تأثیر زمان اتصال بر ریزساختار و تکمیل انجماد ایزوترم در خلال اتصال TLP سوپر آلیاژهای پایه نیکل غیرمشابه IN738LC و Nimonic 75
محورهای موضوعی : روش ها و فرآیندهای نوین در تولیدمیثم خاکیان قمی 1 , محمد سعید شهریاری 2 , سعید ناطق 3
1 - دکتری مهندسی مواد و متالورژی، مدیر مهندسی بازسازی شرکت مهندسی موادکاران- مپنا، کرج، ایران.
2 - کارشناس ارشد مهندسی مواد و متالورژی، مدیر مهندسی بازسازی قطعات هوایی شرکت مهندسی موادکاران- مپنا، کرج، ایران.
3 - استاد، دانشگاه آزاد اسلامی، واحد علوم و تحقیقات، دانشکده مهندسی مواد و متالورژی، تهران، ایران.
کلید واژه: ریزساختار, سوپرآلیاژ نایمونیک 75 و اینکونل 738, اتصال TLP, انجماد ایزوترم,
چکیده مقاله :
اتصال سوپر آلیاژهای پایه نیکل اینکونل 738 و نایمونیک 75 با استفاده از لایه واسط حاوی Ni-Cr-B و با نام تجاری MBF-80 توسط فرآیند فاز مایع گذرا (TLP) در دماهای ℃1080، ℃1120، ℃1150 و ℃1180 و زمان‌های مختلف انجام شد. ریزساختار اتصال با استفاده از میکروسکوپ الکترونی روبشی (SEM) و میکروسکوپ نوری مورد مطالعه قرار گرفت. بررسی‌های ریزساختاری نشان داد که در زمان‌های کوتاه اتصال، ریزساختار شامل فازهای بین فلزی یوتکتیکی پیوسته در خط مرکزی اتصال می‌باشد و با افزایش زمان اتصال در دمای ثابت به‌تدریج از پیوستگی آن کم و نهایتاً به‌طور کامل حذف می‌شوند. به‌منظور پیش‌بینی زمان لازم برای تکمیل انجماد ایزوترم از معادلات نفوذ فیک استفاده شد و مشاهده گردید که تطابق خوبی بین زمان پیش‌بینی شده برای تکمیل انجماد ایزوترم و نتایج تجربی وجود دارد.
Joining of Inconel 738 and Nimonic 75 nickel base superalloys using Ni-Cr-B-containing interlayer, MBF-80, performed by transient liquid phase process (TLP) at 1080, 1120, 1150 and 1180°C and different times. Bonding microstructure was studied using a scanning electron microscope (SEM) and a light microscope. Microstructural studies showed that in short bonding time, the microstructure consists of continuous eutectic intermetallic phases in the center line of the joint and with increasing bonding time at constant temperature, eutectic intermetallic phases gradually decrease from the bonding and finally completely disappear. In order to predict the time required to isotherm solidification completion, Fick’s diffusion equations were used and it was observed that there is a good agreement between the predicted time of isotherm solidification completion and experimental results.
[1] O. A. Ojo, "On liquation cracking of cast inconel 738LC superalloy welds", PhD Dissertation, University of Manitoba, Canada, 2005.
[2] "Nimonic 75 alloy, Special Metals Corporation". 2014.
[3] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure development during transient liquid phase bonding of GTD-111 nickel-based superalloy", Journal of alloys and compounds. vol. 461, pp. 641-647, 2008.
[4] M. Haafkens & J. Matthey, "A new approach to the weldability of nickel-base As-cast and power metallurgy superalloys", Weld. Journal, vol. 61, pp. 25-30, 1982.
[5] M. Abdelfatah & O. Ojo, "On the extension of processing time with increase in temperature during transient-liquid phase bonding", Metallurgical and Materials Transactions A. vol. 40, pp. 377-385, 2009.
[6] J. Mattheij, "Role of brazing in repair of superalloy components–advantages and limitations", Materials science and technology. vol. 1, pp. 608-612, 1985.
[7] M. Mosallaee, A. Ekrami, K. Ohsasa & K. Matsuura, "Microstructural evolution in the transient-liquid-phase bonding area of IN-738LC/BNi-3/IN-738LC", Metallurgical and Materials Transactions A. vol. 39, pp. 2389-2402, 2008.
[8] F. Jalilian, M. Jahazi & R. Drew, "Microstructural evolution during transient liquid phase bonding of Inconel 617 using Ni–Si–B filler metal", Materials Science and Engineering: A. vol. 423, pp. 269-281, 2006.
[9] A. Rabinkin, "Brazing with (NiCoCr)–B–Si amorphous brazing filler metals: alloys, processing, joint structure, properties, applications", Science and Technology of Welding & Joining, vol. 9, pp. 181-199, 2004.
[10] D. Duvall, W. Owczarski & D. Paulonis, "TLP bonding: a new method for joining heat resistant alloys", Pratt and Whitney Aircraft, Middletown, CO. 1974.
