Synthesis of nano-structured sphene and mechanical properties optimization of its scaffold via response surface methodology
محورهای موضوعی : Finite Element ModelingAmirmostafa Amirjani 1 , Masoud Hafezi 2 , Ali Zamanian 3 , Mana Yasaee 4 , Noor Azuan Abu Osman 5
1 - Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran, Iran
2 - Nanotechnology and Advanced Materials Division, Materials and Energy Research Center, Iran
3 - Nanotechnology and Advanced Materials Department, Materials and Energy Research Center, Alborz, Iran.
4 - Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, Tehran, Iran.
5 - Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur, Malaysia.
کلید واژه: Response Surface Methodology, mechanical properties, Bioceramics, Mechano-chemical synthesis,
چکیده مقاله :
Nano-structured sphene (CaTiSiO5) powder was synthesized via mechanical activation and heat treatment method. The synthesized powder was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and simultaneous thermal analysis (STA). The sphene scaffolds were then fabricated via porogen method (using citric acid). Response surface methodology was successfully used to determine the effects of d (particle size) and %V porogen (volume percent of porogen) on the mechanical behavior of the prepared sphene scaffolds. Moreover, a suitable mathematical model for describing the relationship between the factors (d and %V porogen) and the response (compressive strength) was statistically developed. The use of porogen in the synthesis procedure can change the porosity value of the final scaffold; thus, the compressive strength of the sphene scaffolds varied widely. Statistical analysis results predicted that the maximum value of the compressive strength can be obtained at the following conditions: %V = 25% and d = 250 µm. At these conditions, the prepared scaffolds possess a compressive strength value as high as 7 MPa.
[1] J. Pantić, A. Kremenović, A. Došen, M. Prekajski, N. Stanković, Z. Baščarević, B. Matović, "Influence of mechanical activation on sphene based ceramic material synthesis", Ceram. Int., Vol. 39, No. 1, 2013, pp. 483-488.
[2] D. Clarke, "Ceramic materials for the immobilization of nuclear waste", Annu. Rev. Mater. Sci., Vol. 13, No. 1, 1983, pp. 191-218.
[3] Y. Teng, L. Wu, X. Ren, Y. Li, S. Wang, "Synthesis and chemical durability of U-doped sphene ceramics", J. Nucl. Mater., Vol. 444, No. 1, 2014, pp. 270-273.
[4] T. S. Lyubenova, F. Matteucci, A. Costa, M. Dondi, J. Carda, "Ceramic pigments with sphene structure obtained by both spray-and freeze-drying techniques", Powder. Technol., Vol. 193, No. 1, 2009, pp. 1-5.
[5] C. T. Wu, Y. Ramaswamy, D. Gale, W.R. Yang, K.Q. Xiao, L.C. Zhang, Y.B. Yin, H. Zreiqat, "Novel sphene coatings on Ti-6Al-4V for orthopedic implants using sol-gel method", Acta. Biomater. , Vol. 4, No. 3, 2008, pp. 569-576.
[6] C. Wu, Y. Ramaswamy, A. Soeparto, H. Zreiqat, "Incorporation of titanium into calcium silicate improved their chemical stability and biological properties", J. Biomed. Mater. Res. Part A., Vol. 86, No. 2, 2008, pp. 402-410.
[7] Y. Ramaswamy, C. Wu, C. R. Dunstan, B. Hewson, T. Eindorf, G. I. Anderson, H. Zreiqat, "Sphene ceramics for orthopedic coating applications: An in vitro and in vivo study", Acta. Biomater., Vol. 5, No. 8, 2009, pp. 3192-3204.
[8] C. Wu, Y. Ramaswamy, X. Liu, G. Wang, H. Zreiqat, "Plasma-sprayed CaTiSiO5 ceramic coating on Ti-6Al-4V with excellent bonding strength, stability and cellular bioactivity", J. R. Soc. Interface., Vol. 6, No. 31, 2009, pp. 159-168.
[9] M. Fathi, E. M. Zahrani, "Mechanical alloying synthesis and bioactivity evaluation of nanocrystalline fluoridated hydroxyapatite", J. Cryst. Growth., Vol. 311, No. 5, 2009, pp. 1392-1403.
[10] S. H. Park, H. J. Kim, J. I. Cho, Optimal central composite designs for fitting second order response surface linear regression models, in Response Surface Linear Regression Models, Physica-Verlag HD, Heidelberg, 2008, pp. 323-329.
[11] A. Amirjani, M. Bagheri, M. Heydari, S. Hesaraki, "Label-free surface plasmon resonance detection of hydrogen peroxide; a bio-inspired approach", Sens. Actuators. B, Vol. 227, 2016, pp. 373–382.
[12] A. Amirjani, P. Marashi, D. H. Fatmehsari, "Effect of AgNO3 addition rate on aspect ratio of CuCl2–mediated synthesized silver nanowires using response surface methodology", Colloids. Surf., A, Vol. 444, 2014, pp. 33-39.
[13] A. Amirjani, P. Marashi, D. H. Fatmehsari, "Interactive effect of agitation rate and oxidative etching on growth mechanisms of silver nanowires during polyol process ", J. Exp. Nanosci., Vol. 10, 2015, pp. 1387-1400.
[14] E. S. Dana, Manual of Mineralogy, 17th ed., John Wiley &Sons,Inc., 1959, pp. 412–413.
[15] M. J. Mondrinos, R. Dembzynski, L. Lu, V.K. Byrapogu, D.M. Wootton, P.I. Lelkes, J. Zhou, "Porogen-based solid freeform fabrication of polycaprolactone–calcium phosphate scaffolds for tissue engineering", Biomater., Vol. 27, No. 25, 2006, pp. 4399-4408.
[16] I. Zein, D. W. Hutmacher, K. C. Tan, S. H. Teoh, "Fused deposition modeling of novel scaffold architectures for tissue engineering applications", Biomater., Vol. 23, No. 4, 2002, pp. 1169-1185.
[17] J. M. Williams, A. Adewunmi, R. M. Schek, C.L. Flanagan, P. H. Krebsbach, S. E. Feinberg, S. J. Hollister, S. Das, "Bone tissue engineering using polycaprolactone scaffolds fabricated via selective laser sintering", Biomater., Vol. 26, No. 23, 2005, pp. 4817-4827.
