journal of Artificial Intelligence in Electrical Engineering: 5 (27)

Open Access Article

1 - A Comparison between OTC and P&O MPPT Control Methods Applied to Small Sized Wind Power Plants
Shirmohammadi ramin Ali ajami

This paper provides a review of OTC and P&O MPPT controllers used for extracting maximum power from the wind energy systems using permanent magnet synchronous generators. Hence, the output power of wind energy system varies continually as wind speed changes, it is d More

This paper provides a review of OTC and P&O MPPT controllers used for extracting maximum power from the wind energy systems using permanent magnet synchronous generators. Hence, the output power of wind energy system varies continually as wind speed changes, it is desirable to determine the one optimal generator speed that ensures maximum energy yield. Thus, it is important to include a controller that can track the maximum peak regardless of wind speed. After explaining the basic concepts of OTC and P&O algorithms by implementing the algorithms on MATLAB -SIMULINK platform, a comparison has been made between the performance of these two MPPT algorithms on the basis of speed responses and ability to achieve the maximum energy. The priority of OTC algorithm is validated through analyzing simulation results Manuscript profile

Open Access Article

2 - Using New Techniques and Devices within the Set of Tiba Body Roller Hamming Robots
Hamidreza Valizadeh Keivan Gharbanian Alireza Nourinejhad

In this article, new techniques and technologies have been tried and tested in the installation and commissioning of Roller Home industrial robots, in order to produce a Tiba car with a focus on cost reduction. Due to the fact that press equipment for automobile parts r More

In this article, new techniques and technologies have been tried and tested in the installation and commissioning of Roller Home industrial robots, in order to produce a Tiba car with a focus on cost reduction. Due to the fact that press equipment for automobile parts requires a lot of expenses, it was decided to use robots with the same function of roller to reduce costs and increase the quality and increase the product variety. The Hamming roller robot can flexure the single-layer and multi-layer sheets, according to its structure and advantages, and then with a suitable and variable pressure at any point. To reduce the cost using the Devicenet network of Hamming roller robots in The production of the TB vehicle as a carrier carrier has also been used, which has reduced the cable, connectible equipment and carrier robots. Manuscript profile

Open Access Article

3 - Appropriate Roadside UnitsPlacement in VANET Networks to Reduce Data Transfer Time
zinat Salehikiaa MohammadReza Salehnamadi

VANETs, as a subset of the MANETs, have progressed remarkably in recent years. These networks have an important role in improving traffic, road safety and driver service. In vehicle Networks, vehicle can Communication by vehicle-to-vehicle communication. Since there are More

VANETs, as a subset of the MANETs, have progressed remarkably in recent years. These networks have an important role in improving traffic, road safety and driver service. In vehicle Networks, vehicle can Communication by vehicle-to-vehicle communication. Since there are fewer vehicles in the environment, there is no vehicle-to-vehicle connection in some areas. Therefore, they use Road Side Units (RSUs) alongside vehicles to send and receive information. Roadside equipment, in addition to information dissemination, has a significant impact on communication, routing and transmission with minimal delay. The efficiency of a VANETs dramatically depends on the density, position and coverage of these units. Because of the high cost of installing and maintaining roadside units, there is no way to cover the entire environment, so we need to install them in places that will save costs and reduce the time needed to transfer information, in addition to reducing costs. The purpose of this paper is to target the minimum number of roadside units in the urban area, so that messages can be transmitted to the roadside units within the range of delayed emissions. In this research, a delay analysis is presented in urban environments, and based on this analysis, the RSU Optimization Placement problem is solved with greedy algorithm and imperialist competitive algorithm. Simulation results show that this roadside installation pattern has improved network performance and reduced cost Manuscript profile

Open Access Article

4 - Designing a Multiband Multi Polarization BTS Antenna
amir bakhshi ali pourziad

In this paper, a new antenna is presented which has an application in cellular telecommunication systems. The designed antenna works at the frequency range of 1900-2600 MHz which is able to cover 2G, 3G and 4G (LTE) services of the cellular telecommunication. In this pa More

In this paper, a new antenna is presented which has an application in cellular telecommunication systems. The designed antenna works at the frequency range of 1900-2600 MHz which is able to cover 2G, 3G and 4G (LTE) services of the cellular telecommunication. In this paper, the micro-strip structure has been used to design the antenna. The shape of the patches is triangular where a peripheral ring has been employed around the patches. A number of slots have been used over patch to increase the antenna efficiency. The obtained bandwidth for VSWR<2 is 56%. The antenna gain has been obtained within the frequency range of above 15 dB performance. The compressed dimensions, having two orthogonal polarization and simple antenna feed are considered as the advantages of the designed antenna. Manuscript profile

Open Access Article

5 - Planning Arm with 5 Degrees of Freedom for Moving Objects Based on Geometric Coordinates and Color
Vadoud Asadi

Skilled mechanical arms of consanguine relationship formed by joints the relative motion of the adjacent interfaces enable, have been connected. Ability to perform a variety of pre-programmed robotic manipulator in various industries. Skilled mechanical arms in recent y More

Skilled mechanical arms of consanguine relationship formed by joints the relative motion of the adjacent interfaces enable, have been connected. Ability to perform a variety of pre-programmed robotic manipulator in various industries. Skilled mechanical arms in recent years as a significant progress has been completed. House repair and easier to work with them as well and fit and optimal relationship between power, controllability and skill building. In this respect, there are a variety of skilled mechanical arms and a wide variety of different industrial applications and also to cover investigative. These applications perform various activities including construction, underwater cutting and welding production lines to perform various operations - such as the installation of underwater robots - such as the pursuit of a cable or wire, or locked objects in complex samples such as establishing connections or electrical or hydraulic lines .The mechanical arms that what matters is the simplest example may be assigned to duty at the desired time to do the selection. Robot design complexity while increasing performance capabilities can be difficult to control, guidance and ensuring the accuracy and maintenance of the cause. Selection and completion of the complex and sophisticated robotic manipulator robot designer should consider the many points. Number of arms required, location, type of controller, the access point and the maximum and minimum access point, space and arms control by the user, including the following. Manuscript profile

Open Access Article

6 - License Plate location Determination by Using Case-Based Reasoning
yaser ebadzadeh Ahmad Habibi Zad Navin

The license plate recognition system is part of the intelligent transportation system. In the intelligent transportation system, the vehicle image is used as the system input. The first step is to improve the image, after the edge detection, a series of morphological op More

The license plate recognition system is part of the intelligent transportation system. In the intelligent transportation system, the vehicle image is used as the system input. The first step is to improve the image, after the edge detection, a series of morphological operations are performed to identify the plaque. The main purpose of this research was to increase the importance of plate recognition in unusual conditions, such as color change of the plaque, which is used to achieve this case-based reasoning adaptive power. The results showed that the proposed method has had an accuracy level of 84.5% plaque recognition and it was more accurate than the existing systems. Manuscript profile

XML

List of Articles