[11] T. Shinmura, K. Ohsasa & T. Narita, "Isothermal Solidification Behavior During the Transient Liquid Phase Bonding Process of Nickel Using Binary Filler Metals". vol. 42, pp. 292-297, 2001.
[12] W. MacDonald & T. Eagar, "Transient liquid phase bonding processes", The Metal Science of Joining, pp. 93-100. 1992.
[13] W. Gale and D. Butts, "Transient liquid phase bonding", Science and Technology of Welding & Joining, vol. 9, pp. 283-300, 2004.
[14] M. Pouranvari, A. Ekrami & A. Kokabi, "Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni–Si–B ternary filler alloy", Journal of Alloys and Compounds, vol. 563, pp. 143-149, 2013.
[15] M. Pouranvari, A. Ekrami & A. Kokabi, "Phase transformations during diffusion brazing of IN718/Ni-Cr-B/IN718", Materials Science and Technology, vol. 29, pp. 980-984, 2013.
[16] W. Gale & E. Wallach, "Microstructural development in transient liquid-phase bonding", Metallurgical Transactions A, vol. 22, pp. 2451-2457, 1991.
[17] "Alloy Phase Diagrams", 10 ed. ASM Handbook. Vol. 3, ASM International, 1992.
[18] P. Sung & D. Poirier, "Liquid-solid partition ratios in nickel-base alloys", Metallurgical and Materials Transactions A, vol. 30, pp. 2173-2181, 1999.
[19] A. Bondar, "B-Cr-Ni (Boron-Chromium-Nickel)", Non-Ferrous Metal Ternary Systems. Selected Soldering and Brazing Systems: Phase Diagrams, Crystallographic and Thermodynamic Data.
[20] K. Ohsasa, T. Narita & T. Shinmura, "Numerical modeling of the transient liquid phase bonding process of Ni using Ni-B-Cr ternary filler metal", Journal of phase equilibria, vol. 20, pp. 199-206, 1999.
[21] O. Ojo, N. Richards & M. Chaturvedi, "Isothermal solidification during transient liquid phase bonding of Inconel 738 superalloy", Science and Technology of Welding & Joining, vol. 9, pp. 532-540, 2004.
[22] W. Li, T. Jin, X. Sun, Y. Guo, H. Guan & Z. Hu, "Study of Ni–Cr–Co–W–Mo–B interlayer alloy and its bonding behaviour for a Ni-base single crystal superalloy", Scripta materialia, vol. 48, pp. 1283-1288, 2003.
[23] J. Liu, T. Jin, N. Zhao, Z. Wang, X. F. Sun, H. R. Guan & Z. Q. Hu. Effect of temperature on formation of borides in TLP joint of a kind of nickel-base single crystal superalloy. in Materials science forum, 2007.
[24] O. Ojo, N. Richards & M. Charturvedi, "Effect of gap size and process parameters on diffusion brazing of Inconel 738", Science and Technology of Welding & Joining. vol. 9, pp. 209-220, 2004.
[25] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure–properties relationship of TLP-bonded GTD-111 nickel-base superalloy", Materials Science and Engineering: A. vol. 490, pp. 229-234, 2008.
[26] M. Pouranvari, A. Ekrami & A. Kokabi, "Diffusion induced isothermal solidification during transient liquid phase bonding of cast IN718 superalloy", Canadian Metallurgical Quarterly. vol. 53, pp. 38-46, 2014.
[1] O. A. Ojo, "On liquation cracking of cast inconel 738LC superalloy welds", PhD Dissertation, University of Manitoba, Canada, 2005.
[2] "Nimonic 75 alloy, Special Metals Corporation". 2014.
[3] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure development during transient liquid phase bonding of GTD-111 nickel-based superalloy", Journal of alloys and compounds. vol. 461, pp. 641-647, 2008.
[4] M. Haafkens & J. Matthey, "A new approach to the weldability of nickel-base As-cast and power metallurgy superalloys", Weld. Journal, vol. 61, pp. 25-30, 1982.
[5] M. Abdelfatah & O. Ojo, "On the extension of processing time with increase in temperature during transient-liquid phase bonding", Metallurgical and Materials Transactions A. vol. 40, pp. 377-385, 2009.
[6] J. Mattheij, "Role of brazing in repair of superalloy components–advantages and limitations", Materials science and technology. vol. 1, pp. 608-612, 1985.
[7] M. Mosallaee, A. Ekrami, K. Ohsasa & K. Matsuura, "Microstructural evolution in the transient-liquid-phase bonding area of IN-738LC/BNi-3/IN-738LC", Metallurgical and Materials Transactions A. vol. 39, pp. 2389-2402, 2008.
[8] F. Jalilian, M. Jahazi & R. Drew, "Microstructural evolution during transient liquid phase bonding of Inconel 617 using Ni–Si–B filler metal", Materials Science and Engineering: A. vol. 423, pp. 269-281, 2006.
[9] A. Rabinkin, "Brazing with (NiCoCr)–B–Si amorphous brazing filler metals: alloys, processing, joint structure, properties, applications", Science and Technology of Welding & Joining, vol. 9, pp. 181-199, 2004.
