Design and simulation of novel RF MEMS cantilever switch with low actuation voltage
محورهای موضوعی : Majlesi Journal of Telecommunication Devices
Bahram A. Ganji
1
(Department of Electrical Engineering, Babol Noshirvani University of Technology, Babol, Iran)
Khadijeh Khodadady
2
(Department of Electrical Engineering, Babol Noshirvani University of Technology, Babol, Iran)
کلید واژه: Babol noshirvani university, en, Master university, Department of electrical and computer engineering, khadijeh khodadady,
چکیده مقاله :
In this paper a novel RF MEMS cantilever type switch with low actuation voltage is presented. The cantilever beam of switch is supported by two L-shaped springs to reduce the spring constant. The switch is simulated using Intellisuite software. The actuation voltage of switch is achieved about 2 volt and the size of the switch is 110×60µ2m, that in compared with other electrostatic cantilever beam switch, it has a small size, low spring constant and as a result low actuation voltage. Its fabrication is simple due to its simple design. The S-parameters of switch have been simulated with HFSS 9.1 that the results show the insertion loss of 0.07 dB, return loss 0f 25 dB and 17 dB isolation for V, Ka frequencies band. The results show proper performance of switch in this frequencies band and it had less insertion loss compare pervious work and with these properties of switch, return loss and isolation did not changed much.
[1] H.U.Rahman and R.Ramer .(2009(.Three-Bar Novel RF MEMS Switches. IEEE.E. H. Miller, “A note on reflector arrays,” IEEE Trans. Antennas Propagat., to be published.
[2] S.C.Saha، U.Hanke،G. U. Jensen and T.Sather. (2009). “Modelingmof Spring Constant and Pull-down Voltage of Non uniform RF MEMS Cantilever.’’ IEEE http://www.halcyon.com/pub/journals/21ps03-vidmar
[3] H. U.Rahman، T. Hesketh and R.Ramer . (2008). “Low Actuation Voltage RF MEMS Switch with Novel Beam Design Magnetism” Interernational Conference on Emerging Technologies IEEE-ICET ،pp18-19،Octobre.
[4] H.U.Rahman and K Y Chan and R Ramer. ( 2010). “Cantilever beam designs for RF MEMS switches.’’ J. Micromech. Microeng. 20 (2010) 075042 (12pp). IOP
[5] J.Kim، S.Kwon،H.Jeong، S.Lee،I.Song and B.Ju. (2009). “A stiff and flat membrane operated DC contact type RF MEMS switch with low actuation voltage.’’ Sensor and Actuators A، 153،pp 114-119.
[6] H.C.Lee، J.Y.Park ، and J.U.Bu. (2005). “Piezoelectrically Actuated RF MEMS DS Contact Switches with low Voltage Operation.’’ Mi، Ficrowave and Wireless Components Letters ،vol.15،No.4،Aprel. IEEE, 2005.
[7] Gh.Moloudian and M.A.Pirbonyeh. (2014). “Simulation of Cantilever RF MEMS switch,” International Research Jounal of Basic Sciences، vol.8(4)،PP 442-446.
[8] Sarkar Suparana and Dr. A. Vimala juliet. “Design of low voltage RF MEMS capacitive switch with low spring constant’’. ISSN، Vol. 3،Issue 4.2320-3765, 2014.
[9] Bagher Fathi Mohammad، Veladati Hadi، Golmohammadi saed. “A new electrostatically actuated low voltage RF MEMS switch.’’ European Scientific Journal November 2013 edition vol.9، No.33 ISSN: 1857 – 7881 (Print) e - ISSN 1857- 7431, 2013.
[10] M.Rebeiz. “RF MEMS Theory Design and Technology’’, 2003.
[11] B.A Ganji, “design and fabrication of small size and high sensitivity MEMS capacitive microphone”, Ph.D. dissertation. Dept Univ. UKM, 2007.
[12] B. A. Ganji and B. Y. MAjlis, “Design and fabrication of a new MEMS capacitive microphone using a perforated aluminum diaphragm’’. Sensors and Actuators A 149. pp. 29–37. 2009.
[13] B. A. Ganji and B. Y. MAjlis,(2009). “design and fabrication of a novel single-chip MEMS capacitive microphone using slotted diaphragm’’. Micro/NANOlith MEMS MOEMS. pp.021112 (1-7).
[14] B. A. Ganji and B. Y. MAjlis,(2008) “Analytical Analysis of Flat and Corrugated Membranes for MEMS Capacitive Sensors’’ International journal of Nonlinear Dynamics in Engineering and Sciences. 1:1, pp. 47-57.
[15] B. A. Ganji and B. Y. MAjlis,(2009) “Fabrication and Characterization of a New MEMS Capacitive Microphone using Perforated Diaphrag’’ International journal of Nonlinear Dynamics in Engineering and Sciences. 1:1, pp. 47-57.
