Optimization of AZ61 Mg Alloy Resistance Spot Welding using Response Surface Method
محورهای موضوعی : weldingAfshin Lotfi 1 , Davood Afshari 2 , Zuheir Barsoum 3
1 - Faculty of Engineering,
University of Zanjan, Iran
2 - Faculty of Engineering,
University of Zanjan, Iran
3 - Faculty of Vehicle Engineering,
Royal Institute of Technology, Sweden
کلید واژه: AZ61 Mg Alloy, Response Surface Method, Resistance Spot Weld, Optimization,
چکیده مقاله :
The purpose of this study is to investigate the effect of resistance spot welding (RSW) parameters on nugget size and ultimate strength of Magnesium alloy sheets AZ61 under tensile-shear test. In this study microstructural examination and hardness measurements were carried out on the welded samples. The results show that the weld nugget zone is divided into two separate parts: the equiaxed dendritic zone (EDZ) perched at the center of the weld nugget and the columnar dendritic zone (CDZ) situated around the fine-grained zone having it surrounded. The effect of the following three parameters: electric current, welding time and electrode force on the dimensions of the weld nugget and the welded ultimate strength is investigated. The response surface method (RSM) is employed to examine the effects of welding parameters and to attain optimum parameters. The analysis of variance (ANOVA) results of RSM model shows that however the tensile-shear strength and nugget size are improved with increasing the welding current and welding time, the welding current is the most influential parameter. In addition, the optimal values for the welding parameters are calculated to achieve the maximum nugget size and the ultimate strength of welded joint. Finally, a regression model is proposed in order to predict the peak load and the nugget size as function of the mentioned welding parameters.
[1] Cole, G. S., Magnesium Vision 2020: A North American Automotive Strategic Vision for Magnesium, Wiley, New York, USA, 2014, pp. 35-40.
[2] Li, Y., Wei, Z., Li, Y., Shen, Q., and Lin, Z., Effects of Cone Angle of Truncated Electrode on Heat and Mass Transfer in Resistance Spot Welding, International Journal of Heat and Mass Transfer, Vol. 65, 2013, pp. 400–408.
[3] Kramar, T., Vondro, P., Kolarikova, M., and Ondruska, M., Resistance Spot Welding of Magnesium Alloy AZ61, Science Journal, Vol. 01, 2015, pp. 596–599.
[4] Behravesh, S. B., Jahed, H., and Lambert, S., Characterization of Magnesium Spot Welds Under Tensile and Cyclic loadings, Materials and Design, Vol. 32, No.10, 2011, pp. 4890–4900.
[5] Hao, C., Zhang, J., Gan, Z., Chen, H., Zhang, H., and Luo, H., Characteristics of Resistance Welding Magnesium Alloys AZ31 and AZ91, Welding Journal, Vol. 90, No. 12, 2011, pp. 249–257.
[6] Afshari, D., Sedighi, M., Barsoum, Z., and Peng, R. L., An Approach in Prediction of the Failure Load in Resistance Spot Welded Aluminum 6061-T6 Under Quasi-Static Tensile Test, IMechE Part B: Journal of Engineering Manufacture, Vol. 226, No. 6, 2012, pp. 1026-1032.
[7] Niknejad, S., Liu, L., Lee, M., Esmaeili, S., and Zhou, N., Resistance Spot Welding of AZ Series Magnesium Alloys: Effects of Aluminum Content on Microstructure and Mechanical Properties, Materials Science and Engineering: A, Vol. 618, 2014, pp. 323-334.
[8] Babu, N. K., Brauser, S., Rethmeier, M., and Cross, C. E., Characterization of Microstructure and Deformation Behavior of Resistance Spot Welded AZ31 Magnesium Alloy, Materials Science and Engineering: A, Vol. 549, 2012, pp. 149-156.
[9] Mirzaei, F., Ghorbani, H., and Kolahan, F., Effects of Process Parameters on Tensile-Shear Strength and Failure Mode of Resistance Spot Welds of AISI 201 Stainless Steel, International Journal Advanced Manufacturing Technology, Vol. 92, No. 5-8, 2017, pp. 3489-3501.
[10] Safari, M., Mostaan, H., Yadeghari, H. K., and Asgari, D., Numerical Modeling and Optimization of Joint Strength in Resistance Spot Welding of Galvanized Steel Sheets, International Journal Advanced Manufacturing Technology, Vol. 89, 2017, pp. 1853-1863.
[11] Liu, L., Xiao, L., Feng, J. C., Tian, Y. H., Zhou, S. Q., and Zhou, Y., Resistance Spot Welded AZ31 Magnesium Alloys, part II: Effects of Welding Current on Microstructure and Mechanical Properties, Metallurgical and Materials Transactions A, Vol. 41, No. 10, 2010, pp. 2642-2650.
[12] Xiao, L., Liu, L., Zhou, Y., and Esmaeili, S., Resistance-Spot-Welded AZ31 Magnesium Alloys: Part I. Dependence of Fusion Zone Microstructures on Second-Phase Particles, Metallurgical and Materials Transactions A, Vol. 41, No. 6, 2010, pp. 1511-1522.
[13] Xiao, L., Liu, L., Esmaeili, S., and Zhou, Y., Microstructure Refinement After the Addition of Titanium Particles in AZ31 Magnesium Alloy Resistance Spot Welds, Metallurgical and Materials Transactions A, Vol. 43, No. 2, 2012, pp. 598-609.
[14] Chao, Y. J., Failure Mode of Spot Welds: Interfacial Versus Pullout, Science and Technology of Welding and Joining, Vol. 8, No. 2, 2003, pp. 133–137.
[15] Niknejad, S. T., Liu, L., Nguyen, T., Lee, M. Y., Esmaeili, S., and Zhou, N. Y., Effects of Heat Treatment on Grain-Boundary β-Mg17Al12 and Fracture Properties of Resistance Spot-Welded AZ80 Mg Alloy, Metallurgical and Materials Transactions A, Vol. 44, No.8, 2013, pp. 3747–3756.
