Improving High Cycle Fatigue Life in An Exhaust Manifold Using Perimeter Fins with Considering Stress Gradient
محورهای موضوعی :
optimization and simulation
Hojjat Ashouri
1
1 - Department of Mechanical Engineering, Varamin-Pishva Branch, Islamic Azad University, Tehran, Iran
تاریخ دریافت : 1401/10/19
تاریخ پذیرش : 1402/01/27
تاریخ انتشار : 1402/06/10
کلید واژه:
high cycle fatigue life,
perimeter fins,
stress gradient,
exhaust manifold,
چکیده مقاله :
The effect of perimeter fins on the thermal stress and High Cycle Fatigue (HCF) life in an exhaust manifold with considering stress gradient was investigated. For this purpose, coupled thermo-mechanical analysis of an exhaust manifold was carried out. Then HCF life of the component was predicted using a standard stress-life analysis and results were compared to the original exhaust manifold. Mechanical properties of exhaust manifold material were obtained by tensile tests at different temperature. The results of the thermo-mechanical analysis proved that the maximum temperature and stress are visible in the confluence region. The obtained Finite Element Analysis (FEA) proved the fact that perimeter fins reduce the temperature distribution in the exhaust manifolds about 31°C. As a result, the exhaust manifolds tolerate lower temperature and fatigue life will increase. The results of FEA indicated that the stress in the modified exhaust manifolds decreased approximately 19MPa for the sake of depletion of temperature gradient, which can lead to higher fatigue lifetime. The results of HCF showed that the number of cycles of failure for modified exhaust manifold is approximately 63% higher than the results obtained from the original exhaust manifolds. The results of the FEA analysis are compared with the real sample of the cracked exhaust manifold to properly evaluate the results, and it has been shown that critical identified areas correspond to the failure areas of the real sample.
منابع و مأخذ:
Zhang, W., Li, J., Yang, L., Barber, G., Chen, J., Iqbal, O., and Singh, , Multiple 3D-DIC Systems for Measuring the Displacements and Strains of an Engine Exhaust Manifold, SAE Technical Paper No. 2020-01-0540, 2020.
Banuelos, E., Carlos Navarro, L. H., Sawkar, A. N., and Gaikwad, S., Thermal Map of an Exhaust Manifold for a Transient Dyno Test Schedule: Development and Test Data Correlation, SAE Technical Paper No. 2018-01-0126, 2018.
Kuribara, H., Horikawa, H., Teraguchi, T., Nagata, T., and Kitamura, D., Prediction of Fatigue Strength of Motorcycle Exhaust System Considering Vibrating and Thermal Stresses, SAE Technical Paper 2015-32-0739, 2015.
Castro Güiza, G. M., Hormaza, W., Andres, R., Galvis, E., and Méndez Moreno, L .M., Bending Overload and Thermal Fatigue Fractures in a Cast Exhaust Manifold, Journal of Engineering Failure Analysis, doi: 10.1016/j.engfailanal.2017.08.016, 2017.
Liu, Y., Hsin Chen, Y., Sawkar, N., Xu, N., Gaikwad, S., Seaton, P., and Singh,, A Thermo-Mechanical Fatigue Analysis on a Ductile Cast Iron Exhaust Manifold, SAE Technical Paper No.2018-01-1215, 2018.
Luo, X., Zou, P., Zeng, X., Yuan, X., and Li, B., Failure Prediction and Design Optimization of Exhaust Manifold Based on CFD and FEM Analysis, SAE Technical Paper No.2020-01-1166, 2020.
Stephens, R., Fatemi, A., H. Fuchs. Metal Fatigue in Engineering, 2nd Edition, John Wiley, 2001.
Naderi Hagh, N., Mohammadi, A., and Payganeh, G., Thermo-Mechanical High Cycle Fatigue Analysis of Exhaust Manifold of Turbocharged Engine with Two Way Coupling FSI, The Journal of Engine Research, Vol. 60, 2020, pp. 29-45.
