The Prediction of Forming Limit Diagram of Low Carbon Steel Sheets Using Adaptive Fuzzy Inference System Identifier
محورهای موضوعی : Engineering
1 - Department of Mechanical Engineering, Babol University of Technology, Babol, Iran
کلید واژه: Finite Element, Forming Limit Diagram, Out-of-plane, Localized necking, Fuzzy Inference System,
چکیده مقاله :
The paper deals with devising the combination of fuzzy inference systems (FIS) and neural networks called the adaptive network fuzzy inference system (ANFIS) to determine the forming limit diagram (FLD). In this paper, FLDs are determined experimentally for two grades of low carbon steel sheets using out-of-plane (dome) formability test. The effect of different parameters such as work hardening exponent (n), anisotropy (r) and thickness on these diagrams were studied. The out-of-plane stretching test with hemispherical punch was simulated by finite element software Abaqus. The limit strains occurred with localized necking were specified by tracing the thickness strain and its first and second derivatives versus time at the thinnest element. In addition, to investigate the effect of different parameters such as work hardening exponent (n), anisotropy (r) and thickness on these diagrams, a machine learning algorithm is used to simulate a predictive framework. The method of learning algorithm uses the rudiments of neural computing through layering the FIS and using hybrid-learning optimization algorithm. In other words, for building the training database of ANFIS, the experimental work and finite element software Abaqus are used to obtain limit strains. Good agreement was achieved between the predicted data and the experimental results.
[1] Keeler S.P., Backofen W.A., 1963, Plastic instability and fracture in sheets stretched over rigid punches, ASM Trans 56: 25-48.
[2] Goodwin G.M., 1968, Application of strain analysis to sheet metal forming problems in the press shop, SAE, 680093.
[3] Hecker S.S., 1975, Simple technique for determining forming limit curves, Sheet Metal Industries 52: 671-676.
[4] Marciniak Z., Kuczynski K., 1967, Limit strains in the processes of stretch forming, International Journal of Mechanical Sciences 9: 609-620.
[5] Raghavan K.S., 1995, A simple technique to generate in-plane forming limit curves and selected applications, Metallurgical and Materials Transactions 26: 2075-2084.
[6] Clift S.E., Hartley P., Sturgess C.E.N., Rowe G.W., 1990, Fracture prediction in plastic deformation processes, International Journal of Mechanical Sciences 32: 1-17.
[7] Takuda H., Mori K., Hatta N., 1999, The application of some criteria for ductile fracture to the prediction of the forming limit of sheet metals, Journal of Materials Processing Technology 95: 116-121.
[8] Takuda H., Mori K., Takakura N., Yamaguchi K., 2000, Finite element analysis of limit strains in biaxial stretching of sheet metals allowing for ductile fracture, International Journal of Mechanical Sciences 42: 785-798.
[9] Ozturk F., Lee D., 2004, Analysis of forming limits using ductile fracture criteria, Journal of Materials Processing Technology 147: 397-404.
[10] Brun B., Chambard A., Lai M., De Luca P., 1999, Actual and virtual testing techniques for a numerical definition of material, Proceeding of Numisheet 99 Besançon, France.
[11] Geiger M., Merklein M., 2003, Determination of forming limit diagrams-A new analysis method for characterization of materials formability, Annals of the CIRP 52: 213-216.
[12] Petek A., Pepelnjak T., Kuzman K., 2005, An improved method for determining a forming limit diagram in the digital environment, Journal of Mechanical Engineering 51: 330-345.
[13] Pepelnjak T., Petek A., Kuzman K., 2005, Analysis of the forming limit diagram in digital environment, Advanced Material Research 6/8: 697-704.
[14] Friedman P.A., Pan J., 2000, Effects of plastic anisotropy and yield criteria on prediction of forming limit curves, International Journal of Mechanical Sciences 42: 29-48.
[15] Huang H.M., Pan J., Tang S.C., 2000, Failure prediction in anisotropic sheet metals under forming operations with consideration of rotating principal stretch directions, International Journal of Plasticity 16: 611-633.
