Evaluation of the Cryogenic Effect on Friction Stir Processed AA7075/Si Matrix Nanocomposites
محورهای موضوعی : Micro/Nano Manufacturing systemsNavid Molla Ramezani 1 , Behnam Davoodi 2
1 - School of Mechanical Engineering, Iran University of Science and Technology, Tehran, Iran
2 - School of Mechanical Engineering, Iran University of Science and Technology, Tehran, Iran
کلید واژه: Friction Stir Processing (FSP), Cryogenic, 7075 Aluminum Alloy, Tool Wear, Surface Quality,
چکیده مقاله :
Friction-stir processing is a green manufacturing process for surface composite fabrication and surface modification. To achieve this critical goal, the type of cooling and lubrication are of great importance. Therefore, in this paper, the cryogenic effects were investigated on friction-stir processing (FSP) tool wear and surface quality of an aluminum matrix nanocomposite. Silicon carbide (SiC) nanopowder was used as the reinforcing phase. The effects of cooling strategy and tool rotation speed on the tool wear, microhardness, surface roughness, and energy dispersive spectroscopy (EDS) analysis were studied. The cooling procedure was conducted under dry and cryogenic conditions. Additionally, the rotation speed was set at three levels, while other parameters were kept constant. The FSP tools were examined under a scanning electron microscope, and the wear mechanisms were investigated under different conditions. The results showed that tool wear, surface roughness, and microhardness were improved under cryogenic conditions compared to air conditions. Furthermore, in the presence of liquid nitrogen, the metal matrix composite did not exhibit any microstructural defects, such as micro-cracks. Energy dispersive spectroscopy analysis also demonstrated that SiC had better penetration into the base material under cryogenic conditions compared to dry conditions.
Friction-stir processing is a green manufacturing process for surface composite fabrication and surface modification. To achieve this critical goal, the type of cooling and lubrication are of great importance. Therefore, in this paper, the cryogenic effects were investigated on friction-stir processing (FSP) tool wear and surface quality of an aluminum matrix nanocomposite. Silicon carbide (SiC) nanopowder was used as the reinforcing phase. The effects of cooling strategy and tool rotation speed on the tool wear, microhardness, surface roughness, and energy dispersive spectroscopy (EDS) analysis were studied. The cooling procedure was conducted under dry and cryogenic conditions. Additionally, the rotation speed was set at three levels, while other parameters were kept constant. The FSP tools were examined under a scanning electron microscope, and the wear mechanisms were investigated under different conditions. The results showed that tool wear, surface roughness, and microhardness were improved under cryogenic conditions compared to air conditions. Furthermore, in the presence of liquid nitrogen, the metal matrix composite did not exhibit any microstructural defects, such as micro-cracks. Energy dispersive spectroscopy analysis also demonstrated that SiC had better penetration into the base material under cryogenic conditions compared to dry conditions.
[1] Padhy, G., C. Wu, and S. Gao. 2018. Friction stir based welding and processing technologies-processes, parameters, microstructures and applications: A review. Journal of Materials Science & Technology. 34(1): 1-38. doi: 10.1016/j.jmst.2017.11.029.
[2] Adiga, K., Herbert, M.A., Rao, S.S. and Shettigar, A. 2022. Applications of reinforcement particles in the fabrication of aluminium metal matrix composites by friction stir processing-A review. Manufacturing Review. 9:26. doi: 10.1051/mfreview/2022025.
[3] Mishra, R.S. and Z. Ma. 2005. Friction stir welding and processing. Materials science and engineering: R: reports. 50(1-2): 1-78. doi: 10.1016/j.mser.2005.07.001.
[4] Mishra, R.S., Z. Ma, and I. Charit. 2003. Friction stir processing: a novel technique for fabrication of surface composite. Materials Science and Engineering: A. 341(1-2): 307-310. doi: 10.1016/S0921-5093(02)00199-5.
[5] Hajideh, M.R., M. Farahani, and N.M. Ramezani. 2018. Reinforced dissimilar friction stir weld of polypropylene to acrylonitrile butadiene styrene with copper nanopowder. Journal of Manufacturing Processes. 32: 445-454. doi: 10.1016/j.jmapro.2018.03.010.
