Investigation and Optimization of EDM Milling and its Comparison with Die Sink EDM
محورهای موضوعی : Mechanical EngineeringMahmoud Moradi 1 , Reza AbbasiRad 2 , Majid Ghoreishi 3 , Hadi Abdollahi 4 , Majid Rostami 5
1 - Department of Mechanical Engineering,
Malayer University, Malayer, Iran
2 - Department of Mechanical Engineering,
K.N. Toosi University of Technology, Tehran, Iran
3 - Department of Mechanical Engineering,
K.N. Toosi University of Technology, Tehran, Iran
4 - Department of Mechanical Engineering,
Urmia university of Technology, Urmia, Iran
5 - Department of Mechanical Engineering,
Sharif University of Technology, Tehran, Iran
کلید واژه: response surface methodology, Electro discharge milling, Optimization, Die sink EDM,
چکیده مقاله :
In this study EDM milling process parameters of AISI H13, have been investigated by using Response Surface Methodology (RSM). Current (16-32A), pulse-on time (100-700 µs) and depth of cut (1-3mm) were considered as independent variables, while surface roughness, tool wear ratio (TWR), and material removal rate (MRR) as process output responses. Results reveal that increases in the current and decreases in pulse-on time cause more MRR and more TWR and depth of cutting has no significant effect on them. Minimum surface roughness, minimum TWR and maximum MRR were considered as optimization criteria. Verification experiments were carried out in order to analyze the results via software. Optimized settings were used for EDM Milling and die sink EDM experiments to compare the results. The results indicate that using EDM milling has considerable economic savings than die sink EDM, better surface roughness, and higher MRR.
[1] Ding, S., Jiang, R., “Tool Path Generation for 4-axis Contour EDM Rough Machining”, Int J Mach Tool Manu, Vol. 44, No. 14, 2004, pp.1493-1502.
[2] Bleys, P., Kruth, J. P., and Lauwers, B., “Sensing and Compensation of Tool Wear in Milling EDM”, J. Mater. Process. Technol, Vol. 149, No. 1-3, 2004, pp.139–146.
[3] Liu, Y. H., Li, X. P., Ji, R. J., Yu, L. L., and Zhang, H. F., “Effect of Technological Parameter on the Process Performance Electric Discharge Milling of Insulating Al2O3 Ceramic”, J. Mater. Process. Technol, Vol. 208, No. 1-3, 2008, pp. 245-250.
[4] Bayramoglu, M., Duffill, A. W., “CNC EDM of Linear and Circular Contours using Plate Tools”, J. Mater. Process. Technol, Vol. 148, No. 2, 2004, pp. 196–203
[5] Han, F., Wang, Y., and Zhou, M., “High-Speed EDM Milling with Moving Electric Arcs”, INT J Mach Tool Manu, Vol. 49, No. 1, 2009, pp. 20-24
[6] Shamsborhan, M., Moradi, M., and Shokuhfar A., “Numerical Optimization of Planar Twist Channel Angular Extrusion as a novel severe plastic deformation method by DOE method”, Modarres Mechanical Engineering, Vol. 16, No. 5, 2016, pp. 135-144, (in Persian).
[7] Moradi, M., Salimi, N., Ghoreishi, M., Abdollahi, H., Shamsborhan, M., Frostevarg, J., Ilar, T., and Kaplan, A. F. H., “Parameter Dependencies in Laser Hybrid Arc Welding by Design of Experiments and by a Mass Balance”, J. Laser Appl, Vol. 26, No.2, 2014, pp. 1-9.
[8] Vahdati, M., Mahdavinejad, R., Amini, S., and Moradi, M., “Statistical Analysis and Optimization of Factors Affecting the Surface Roughness in UVaSPIF Process using Response Surface Methodology”, Journal of Advanced Materials and Processing, Vol. 3, No. 1, 2015, pp. 15-28.
[9] Azadi, M., Azadi, S., Zahedi, F., and Moradi, M., “Multidisciplinary Optimization of a Car Component under NVH and Weight Constraints using RSM”, ASME 2009 International Mechanical Engineering Congress and Exposition, Lake Buena Vista, Florida, USA, 13–19 November 2009, Vol. 15, pp. 315-319.
[10] Abdollahi, H., Mahdavinejad, R., Ghambari, M., and Moradi, M., “Investigation of Green Properties of Iron/jet-milled Grey Cast iron Compacts by Response Surface Method”, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 228, No. 4, 2014, pp. 493-503.
[11] Assarzadeh, S., Ghoreishi, M., “Statistical Investigation into the Effects of Electro-Discharge Machining Parameters on WC/6%Co Composite-Part 2: Parametric Analysis and Optimization through Desirability Function (DF)”, International Journal of Advanced Materials Manufacturing & Characterization, Vol. 3, No. 2, 2013, pp. 463-468.
[12] Karthikeyan, G., Garg, A. K., Ramkumar, J., and Dhamodaran, S., “A Microscopic Investigation of Machining Behaviour in ED-Milling Process”, J. of Manuf. Process, Vol. 14, No.3, 2012, pp. 297–306.
[13] Jafferson, J. M., Hariharan, P., Kumar, J. R, “Effect of Non-electrical Parameters in μ ED Milling: an Experimental Investigation”, Int J. Adv. Manuf. Technol., Vol. 95, 2016, pp. 15-22
[14] Yang Shen et al., “High-throughput Electrical Discharge Milling of WC–8%Co”, Int J. Adv. Manuf. Technol., Vol. 82, No. 5, 2012, pp. 1071–1078
[15] Montgomery, D. C., “Design and Analysis of Experiments”, Wiley, New York, 2005.
[16] Myers, R. H., Montgomery, D. C., “Anderson-Cook, Response Surface Methodology (RSM): Process and Product Optimization using Designed Experiments”, 3rd ed., Wiley, New York, 2009.
[17] Khuri, A. I., Cornell, J. A., “Response Surfaces Design and Analysisˮ, 2nd ed., Marcel Dekker, New York, 1996.
[18] “Minitab software”, release 17, http://www.minitab.com.
[19] Chen, Y., Mahdavian, S. M., “Parametric Study into Wear in a Computer Numerical Controlled Electro-Discharge Machining Process Wear”, Vol. 236, No. 1-2, 1999, pp. 350-354.