Holman, J. P., Heat Tranfer, Mc-Graw Hill press, 2010.
Chen, M., Wang, Y., Wu, W., Cui, Q., Wang, M. K., and Wang,, Thermal-Mechanical Fatigue Prediction of Aluminum Cylinder Head with Integrated Exhaust Manifold of a Turbo Charged Gasoline Engine, SAE Technical Paper No.2016-01-1085, 2016.
Ashouri, H., Effect of Perimeter Fins in Low Cycle Fatigue Life for Exhaust Manifold, Journal of Engine Research, The Journal of Engine Research, Vol. 61, 2021, pp. 23-34.
Öberg, C., Rablbauer, R., Zhu, B., and Jonsson, S., Monotonic and Cyclic Creep of Cast Materials for Exhaust Manifolds, SAE International Journal of Material and Manufacture, Vol. 12, No. 2, 2019, pp. 149-162.
Ashouri, H., Evalluation of Thermal Barrier Coating in Low Cycle Fatigue for Exhaust Manifold, Journal of Simulation & Analysis of Novel Technologies in Mechanical Engineering, Vol. 11, No. 2, 2019, pp. 59-66.
Quan, G., Wu, X., Lafleur, L., and Zhang,, Thermo-Mechanical Fatigue Testing of Welded Tubes for Exhaust Applications, SAE Technical Paper No. 2018-01-0090, 2018.
Ashouri, H., Evaluation of Temperature Effect on Modal Analysis for Exhaust Manifold, Journal of Engine Reserch, Vol. 61, 2021, pp. 11-21.
Salehnejad, M. A., Mohammadi, A., Rezaei, M., and Ahangari,, Cracking Failure Analysis of an Engine Exhaust Manifold at High Temperatures Based on Critical Fracture Toughness and FE Simulation Approach, Journal of Engineering FractureMechanics,DOI.org/10.1016/j.engfracmech.2019.02.005, pp. 1-54, 2019.
Ashouri, H., Thermo-Mechanical Fatigue Simulation of Exhaust Manifolds, Journal of Simulation & Analysis of Novel Technologies in Mechanical Engineering, Vol. 11, No. 2, 2018, pp. 59-66.
Carpenter, M., Jha, P., Ray, S., and Nienhuis, D., Fatigue Tests of Un-Notched and Notched Specimens and Life Prediction Using a Variable Critical Distance Method, SAE Technical Paper No. 2019-01-0801, 2019.
Heywood, J. B., Internal combustion engine fundamentals, McGraw-Hill press, 1998.
Chaboche, J. L., A Review of Some Plasticity and Viscoplasticity Constitutive Theories, International Journal of Plasticity, Vol. 24, 2008, pp. 1642–1693.
McKelvey, S. A., Lee, Y. L., and Barkey, M. E., Stress-Based Uniaxial Fatigue Analysis Using Methods Described in FKM-Guideline, Journal of Failure Analysis and Prevention, 12, 2012, pp. 445-484.
Fang, J. R., Jiang, Q. C., Guanq. F., and Wang, S. Q., The Characteristics of Fatigue Under Isothermal and Thermo-Mechanical Load in Cr-Ni-Mo Cast Hot Work Die Steel, Journal of Fatigue Fracture Engineering Material and Structure, Vol. 25, 2002, pp. 481-488.
Zhongjian, P., Qinghua, H., High Cycle Fatigue Analysis for Oil Pan of Piston Aviation Kerosene Engine, Journal of Engineering Failure Analysis, 49, 2015, pp. 104-112.
Carpenter, M., Jha, P., Ray, S., and Nienhuis, D., Fatigue Tests of Un-Notched and Notched Specimens and Life Prediction Using a Variable Critical Distance Method, SAE Technical Paper No. 2019-01-0801, 2019.
Londhe, A., Yadav,, Thermo-Structural Strength Analysis for Failure Prediction and Concern Resolution of an Exhaust Manifold, CAE, R&D, Mahindra and Mahindra Ltd, Automotive Sector, Nasik, India, 2007.