The Effects of Joint Clearance on the Dynamics of the 3-RPR Planar Parallel Manipulator
محورهای موضوعی : Mechanical EngineeringSeyyed Mojtaba Varedi-Koulaei 1 , Mahdi Bamdad 2
1 - shahrood university of technology
2 - shahrood university of technology
کلید واژه: Dynamic effect, Joint clearance, 3RPR Planar parallel manipulator,
چکیده مقاله :
In reality, clearances in the joints are inevitable due to the defects arising from manufacturing process, design tolerances, and wearing after a certain working period. It leads to a chaotic behaviour including the impact loads which results in an unpredictable response in the system. Since clearance introduces an additional uncontrollable degree of freedom to the manipulator, it causes error and could not be neglected in the manipulator design or analysis. In this study, the dynamic behavior of a planar mechanism with revolute joints, in the presence of clearances is investigated. The planar 3-RPR parallel manipulator with six revolute clearance joints is modelled in MSC.ADAMS software and the simulation results are presented. Moreover, the effects of clearance size on the dynamic characteristics of a planar mechanical system are analysed and compared. What is found out is the prediction of the dynamic error due to the joints clearance for this parallel robot.
[1] Korayem, M. H., Bamdad, M., Zehtab, R. M., and Iranpour, M., “First Experimental Results of Load Carrying Capacity for a Planar Cable-suspended Manipulatorˮ, International Journal of Advanced Design and Manufacturing Technology, Vol. 3, No. 4, 2010, pp. 11-16.
[2] Alibakhshi, R., Mohammadi Daniali, H. R., “Trajectory Optimization of Spherical Parallel Robots using Artificial Neural Networkˮ, International Journal of Advanced Design and Manufacturing Technology, Vol. 7, No. 1, 2014, pp. 91-98.
[3] Korayem, M. H., Bamdad, M., “Dynamic Load-Carrying Capacity of Cable-Suspended Parallel Manipulatorsˮ, International Journal of Advanced Design and Manufacturing Technology, Vol. 44, No. 7, 2009, pp. 829-840.
[4] Korayem, M. H., Bamdad, M., and Akbareh, A., “Trajectory Optimization of Cable Parallel Manipulators in Point-to-Point Motionˮ, Journal of Industrial Engineering, 2010, Vol. 5, pp. 29-34.
[5] Meng, J., Zhang, D., and Li, Z., “Accuracy Analysis of Parallel Manipulators with Joint Clearanceˮ, Journal of Mechanical Design, Vol. 131, No. 1, 2009, pp. 11-13.
[6] Dasgupta, B., Mruthyunjaya, T., “The Stewart Platform Manipulator: A Reviewˮ, Mechanism and Machine Theory, Vol. 35, No. 1, 2000, pp. 15-40.
[7] Farajtabar, M., Daniali, H. M., and Varedi, S. M., “Error Compensation for Continuous Path Operation of 3-RRR Planar Parallel Manipulator with Clearance in the Jointsˮ, Journal of Science and Engineering, Vol. 07, No. 01, 2016, pp. 020-033.
[8] Rahmanian, S., Ghazavi, M. R., “Bifurcation in Planar Slider–Crank Mechanism with Revolute Clearance Jointˮ, Mechanism and Machine Theory, Vol. 91, 2015, pp. 86–101.
[9] Tsai, M. J., Lai, T. H., “Accuracy Analysis of a Multiloop Linkage with Joint Clearancesˮ, Mechanism and Machine Theory, Vol. 43, No, 9, 2008, pp. 1141–1157.
[10] Erkaya, S., Uzmay, I., “A Neural–Genetic (NN–GA) Approach for Optimizing Mechanisms Having Joints with Clearanceˮ, Multibody Syst. Dyn, Vol. 20, No. 1, 2008, pp. 69–83.
[11] Ebrahimi, S., Salahshoor, E., and Maasoomi, M., “Application of the Method of Multiple Scales for Nonlinear Vibration Analysis of Mechanical Systems with Dry and Lubricated Clearance Jointsˮ, Journal of Theoretical and Applied Vibration and Acoustics, Vol. 3, No. 1, 2017, pp. 42-61.
[12] Varedi, S. M., Daniali, H. M., and Dardel, M., “Dynamic Synthesis of a Planar Slider–Crank Mechanism with Clearancesˮ, Nonlinear Dynamics, Vol. 79, 2015, pp. 1587–1600.
[13] Earles, S. W. E., Wu, C. L. S., “Motion Analysis of a Rigid Link Mechanism with Clearance at a Bearing Using Lagrangian Mechanics and Digital Computationˮ, J. Mech., 1973, pp. 83–89.
[14] Lankarani, H. M., Nikravesh, P. E., “A Contact Force Model with Hysteresis Damping for Impact Analysis of Multibody Systemsˮ, Journal Mechanical. Design., Vol. 112, 1990, pp. 369–376.
[15] Flores, P., Ambrosio, J., “Revolute Joints with Clearance in Multibody Systemsˮ, Journal of Computers. and Structures., Vol. 82, 2004, pp. 1359–1369.