[16] Cao J., Yao H., Karafillis A., Boyce M.C., 2000, Prediction of localized thinning in sheet metal using a general anisotropic yield criterion, International Journal of Plasticity 16: 1105-1129.
[17] Wu P.D., Jain M., Savoie J., Mac Ewen S.R., Tugcu P., Neale K.W., 2003, Evaluation of anisotropic yield function for aluminum sheets, International Journal of Plasticity 19: 121-138.
[18] Jang J.S.R., 1993, ANFIS: Adaptive-Network-Based Fuzzy Inference System, IEEE Transactions on Systems, Man, and Cybernetics 23(3): 665-685.
[19] Lin J.C., Tai C.C., 1999, The application of neural networks in the prediction of sprint-back in an l-shaped bend, International Journal of Advanced Manufacturing Technology 15: 163-170.
[20] Inamdar M., Narasimhan K., Maiti S.K., Singh U.P., 2000, Development of an artificial neural to predict spring back in air vee bending, International Journal of Advanced Manufacturing Technology 16: 376-381.
[21] Kim D.H., Kim D.J., Kim B.M., 1999, The application of neural networks and statistical methods to process design in metal forming processes, International Journal of Advanced Manufacturing Technology 15: 886-894.
[22] Cao J., Kinsey B., Solla S.A., 2000, Consistent and minimal springback using a stepped binder force trajectory and neural network control, Journal of Engineering Materials and Technology 122: 113-118.
[23] Kazan R., Firat M., Tiryaki A.E., 2009, Prediction of spring back in wipe-bending process of sheet metal using neural network, Materials and Design 30: 418-423.
[24] Wu C.Y., Hsu Y.C., 2002, Optimal shape design of an extrusion die using polynomial networks and genetic algorithms, International Journal of Advanced Manufacturing Technology 19: 79-87.
[25] Yang G., Osakada K., Kurozawa T., 1993, Fuzzy inference model for flow stress of carbon steel, The Japan Society for Technology of Plasticity 34(387): 422-427.
[26] Manabe K., Yoshihara S., Yan M., Nishimura H., 1995, Optimization of the variable BHF deep-drawing process by fuzzy model, The Japan Society for Technology of Plasticity 36 (416): 1015-1022.
[27] Ong S.K., Vin L.J.D.E., Nee A.Y.C., Kals H.J.J., 1997, Fuzzy set theory applied to bend sequencing for sheet metal bending, Journal of Materials Processing Technology 69: 29-36.
[28] Baseri H., Bakhshi-Jooybari M., Rahmani B., 2011, Modeling of spring back in V-die bending process by using fuzzy learning back-propagation algorithm, Expert Systems with Applications 38: 8894-8900.
[29] Lu Y.H., Yeh F.H., Li C.L., Wu M.T., 2005, Study of using ANFIS to the prediction in the bore-expanding process, International Journal of Advanced Manufacturing Technology 26: 544-551.
[30] Lu Y.H., Yeh F.H., Li C.L., Wu M.T., Liu C.H., 2003, Study of ductile fracture and preform design of upsetting process using adaptive network fuzzy inference system, Journal of Materials Processing Technology 140: 576-582.
[31] Hill R., 1948, A theory of yielding and plastic flow of anisotropic metals, Proceedings of the Royal Society of London A 193: 281-297.
[32] Narayanasamy R., Narayanan C., 2006, Forming limit diagram for Indian interstitial free steels, Materials and Design 27: 882-899.
[33] Triantafyllidis N., Samanta S.K., 1986, Bending effects on flow localization in metallic sheets, Proceedings of the Royal Society of London 406: 205-226.
[34] JenabaliJahromi S.A., Nazarboland A., Mansouri E., Abbasi S., 2006, Investigation of formability of low carbon steel sheets by forming limit diagrams, Iranian Journal of Science and Technology 30: 377-385.
