Analyzing Effect of Friction on Spread and Budge in Flat Rolling by FEM Method

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

محمود سلیمی ¹ , امین فضیله ²

1 - استاد، دانشکده مهندسی مکانیک، دانشگاه صنعتی اصفهان
2 - کارشناس ارشد، دانشکده مهندسی مکانیک، دانشگاه آزاد اسلامی واحد خمینی شهر

Received: 2015-10-03 Accepted : 2015-10-03 Published : 2008-09-22

Keywords: forging, Friction, Rolling, Budge, spread,

Abstract :

In this research a final element model for simulating three dimensional deformation in rolling of flat product is modeling in ABAQUS and further developed to study the frictional effects on spread and bulge. To predict the magnitude of bulging , the rolling process is approximated by successive forging steps. The elongation or the average spread at each step from the previous calculations are used in the model. The theoretical results of the model is in a good agreement with the experimental values given by other investigation.

References:

 [1] Gokyu, I., Kihara, J. and Mae, Y., Lubrication in steel strip rolling, Technology of plasticity Society of Japan ,Vol. 20, December 1987, pp. 316-321.

[2] Kobayashi, S. and Oh, S. I., An Approximate Method for a Three Dimensional Analysis of Rolling, International Journal of Mechanics Science, Vol. 17, 1975, pp. 293-305.

[3] Kennedy, K.F., A Method for Analyzing Spread, Elongation and Bulge in Flat Rolling, Transaction ASME Journal of Engineering Industry, Vol.11,  1987, pp. 305.

[4] Hill, R, A general method of analysis for metal-working processes, Journal of the Mechanics and Physics of Solids, Vol.11, September 1963, pp. 306-326.

[5] Min WANG, He YANG, Zhi-chao SUN, Liang-gang GUO and Xin-zhe OU, Research on the influence of material properties on cold ring rolling processes by 3D-FE numerical simulation,Transactions of Nonferrous Metals Society of China, Vol 16,  December 2006, pp. 1274-1280

[6] Lanyun Li, He Yang, Lianggang Guo and Zhichao Sun, A control method of guide rolls in 3D-FE simulation of ring rolling, Journal of Materials Processing Technology, Vol205, Issues 1-3, 26 August 2008, pp. 99-110.

[7] Kobayashi, S. and Oh,S. I., An Approximate Method for a Three Dimensional Analysis of Rolling, International Journal of Mechanics Science , Vol. 17,  1975, pp. 293-305.

]8[ فضیله، الف، شبیه سازی اثر اصطکاک بر تعریض و برآمدگی جانبی در نورد تخت بوسیله نرم افزار ABAQUS، پایان نامه کارشناسی ارشد، دانشکده مهندسی مکانیک، دانشگاه آزاد خمینی شهر، 1387.

]9[ سلیمی، م، صنیعی، م، بررسی فرایند نورد سرد همراه با روغنکاری تحت رژیم روانکاری مخلوط، پایان نامه کارشناسی ارشد، دانشکده مهندسی مکانیک، دانشگاه صنعتی اصفهان.

]10[ مشکسار، م،کتاب اصول مهندسی نورد،  انتشارات دانشگاه شیراز، 1381.