[6] Hajideh, M. R., Farahani, M., Alavi, S. A. D., & Ramezani, N. 2017. Investigation on the effects of tool geometry on the microstructure and the mechanical properties of dissimilar friction stir welded polyethylene and polypropylene sheets. Journal of Manufacturing Processes. 26:269-279. doi: 10.1016/j.jmapro.2017.02.018.
[7] Hajideh, M. R., Shapurgan, O., Ramzani, N. M. and Nejad, E. H. 2017. Friction stir welding of dissimilar poly methyl methacrylate and polycarbonate sheets. Journal of Modern Processes in Manufacturing and Production. 6(4): 35-46. dor: 20.1001.1.27170314.2017.6.4.3.0.
[8] Abushanab, W. S., Moustafa, E. B., Goda, E. S., Ghandourah, E., Taha, M. A.and Mosleh, A. O. 2023. Influence of Vanadium and Niobium Carbide Particles on the Mechanical, Microstructural, and Physical Properties of AA6061 Aluminum-Based Mono-and Hybrid Composite Using FSP. Coatings. 13(1): 142. doi: 10.3390/coatings13010142.
[9] Kumar, T. S., Thankachan, T., Shalini, S., Čep, R. and Kalita, K. 2023. Microstructure, hardness and wear behavior of ZrC particle reinforced AZ31 surface composites synthesized via friction stir processing. Scientific Reports. 13(1): 20089. doi: 10.1038/s41598-023-47381-5.
[10] Diaz, O. G., Luna, G. G., Liao, Z. and Axinte, D. 2019. The new challenges of machining Ceramic Matrix Composites (CMCs): Review of surface integrity. International Journal of Machine Tools and Manufacture. 139: 24-36. doi: 10.1016/j.ijmachtools.2019.01.003.
[11] Keshavarz, H. and A.H. Kokabi. 2023. Influence of pass number on microstructure, mechanical, and tribological properties of cold-rolled Al1050 during friction stir processing. Journal of Materials Research and Technology. 27: p. 932-943. doi: 10.1016/j.jmrt.2023.10.032.
[12] Wu, B., Ibrahim, M. Z., Raja, S., Yusof, F., Muhamad, M. R. B., Huang, R. and Kamangar, S. 2022. The influence of reinforcement particles friction stir processing on microstructure, mechanical properties, tribological and corrosion behaviors: A review. Journal of Materials Research and Technology.20:1940-1975.doi: 10.1016/j.jmrt.2022.07.172.
[13] Khorrami, M. S., Kazeminezhad, M., Miyashita, Y., Saito, N. and Kokabi, A. H. 2017. Influence of ambient and cryogenic temperature on friction stir processing of severely deformed aluminum with SiC nanoparticles. Journal of Alloys and Compounds. 718: 361-372. doi: 10.1016/j.jallcom.2017.05.234.
[14] Fratini, L., Buffa, G. and Shivpuri, R. 2010. Mechanical and metallurgical effects of in process cooling during friction stir welding of AA7075-T6 butt joints. Acta Materialia. 58(6): 2056-2067. doi: 10.1016/j.actamat.2009.11.048.
[15] Fratini, L., Buffa, G. and Shivpuri, R. 2018. Microstructure, mechanical properties and strengthening mechanism of titanium particle reinforced aluminum matrix composites produced by submerged friction stir processing. Materials Science and Engineering: A. 734: 353-363. doi: 10.1016/j.msea.2018.08.015.
[16] Rui-Dong, F., Zeng-Qiang, S., Rui-Cheng, S., Ying, L., Hui-Jie, L.and Lei, L. 2011. Improvement of weld temperature distribution and mechanical properties of 7050 aluminum alloy butt joints by submerged friction stir welding. Materials & Design. 32(10): 4825-4831. doi: 10.1016/j.matdes.2011.06.021.
[17] Sharma, C., Dwivedi, D.K. and Kumar, P. 2012. Influence of in-process cooling on tensile behaviour of friction stir welded joints of AA7039. Materials Science and Engineering: A. 556: 479-487. doi: 10.1016/j.msea.2012.07.016.
