Investigation of Compressive Stresses of Stainless Steel 316L Diamond Lattice Structures Under the Effect of Spherical Connections Produced by SLM Additive Manufacturing

Subject Areas : additive manufacturing

Behnam Ahmadi Roozbahani ¹ , AliAkbar Lotfi Neyestanak ²

1 - Department of Mechanical Engineering,Shahr-e-Qods Branch. Islamic Azad University, Tehran, IranMapna Group, TUGA, Tehran, IranE-mail: [e-mail]
2 - Department of Mechanical Engineering, Yadegar-e-Imam Khomeini (RAH), Shahr-e-Ray Branch. Islamic Azad University, Tehran, Iran E-mail: [e-mail]

Received: 2022-08-29 Accepted : 2023-12-01 Published : 2024-02-24

Keywords: Spherical Connections, Stainless steel 316L, Additive Manufacturing, Lattice structures, Compressive Stresses,

Abstract :

In this study, the compressive stresses of dodecahedron diamond lattice structures have been investigated. The finite element method has been used for Stress analysis. After the simulation, it was found that more stresses are applied at the junction of the struts of this structure due to the application of compressive force. For this purpose, the connection point of the structure’s struts was strengthened by spherical connections, and a new type of dodecahedron structure was created. The validation and effect of spherical connections in compressive stresses have been evaluated experimentally. Two types of diamond lattice structures are made of stainless steel 316L by the SLM method. The results show that in the same condition, the use of spherical connections with twice the diameter of the structure’s struts helps to strengthen the structure and increase its compressive strength by 18% compared to the simple structure.

References:

[1] Tobias, M., Martin, L., Bill, L., Xuezhe, Zh., Ma, Q., Omar, F., and Milan, B., SLM Lattice Structures: Properties, Performance, Applications and Challenges, 10.1016/J.MATDES.2019.108137, 2019.
[2] Long, B., Junfang, Zh., Xiaohong, Ch., Changyan, Y, Rui, Ch., and Zixiang, Zh.,. Configuration Optimization Design of Ti6Al4V Lattice Structure Formed by SLM, 10.3390/ma11101856, 2018.
[3] Doruk, G., Binnur, S., Additive Manufactured Ti6Al4V Lattice Structures for Biomedical Applications, Vol. 5, No. 2, 2021, pp. 155-163, 31.08.2021.
[4] M. Ashby., The Properties of Foams and Lattices, Philosophical Transactions of the Royal Society, Vol. 364, 2005, pp. 15.
[5] Paweł, P., Judyta, S., Jacek, J., and Fengchun, J., Investigations on Mechanical Properties of Lattice Structures with Different Values of Relative Density Made from 316L by Selective Laser Melting (SLM), Materials, Vol. 13, No. 9, 2020, pp. 2204.
[6] Morrish, S. J. N., Pedersen. M., Wong, K. F. W., Todd, I., and Goodall, R., Size Effects in Compression in Electron Beam Melted Ti6Al4V Diamond Structure Lattices, Mater. Lett., Vol. 190, 2017, pp. 138–142.
[7] Sarah, N. M. J., Mechanical Properties and Structural Evaluation of Diamond Structure Ti6Al4V Lattices Made by Electron Beam Melting, A Thesis Presented for The Degree of Doctor of Philosophy, Department of Materials Science and Engineering the University of Sheffield, 2017
[8] Hakan, B., Jonas, S., Mechanical Properties of Lattice Truss Structures Made of a Selective Laser Melted Superalloy, 13th International Conference on Fracture, Beijing, China., 2013.
[9] Hasanain, A., Designing New Generations of BCC Lattice Structures and Developing Scaling Laws to Predict Compressive Mechanical Characteristics and Geometrical Parameters, A thesis presented for the degree of degree of Doctor of Philosophy in Wright State University, 2020.
[10] V. Salarvand, V., SohrabpoorH., Mohammadi, M. A., Nazai, M., Raghavendra, R., Mostafaei, A., and Brabazon, D., Microstructure and Corrosion Evaluation of As-Built and Heat-Treated 316l Stainless Steel Manufactured by Laser Powder Bed Fusion, 10.1016/j.jmrt.2022.03.156, 2022.
[11] Manuel, G., Lizangela, G., Barbara, B., Roberto, C., and Luis, R., Characterization of Sio2-Tio2 Coatings on 316L Stainless Steel Substrates, L. Reyes et al, Journal of Advanced Materials and Processing, Vol. 6, No. 1, 2018, pp. 3-13
[12] ASTM, Standard E-8, Standard Test Methods for Tension Testing of Metallic Materials.
[13] Pengfei, Zh., Ran, Ch., Haiting, L., Jiming, Ch., Zhijie, Zh., Xing, L., and Yao, Sh., On the Standard and Practices for Miniaturized Tensile Test-A Review, 10.1016/j.fusengdes.2020.112006.
[14] Ushijima, K., Cantwell, W., Mines, R., Tsopanos, S., and Smith, M., An Investigation into The Compressive Properties of Stainless-Steel Micro-Lattice Structures, Journal of Sandwich Structures and Materials, Vol. 13, No. 3, 2011, pp. 303-329.
[15] TUGA Technical Review, First MGT-30 Gas Turbine Additively Manufactured Parts Set to Render Conventional Manufacturing Process of The Part Obsolete, No. 16, 2021.