List of Articles Machining

• Open Access Article
  • Abstract Page
  • Full-Text
  
  1 - Investigation of Parameters Affecting Surface Integrity and Material Removal during Electrical Discharge Machining of HARDOX-400 Steel
  Hesam Motevasseli Ahmad Afsari Ali Khosravifard
  20.1001.1.27170314.2020.9.2.6.0
• Open Access Article
  • Abstract Page
  • Full-Text
  
  2 - An Investigation on the Effect of Acidithiobacillus Ferrooxidans Bacteria on Biomachining of Titanium Alloy and Copper
  Mehrdad Ghani Hamid Soleimanimehr Elham Shirani Bidabadi
  20.1001.1.27170314.2020.9.1.2.4
• Open Access Article
  • Abstract Page
  • Full-Text
  
  3 - Imperialist Competitive Algorithm (ICA) Approach for Optimization of the Surface Grinding Process
  Ahmad Afsari Mohammad Ramezani Shahin Heidari Jafar Karimi
  20.1001.1.27170314.2020.9.1.5.7
• Open Access Article
  • Abstract Page
  • Full-Text
  
  4 - Experimental Study of Germanium Dry Machining with Various Rake Angles and Different Feed Rates of Tool
  Mohammad Reza Safavipour Masoud Farahnakian
  20.1001.1.27170314.2021.10.1.5.4
• Open Access Article
  • Abstract Page
  • Full-Text
  
  5 - Experimental Study of the Effect of Different Spindle Speeds and Feed Rates in Dry Machining on a Brittle Material
  Mohammad Reza Safavipour Masoud Farahnakian
  20.1001.1.27170314.2021.10.4.4.9
• Open Access Article
  • Abstract Page
  • Full-Text
  
  6 - Investigation of the Impact of the Alumina Powder Presence in Dielectric on Electrical Discharge Machining Parameters of A413 Aluminum Workpiece using Taguchi's Experiment Design, Signal-to-noise Analysis, and Total Normalized Quality Loss
  Mojtaba Shahbazi Dastjerdi Ali Mokhtarian Mojtaba Rahimi
  20.1001.1.27170314.2023.12.1.6.9
• Open Access Article
  • Abstract Page
  • Full-Text
  
  7 - Machining Operation Parameters in Drilling Process; Variation of Thrust Forces in Epoxy Based Nanocomposites
  Hamzeh Shahrajabian Masoud Farahnakian Mehdi Moghri
  20.1001.1.27170314.2016.5.3.1.9
• Open Access Article
  • Abstract Page
  • Full-Text
  
  8 - A Novel Optimization Approach Applied to Multi-Pass Turning Process
  Amin Kolahdooz Hossein Towsyfyan Seyed Adnan Adnani Salehi Majed Ghayyem Farid Mosaedi
  20.1001.1.27170314.2017.6.2.1.4
• Open Access Article
  • Abstract Page
  • Full-Text
  
  9 - Machinability evaluation of Titanium alloy in Laser Assisted Turning
  Kamran Puladsaz Razavi Shojae Rezavi Mehdi Tajaddara
  20.1001.1.27170314.2013.2.3.2.9
• Open Access Article
  • Abstract Page
  • Full-Text
  
  10 - Experimental Investigation of the Effect of Deionized Water on Surface Roughness of Near Dry Electro Discharge Machining of AISI D2 Steel
  Mojtaba Taghizadeh Sayed Ali Mosavi
  20.1001.1.27170314.2016.5.2.2.8
• Open Access Article
  • Abstract Page
  • Full-Text
  
  11 - Intelligent Knowledge Based System Approach for Optimization of Design and Manufacturing for Abrasive Water Jet Machining
  Morteza Sadegh Amalnik
  20.1001.1.27170314.2015.4.2.2.1
• Open Access Article
  • Abstract Page
  • Full-Text
  
  12 - Micro Machining of AISI 440C Stainless Steel using Magnetic Field and Magnetic Abrasive Particles
  Yahya Choopani Mohammad Reza Razfar
  20.1001.1.27170314.2014.3.2.2.4
• Open Access Article
  • Abstract Page
  • Full-Text
  
  13 - Intelligent Knowledge Based System Approach for Optimization of Design and Manufacturing Process for Wire-Electrical Discharge Machining
  Morteza Sadegh Amalnik
  20.1001.1.27170314.2015.4.1.3.0
• Open Access Article
  • Abstract Page
  • Full-Text
  
  14 - Numerical/Experimental Analysis of the Deformation of Tubes under Concentrated Load
  Javad Jafari Fesharaki Omid Rejali Seyed Ghasem Madani
  20.1001.1.27170314.2017.6.3.2.7
• Open Access Article
  • Abstract Page
  • Full-Text
  
  15 - The Analysis of Experimental Process of Production, Stabilizing and Measurement of the Thermal Conductivity Coefficient of Water/Graphene Oxide as a Cooling Nanofluid in Machining
  Ramin Ranjbarzadeh Amir Homayoon Meghdadi Mohammad Hojaji
  20.1001.1.27170314.2016.5.2.5.1
• Open Access Article
  • Abstract Page
  • Full-Text
  
  16 - An Experimental Investigation on Surface Roughness and Edge Chipping in Micro Ultrasonic Machining
  Hamid Zarepour
  20.1001.1.27170314.2016.5.4.5.5
• Open Access Article
  • Abstract Page
  • Full-Text
  
  17 - Development of Design and Manufacturing Support Tool for Optimization of Ultrasonic Machining (USM) and Rotary USM
  Morteza Sadeghamalnik Mohammad Rasoul Najafi
  20.1001.1.27170314.2014.3.2.6.8
• Open Access Article
  • Abstract Page
  • Full-Text
  
  18 - Controlling Electrochemical Machining By Using a Fuzzy Logic Approach
  Morteza Sadegh Amalnik
  20.1001.1.27170314.2017.6.2.5.8
• Open Access Article
  • Abstract Page
  • Full-Text
  
  19 - Experimental Study of the Cutting Parameters Effect on Hole Making Processes in Hardened Steel
  Navid Molla Ramezani Mojtaba Rezaei Hajideh Ali Shahmirzaloo
  20.1001.1.27170314.2017.6.3.5.0