[18] Khodabakhshi, F., Gerlich, A. P., Simchi, A. and Kokabi, A. H. 2015. Cryogenic friction-stir processing of ultrafine-grained Al–Mg–TiO2 nanocomposites. Materials Science and Engineering: A. 620: 471-482. doi: 10.1016/j.msea.2014.10.048.
[19] Ramezani, N. M., Rasti, A., Sadeghi, M. H., Pour, B. J.and Hajideh, M. R. 2016. 2016. Experimental study of tool wear and surface roughness on high speed helical milling in D2 steel. Modares Mech Eng. 15(20): 198-202. dor: 20.1001.1.10275940.1394.15.13.72.2.
[20] Molla Ramezani, Ranjbar , H., Sadeghi, M.H. and Rasti, A. 2016. Helical milling of cold-work AISI D2 steel with PVD carbide tool under dry conditions. Modares Mechanical Engineering. 15(13): 203-206. dor: 20.1001.1.10275940.1394.15.13.53.3.
[21] Molla Ramezani, N., Rezaei Hajideh, M.and Shahmirzaloo, A. 2017. Experimental study of the cutting parameters effect on hole making processes in hardened steel. Journal of Modern Processes in Manufacturing and Production. 6(3):67-76. dor: 20.1001.1.27170314.2017.6.3.5.0.
[22] Ashish, B., Saini, J. and Sharma, B. 2016. A review of tool wear prediction during friction stir welding of aluminium matrix composite. Transactions of Nonferrous Metals Society of China. 26(8): 2003-2018. doi: 10.1016/S1003-6326(16)64318-2.
[23] Molla Ramezani, N., Davoodi, B., Aberoumand, M. and Rezaee Hajideh, M. 2019. Assessment of tool wear and mechanical properties of Al 7075 nanocomposite in friction stir processing (FSP). Journal of the Brazilian Society of Mechanical Sciences and Engineering. 41: 1-14. doi: doi.org/10.1007/s40430-019-1683-1.
[24] Molla Ramezani, N., Davoodi, B., Farahani, M. and Khanli, A. H. 2019. Surface integrity of metal matrix nanocomposite produced by friction stir processing (FSP). Journal of the Brazilian Society of Mechanical Sciences and Engineering. 41: 1-11. doi: 10.1007/s40430-019-2014-2.
[25] Fernandez, G. and Murr, L.E. 2004. Characterization of tool wear and weld optimization in the friction-stir welding of cast aluminum 359+ 20% SiC metal-matrix composite. Materials Characterization. 52(1): 65-75. doi: 10.1016/j.jmst.2017.11.029.
[26] Zhang, H., Wang, D., Xue, P., Wu, L. H., Ni, D. R., Xiao, B. L. and Ma, Z. Y. 2018. Achieving ultra-high strength friction stir welded joints of high nitrogen stainless steel by forced water cooling. Journal of materials science & technology. 34(11): 2183-2188. doi: 10.1016/j.jmst.2018.03.014.
[27] Prado, R. A., Murr, L. E., Soto, K. F. and McClure, J. C. 2003. Self-optimization in tool wear for friction-stir welding of Al 6061+ 20% Al2O3 MMC. Materials science and engineering: 349(1-2): 156-165. doi: 10.1016/S0921-5093(02)00750-5.
[28] Nandan, R., Roy, G. G., Lienert, T. J. and Debroy, T. 2007. Three-dimensional heat and material flow during friction stir welding of mild steel. Acta materialia. 55(3): 883-895. doi: 10.1016/j.actamat.2006.09.009.
[29] Khodabakhshi, F. and Gerlich, A. 2018. Potentials and strategies of solid-state additive friction-stir manufacturing technology: A critical review. Journal of Manufacturing Processes. 36: p. 77-92. doi: 10.1016/j.jmapro.2018.09.030.
[30] Nazari, M., Eskandari, H. and Khodabakhshi, F. 2019. Production and characterization of an advanced AA6061-Graphene-TiB2 hybrid surface nanocomposite by multi-pass friction stir processing. Surface and Coatings Technology. 377: 124914. doi: 10.1016/j.surfcoat.2019.124914.
