineering, Vol. 180, 1999, pp. 97-115, https://doi.org/10.1016/S0045-7825(99)00051-1.


• Biniyazan F, Soleimanimehr H., Improving both strength and ductility of Al-7075 by combining dual equal channel lateral extrusion with aging heat treatment, Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, Vol. 45, 2021, pp. 727-739,https://doi.org/10.1007/s40997-020-00416-y.