[16] Flores, P., Ambrosio, J., Claro, J. C. P., Lankarani, H. M., and Koshy, C. S., “A Study on Dynamics of Mechanical Systems Including Jointswith Clearance and Lubricationˮ, Mechanism and Machine Theory, Vol. 41, 2006, pp. 247–261.
[17] Schwab, A. L., Meijaard, J. P., and Meijers, P., “A Comparison of Revolute Joint Clearance Models in the Dynamic Analysis of Rigid and Elastic Mechanical Systemsˮ, Mechanism and Machine Theory, Vol. 37, 2002, pp. 895–913.
[18] Varedi, S. M., Daniali, H. M., Dardel, M., and Fathi, A., “Optimal Dynamic Design of a Planar Slider–Crank Mechanism with a Joint Clearanceˮ, Mechanism and Machine Theory, Vol. 86, 2015, pp. 191–200.
[19] Varedi, S. M., Daniali, H. M., Dardel, M., and Fathi, A., “A Novel Algorithm for Kinematic and Dynamic Optimal Synthesis of Planar Four-Bar Mechanisms with Joint Clearanceˮ, J. Mech. Sci. Technol., Vol. 29, No. 5, 2015, pp. 2059–2065.
[20] Flores, P., Ambrosio, J., Claro, J. C. P., and Lankarani, H. M., “Spatial Revolute Joints with Clearance for Dynamic Analysis of Multibody Systemsˮ, The Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics., Vol. 220, No. 4, 2006, pp. 257–271.
[21] Tian, Q., Sun, Y., Liu, C., Hu, H., and Flores, P., “Elastohydro dynamic Lubricated Cylindrical Joints for Rigid–Flexible Multibody Dynamicsˮ, Journal of Computers. and Structures., Vol. 114–115, 2013, pp. 106–120.
[22] Jawale, H. P., Thorat, H. T., “Investigation of Positional Error in Two Degree of Freedom Mechanism with Joint Clearance”, ASME Journal of Mechanisms and Robotics., Vol. 4, No. 1, 011002, 2012, pp. 7.
[23] Altuzarra, O., Aginaga, J., Hernández, A., and Zabalza, I., “Workspace Analysis of Positioning Discontinuities Due to Clearances in Parallel Manipulatorsˮ, Mechanism and Machine Theory,Vol. 46, No. 5, 2011, pp. 577–592.
[24] Li Xin, X., Yong Gang, L., “Investigation of Joint Clearance Effects on the Dynamic Performance of a Planar 2-DOF Pick-and-Place Parallel Manipulatorˮ, Robotics and Computer-Integrated Manufacturing., Vol. 30, No. 1, 2014, pp. 62–73.
[25] Farajtabar, M., Daniali, H. M., Varedi, and S. M., “Pick and Place Trajectory Planning of Planar 3-RRR Parallel Manipulator in the Presence of Joint Clearanceˮ, Robotica, Vol. 35, Issue. 2, 2017, pp. 241-253, DOI: 10.1017/S0263574714002768
[26] Varedi Koulaei, S. M., Daniali, H. M., and Farajtabar, M., “The Effects of Joint Clearance on the Dynamics of the 3RRR Planar Parallel Manipulatorˮ, Robotica, Vol. 35, Issue. 6, 2017, pp. 1223-1242, DOI: 10.1017/S0263574715001095.
[27] Varedi Koulaei, S. M., Daniali, H. M., Farajtabar, M., Fathi B., and ShafieeAshtiani, M., “Reducing the Undesirable Effects of Joints Clearance on the Behavior of the Planar 3-RRR Parallel Manipulatorsˮ, Nonlinear Dynamics, Vol. 86, 2016, pp. 1007–1022.
[28] Firoozabadi, A. E., Ebrahimi, S., and Amirian, G., “Dynamic Characteristics of a 3-RPR Planar Parallel Manipulator with Flexible Intermediate Linksˮ, Robotica, Vol. 33, 2015, pp. 1909-1925 DOI:10.1017/S0263574714001118.
[29] Tian, Q., Zhang, Y., Chen, L., and Flores, P., “Dynamics of Spatial Flexible Multibody Systems with Clearance and Lubricated Spherical Jointsˮ, Computers and Structures, Vol. 87, 2009, pp. 913–929.
[30] Tang, A., Li, Y., Qu. H., and Xiao, J., “Dynamics Modeling and Simulating Analysis of a Wire Driven Parallel Mechanismˮ, Procedia Engineering, Vol. 15, 2011, pp. 788-794.
[31] Ardestani, M. A., Asgari, M., “Modeling and Analysis of a Novel 3-DoF Spatial Parallel Robotˮ, 19th International Conference of Mechatronics and Machine Vision in Practice (M2VIP), Auckland, New Zealand, 2012.
[32] Khemili, I., Romdhane, L., “Dynamic Analysis of a Flexible Slider–Crank Mechanism with Clearanceˮ, European Journal of Mechanics A/Solids, Vol. 27, 2008, pp. 882–898.