[31] Zuo, L., Shao, W., Zhang, X. and Zuo, D. 2022. Investigation on tool wear in friction stir welding of SiCp/Al composites. Wear. 498: 204331. doi: 10.1016/j.wear.2022.204331.
[32] Gerlich, A.P. 2017. Critical Assessment 25: Friction stir processing, potential and problems. Materials Science and Technology. 33(10):1139-1144. doi: 10.1080/02670836.2017.1300420.
[33] Zhang, H., Liu, H. and Yu, L. 2011. Microstructure and mechanical properties as a function of rotation speed in underwater friction stir welded aluminum alloy joints. Materials & Design. 32(8-9): 4402-4407. doi: 10.1016/j.matdes.2011.03.073.
[34] Upadhyay, P. and Reynolds, A.P. 2010. Effects of thermal boundary conditions in friction stir welded AA7050-T7 sheets. Materials Science and Engineering: A. 527(6): 1537-1543. doi: 10.1016/j.msea.2009.10.039.
[35] Fatchurrohman, N. and Abdullah, A. 2018. Surface Roughness and Wear Properties of Al–Al 2 O 3 Metal Matrix Composites Fabricated Using Friction Stir Processing. Lecture Notes in Intelligent Manufacturing & Mechatronics (Conference paper). doi: 10.1007/978-981-10-8788-2_15.
[36] Kumar, A., Godasu, A. K., Pal, K. and Mula, S. 2018. Effects of in-process cryocooling on metallurgical and mechanical properties of friction stir processed Al7075 alloy. Materials Characterization. 144: 440-447. doi: 10.1016/j.matchar.2018.08.001.
[37] Yildiz, Y. and Nalbant, M. 2008. A review of cryogenic cooling in machining processes. International Journal of Machine Tools and Manufacture. 48(9): 947-964. doi: 10.1016/j.ijmachtools.2008.01.008.
[38] Hotami, M.M. and Yang, S. 2023. Investigation on Micro-Hardness, Surface Roughness and SEM of Nano TiO2/B4C/Graphene Reinforced AA 7075 Composites Fabricated by Frictional Stir Processing. Crystals. 13(3): 522. doi: 10.3390/cryst13030522.
[39] Molla Ramezani, N., Davoodi, B. and Rezaee Hajideh, M. 2018. Investigating the performance of coated carbide insert in hard steel helical milling. ADMT Journal. 11(3): 1-9.
[40] Akbarpour, M. R., Mirabad, H. M., Gazani, F., Khezri, I., Chadegani, A. A., Moeini, A. and Kim, H. S. 2023. An overview of friction stir processing of Cu-SiC composites: microstructural, mechanical, tribological, and electrical properties. 27: 1317-1349. Journal of Materials Research and Technology. doi: 10.1016/j.jmrt.2023.09.200.
[41] Dwivedi, S. P., Sharma, S., Li, C., Zhang, Y., Kumar, A., Singh, R. and Abbas, M. 2023. Effect of nano-TiO2 particles addition on dissimilar AA2024 and AA2014 based composite developed by friction stir process technique. Journal of Materials Research and Technology. 26: 1872-1881. doi: 10.1016/j.jmrt.2023.07.234.
[42] Hirata, T., Oguri, T., Hagino, H., Tanaka, T., Chung, S. W., Takigawa, Y. and Higashi, K. 2007. Influence of friction stir welding parameters on grain size and formability in 5083 aluminum alloy. Materials Science and Engineering: A. 456(1-2): 344-349. doi: 10.1016/j.msea.2006.12.079.
[43] Imani, H., Molla Ramezani, N., Sadeghi, M. H. and Rasti, A. 2016. The effect of hole making method on cutting force and surface roughness. Modares Mechanical Engineering. 15(13): 285-290. dor: 20.1001.1.10275940.1394.15.13.29.9.
[44] Devaraju, A. and Kishan, V. 2018. Influence of cryogenic cooling (liquid nitrogen) on microstructure and mechanical properties of friction stir welded 2014-T6 aluminum alloy. Materials Today: Proceedings, 5(1): 1585-1590. doi: 10.1016/j.matpr.2017.11.250.