[10] D. Duvall, W. Owczarski & D. Paulonis, "TLP bonding: a new method for joining heat resistant alloys", Pratt and Whitney Aircraft, Middletown, CO. 1974.
[11] T. Shinmura, K. Ohsasa & T. Narita, "Isothermal Solidification Behavior During the Transient Liquid Phase Bonding Process of Nickel Using Binary Filler Metals". vol. 42, pp. 292-297, 2001.
[12] W. MacDonald & T. Eagar, "Transient liquid phase bonding processes", The Metal Science of Joining, pp. 93-100. 1992.
[13] W. Gale and D. Butts, "Transient liquid phase bonding", Science and Technology of Welding & Joining, vol. 9, pp. 283-300, 2004.
[14] M. Pouranvari, A. Ekrami & A. Kokabi, "Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni–Si–B ternary filler alloy", Journal of Alloys and Compounds, vol. 563, pp. 143-149, 2013.
[15] M. Pouranvari, A. Ekrami & A. Kokabi, "Phase transformations during diffusion brazing of IN718/Ni-Cr-B/IN718", Materials Science and Technology, vol. 29, pp. 980-984, 2013.
[16] W. Gale & E. Wallach, "Microstructural development in transient liquid-phase bonding", Metallurgical Transactions A, vol. 22, pp. 2451-2457, 1991.
[17] "Alloy Phase Diagrams", 10 ed. ASM Handbook. Vol. 3, ASM International, 1992.
[18] P. Sung & D. Poirier, "Liquid-solid partition ratios in nickel-base alloys", Metallurgical and Materials Transactions A, vol. 30, pp. 2173-2181, 1999.
[19] A. Bondar, "B-Cr-Ni (Boron-Chromium-Nickel)", Non-Ferrous Metal Ternary Systems. Selected Soldering and Brazing Systems: Phase Diagrams, Crystallographic and Thermodynamic Data.
[20] K. Ohsasa, T. Narita & T. Shinmura, "Numerical modeling of the transient liquid phase bonding process of Ni using Ni-B-Cr ternary filler metal", Journal of phase equilibria, vol. 20, pp. 199-206, 1999.
[21] O. Ojo, N. Richards & M. Chaturvedi, "Isothermal solidification during transient liquid phase bonding of Inconel 738 superalloy", Science and Technology of Welding & Joining, vol. 9, pp. 532-540, 2004.
[22] W. Li, T. Jin, X. Sun, Y. Guo, H. Guan & Z. Hu, "Study of Ni–Cr–Co–W–Mo–B interlayer alloy and its bonding behaviour for a Ni-base single crystal superalloy", Scripta materialia, vol. 48, pp. 1283-1288, 2003.
[23] J. Liu, T. Jin, N. Zhao, Z. Wang, X. F. Sun, H. R. Guan & Z. Q. Hu. Effect of temperature on formation of borides in TLP joint of a kind of nickel-base single crystal superalloy. in Materials science forum, 2007.
[24] O. Ojo, N. Richards & M. Charturvedi, "Effect of gap size and process parameters on diffusion brazing of Inconel 738", Science and Technology of Welding & Joining. vol. 9, pp. 209-220, 2004.
[25] M. Pouranvari, A. Ekrami & A. Kokabi, "Microstructure–properties relationship of TLP-bonded GTD-111 nickel-base superalloy", Materials Science and Engineering: A. vol. 490, pp. 229-234, 2008.
[26] M. Pouranvari, A. Ekrami & A. Kokabi, "Diffusion induced isothermal solidification during transient liquid phase bonding of cast IN718 superalloy", Canadian Metallurgical Quarterly. vol. 53, pp. 38-46, 2014.
[27] M. Arafin, M. Medraj, D. Turner & P. Bocher, "Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: Modeling and experimental investigations", Materials Science and Engineering: A, vol. 447, pp. 125-133, 2007.
[28] I. Tuah-Poku, M. Dollar & T. Massalski, "A study of the transient liquid phase bonding process applied to a Ag/Cu/Ag sandwich joint", Metallurgical Transactions A, vol. 19, pp. 675-686, 1988.
[29] Y. NAKAO, K. Nishimoto, K. Shinozaki & C. Kang, "Theoretical research on transient liquid insert metal diffusion bonding of nickel base alloys", Transactions of the Japan Welding Society, vol. 20, pp. 60-65, 1989.
[30] Y. Zhou, "Analytical modeling of isothermal solidification during transient liquid phase (TLP) bonding", Journal of Materials Science Letters, vol. 20, pp. 841-844, 2001.
[31] M. Pouranvari, "Isothermal solidification during transient liquid-phase bonding of GTD-111/Ni-Si-B/GTD-111", Materiali in tehnologije. vol. 48, pp. 113-118, 2014.
[32] Y. Zhou, W. Gale & T. North, "Modelling of transient liquid phase bonding", International Materials Reviews. vol. 40, pp. 181-196, 1995.
_||_