Direct Kinematics Solution of 3-RCC Parallel Robot using a Semi-Analytical Homotopy Method
الموضوعات :Seyyed Mojtaba Varedi-Koulaei 1 , Masoumeh Rahimi 2
1 - Department of Mechanical and Mechatronics Engineering,
Shahrood University of Technology, Iran
2 - Department of Mechanical Engineering, Faculty of Engineering,
Golestan University, Iran
الکلمات المفتاحية: Parallel Manipulator, Numerical Methods, Homotopy Continuation Method, Nonlinear Equations, Direct Kinematics,
ملخص المقالة :
Parallel robots are closed-loop mechanisms presenting very good performances in terms of accuracy, rigidity, and the ability to manipulate large loads. Inverse kinematics problem for most parallel robots is straightforward, while the direct kinematics is not. The latter requires the solution of the system of nonlinear coupled algebraic equations and has many solutions. Except in a limited number of these problems, there is difficulty in finding exact analytical solutions. So these nonlinear simultaneous equations should be solved using some other methods. Continuation or path-following methods are standard numerical techniques to trace the solution paths defined by the Homotopy. This paper presents the direct kinematics solutions for a 3RCC parallel robot by using a semi-analytical Homotopy method called Homotopy Continuation Method (HCM). The HCM has some advantages over the conventional methods and alleviates drawbacks of the traditional numerical techniques, namely; the acquirement of good initial guess values, the problem of convergence and computing time. The direct kinematic problem of the 3RCC parallel robot leads to a system of nonlinear equations with 9 equations and 9 unknown parameters. The proposed method solved these nonlinear equations and extracted all the 36 solutions. Results indicate that this method is effective and reduces computation time in comparison with the Newton–Raphson method.
[1] Gough, V. E., Whitehall, S. G., Universal Tire Test Machine, in: Proceedings of 9th International Technical Congress, F.I.S.I.T.A., Vol. 177, 1962.
[2] Stewart, D. A., Platform with Six Degrees of Freedom, in: Proceedings of the Institute of Mechanical Engineering, Vol. 180, No. 5, 1965, pp. 371–386.
[3] Hunt, K. H., Kinematic Geometry of Mechanism, Clarendon Press, Oxford, 1978.
[4] Fichter, E. F., A Stewart Platform-Based Manipulator: General Theory and Practical Construction, International Journal of Robotics Research, Vol. 5, No. 2, 1986, pp. 157–182.
[5] Mohammadi Daniali, H. R., Zsombor Murray, P. J., and Angeles, J., Singularity Analysis of Planar Parallel Manipulators, Mechanism and Machine Theory, Vol. 30, No. 5, 1995, pp. 665–678.
[6] Merlet, J. P., Gosselin, C. M., and Mouly, N., Workspaces of Planar Parallel Manipulators, Mechanism and Machine Theory, Vol. 33, No. 1–2, 1998, pp. 7–20.
[7] Tsai, M. S., Shiau, T. N., Tsai, Y. J., and Chang, T. H., Direct Kinematic Analysis of a 3-PRS Parallel Mechanism, Mechanism and Machine Theory, Vol. 38, No. 1, 2003, pp. 71–83.
[8] Korayem, M. H., Bamdad, M., Dynamic Load- Carrying Capacity of Cable- Suspended Parallel Manipulators, International Journal of Advance Design and Manufacturing Technology, Vol. 44, 2008, pp. 829–840.
[9] Varedi Koulaei, S. M., Daniali, H. M., Farajtabar, M., Fathi, B., and Shafiee Ashtiani, M., Reducing the Undesirable Effects of Joints Clearance on the Behavior of the Planar 3-RRR Parallel Manipulators, Nonlinear Dynamics, Vol. 86, 2016, pp. 1007–1022.
[10] Shahabi, E., Hosseini, M. A., Kinematic Synthesis of a Novel Parallel Cable Robot as the Artificial Leg, International Journal of Advance Design and Manufacturing Technology, Vol. 9, No. 3, 2016, pp. 1-10.
[11] Varedi, S. M., Daniali, H. M., and Dardel, M., Dynamic Synthesis of a Planar Slider-Crank Mechanism with Clearances, Nonlinear Dynamics, Vol. 79, 2015, pp. 1587–1600.
[12] Dasgupta, B., Mruthyunjaya, T. S., The Stewart Platform Manipulator: a Review, Mechanism and Machine Theory, 35, 2000, pp. 15–40.
[13] Bonev, I. A., Ryu, J., A New Method for Solving the Direct Kinematics of General 6-6 Stewart Platforms, Mechanism and Machine Theory, Vol. 35, 2000, pp. 423–436.
[14] Kachapi, S. H. A., Ganji, D. D., Davodi, A. G., and Varedi, S. M., Periodic Solution for Strongly Nonlinear Vibration Systems by He's Variational Iteration Method, Mathematical Methods in the Applied Sciences, Vol. 32, No. 18, 2009, pp. 2339-2349.
[15] He, J. H., Variational Iteration Method–a Kind of Non-Linear Analytical Technique: Some Examples, International journal of Non-Linear Mechanics, Vol. 34, 1999, pp. 699–708.
[16] He, J. H., A Coupling Method of a Homotopy Technique and a Perturbation Technique for Non-Linear Problems, International Journal of Non-Linear Mechanics, Vol. 35, 2000, pp. 37–43.
[17] Wu, T. M., A Study of Convergence on the Newton- Homotopy Continuation Method, Applied Mathematics and Computation, Vol. 168, 2005, pp. 1169–1174.
[18] Wu, T. M., The Inverse Kinematics Problem of Spatial 4P3R Robot Manipulator by the Homotopy Continuation Method with an Adjustable Auxiliary Homotopy Function, Nonlinear Analysis, Vol. 64, 2006, pp. 2373–2380.
[19] Morgan, A. P., Wampler, C. W., Solving a Planar Four-Bar Design Problem Using Continuation, ASME Journal of Mechanism Design, Vol. 112, 1990, pp. 544 –550.
[20] Garcia, C. B., Zangwill, W. I., Pathways to Solutions, Fixed Points, and Equilibria, Prentice-Hall Book Company, Inc., Englewood Cliffs, New Jersey, 1981.
[21] Allgower, E. L., Georg, K., Numerical Continuation Methods, An Introduction, Springer, NewYork, 1990.
[22] Varedi, S. M., Daniali, H. M., and Ganji, D. D., Kinematics of an Offset 3-UPU Translational Parallel Manipulator by the Homotopy Continuation Method, Nonlinear Analysis: Real World Applications, Vol. 10, 2009, pp.1767–1774.
[23] Tari, H., Su, H. J., and Li, T. Y., A Constrained Homotopy Technique for Excluding Unwanted Solutions from Polynomial Equations Arising in Kinematics Problems, Mechanism and Machine Theory, Vol. 45, No. 6, 2010, pp. 898–910.
[24] Tari, H., Su, H. J., A Complex Solution Framework for the Kinetostatic Synthesis of a Compliant Four-Bar Mechanism, Mechanism and Machine Theory, Vol. 46, No. 8, 2011, pp. 1137–1152.
[25] Shen, H., Yang, T., Tao, S., Liu, A., and Ma, L. Z., Structure and Displacement Analysis of a Novel Three-Translation Parallel Mechanism, Mechanism and Machine Theory, Vol. 40, 2005, pp. 1181–1194.
