Experimental Study and Modeling of Friction Stir Welding Process of Aluminum 1100 Alloys, using Artificial Neural Network with Taguchi Method
محورهای موضوعی : Mechanical Engineering
V. Zakeri Mehrabad
1
(Teacher at Azad University of Tabriz, Mechanical Department)
Ali Doniavi
2
(Mechanical Engineering Department, Faculty of Engineering,
Urmia University, Urmia, Iran)
A. Gholipoor
3
(Teacher at Azad University of Tabriz, Mechanical Department
*Corresponding author)
کلید واژه: Tool rotational speed, Microstructure, Workpiece temperature predicting, Taguchi Method, Friction stirs welding, Artificial Neural Network,
چکیده مقاله :
In this paper, the temperature distribution in workpiece and microstructure of welded zone in friction stir welding of aluminum 1100 alloys and the effect of the tool rotational speed on these parameters have investigated experimentally. Also feed forward back propagation neural network has been used to predict the temperature of the workpiece during the welding process by considering the process time and tool rotational speed as input parameters of the neural network. For this purpose, the Taguchi design of experiments has been used and the network with minimum mean squared error was selected. This way of neural network selection is very formal and effective than the existing methods. The selected network mean squared error with this approach is 0.000388, its most differences with experimental inputs is 0.770997ºC and its regression R values is 0.99113. Also according to experimental results, increasing tool rotational speed leads to higher plastic deformation in materials and also causes increasing the friction between tool and workpiece which leads to higher workpiece temperature.
[1] Mishra, R. S., Ma, Z. Y., and Charit, I., “Friction stir welding and processing”, Materials Science and Engineering R, Vol. 50, No.1, 2005, pp. 1–78.
[2] Mishra, R. S., Ma, Z. Y., and Charit, I., “Friction stir processing: a novel technique for fabrication of surface composite”, Materials Science and Engineering A, Vol. 341, No.1, 2003, pp. 307-310.
[3] Hofmann, D. C., Vecchio, K. S., “Submerged friction stir processing (SFSP): An improved method for creating ultra-fine-grained bulk materials”, Materials Science & Engineering A, Vol. 402, No.1, 2005, pp. 234–241.
[4] Darras, B. M., Khraisheh, M. K., Abu-Farha, F. K., and Omar, M. A., “Friction stir processing of commercial AZ31 magnesium alloy”, Journal of Materials Processing Technology, Vol. 191, No.1, 2007, pp. 77–81.
[5] Elangovan, K., Balasubramanian, V., “Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy”, Int J Adv Manuf Technol, Vol. 38, No. 1, 2008, pp. 285–295.
[6] Khodir, S. A., Shibayanagi, T., “Friction stir welding of dissimilar AA2024 and AA7075 aluminum alloys”, Materials Science and Engineering B, Vol. 148, No.1, 2008, pp. 82–87.
[7] Zhang, H., Lin, S. B., Wu, L., Feng, J. C., and Ma, Sh. L., “Defects formation procedure and mathematic model for defect free friction stir welding of magnesium alloy”, Materials and Design, Vol. 27, No.1, 2006, pp. 805–809.
[8] Kostka, A., Coelho, R. S., dos Santos, J., and Pyzalla, A. R., “Microstructure of friction stir welding of aluminium alloy to magnesium alloy”, Scripta Materialia, Vol. 60, No.1, 2009, pp. 953–956.
[9] Elangovan, K., Balasubramanian, V., “Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy”, Materials and Design, Vol. 29, No.1, 2008, pp. 362–373.
[10] Rhodes, C. G., Mahoney, M. W., Bingel, W. H., Spurling, R. A., and Bampton, C. C., “ Effects of friction stir welding on microstructure of 7075 aluminum”, Vol. 36, No.1, 1997, pp. 69-75.
[11] Liu, G., Murr, L. E., Niou, C. S., McClure, J. C., and Vega, F. R., “Microstructural aspects of the friction-stir welding of 6061-T6 aluminum”, Scripta Mater, Vol. 37, No.3, 1997, pp. 355-361.
[12] Murr, L. E., Liu, G., and McClure, J. C., “A TEM study of precipitation and related microstructures in friction-stir-welded 6061 aluminium”, J. Mater. Sci., Vol. 33, No.5, 1998, pp. 1243-1251.
[13] Benavides, S., Li, Y., Murr, L. E., Brown, D., and McClure, J. C., “Low-temperature friction-stir welding of 2024 aluminum”, Scripta Mater, Vol. 41, No.8, 1999, pp. 809-815.
[14] Ko, D., Kim, D. H., Kim, B. M., “Application of artificial neural network and Taguchi method to perform design in metal forming considering workability,” International Journal of Machine Tools & Manufacture Vol. 39, No. 1, 1999, pp. 771–785.
[15] Khaw, J. F. C., Lim, B. S., Lim, L. E. N., “Optimal design of neural networks using the Taguchi method”, Neurocomputing, Vol. 7, No. 1, 1995, pp. 225-245.
[16] Basheer, I. A., Hajmeer, M., “Artificial neural networks: fundamentals, computing, design, and application”, Journal of Microbiological Methods, Vol. 43, No. 1, 2000, pp. 3–31.
[17] Kohonen, T., Self-organisation and Associative Memory, Springer Verlag, Berlin, 1988.
[18] Svozil, D., Kvasnicka,V., Pospichal, J., “Introduction to multi-layer feed-forward neural networks”, Chemometrics and Intelligent Laboratory Systems Vol. 39, No. 1, 1997, pp. 43-62.
[19] Scarselli, F., Tsoi, A. C., “Universal Approximation Using Feedforward Neural Networks: A Survey of Some Existing Methods, and Some New Results”, Neural Networks, Vol. 11, No. 1, 1998, pp. 15–37.
[20] Montgomery, D. C., “Design and Analysis of Experiments”, Fifth Edition, John Wiley & Sons, United States of America, 2001.
[21] Roy, R. K., “A Primer on the Taguchi Method”, Society of Manufacturing Engineers, 2010.
