A Comprehensive Review of Thermal Barrier Coatings Microstructure with Different Platinum-Modified Aluminide Bond Coats
محورهای موضوعی : Journal of Environmental Friendly Materials
1 - Advanced Materials Engineering Research Center, Karaj Branch, Islamic Azad University, Karaj, Iran
کلید واژه:
چکیده مقاله :
Thermal Barrier Coatings (TBCs) are used to protect the surface of hot components of gas turbines. TBCs usually have three layers and include a Top Coat (TC) ceramic layer, an intermediate metallic Bond Coat (BC) layer, and a Thermally Grown Oxide (TGO) layer. In the present study, a brief survey of the microstructure of the ceramic layer produced by Air Plasma Spray (APS) and Electron Beam Physical Vapor Deposition (EB-PVD) has been done. Due to the inherent microstructure of the top coat ceramic layer, Diffusion aluminide bond coats are widely used in thermal barrier coatings for oxidation and hot corrosion resistance of Ni-base superalloy components of advanced gas turbine engines. Modifying these coatings by Pt addition considerably improves their high-temperature oxidation resistance. This effect of Pt has prompted intense research on the microstructure and oxidation behavior of Pt-modified aluminide coatings (Pt-Al) over the past several decades. The present review is to collate the available information on the subject. The study includes traditional b-(Ni, Pt)Al bond coats as well as the Pt-modified g–g¢ type of bond coats that have gained prominence in more recent times. A brief description of typical process steps involved in the formation of Pt-aluminide coatings is provided followed by a detailed assessment of coating microstructures reported under various processing conditions. The influence of prior diffusion treatment, on the coating microstructure, is highlighted. The various mechanisms of the role of Pt in enhancing the oxidation and resistance of aluminide coatings, as suggested in the literature, are discussed.
[1] R. C. Reed: The Superalloys-Fundamentals and Applications, Cambridge University Press, New York, (2006), 261
[2] P. Lindloff: Space Engineering: Structural Materials Handbook- Part 5: New Advanced Materials, Advanced Metallic Materials, General Design Aspects and Load Transfer and Design of Joints, ESA Requirements & Standards Division, ESTEC, Noordwijk, (2011), 58.
[3] D. Francois, A. Pineau and A. Zaoui: Mechanical Behaviour of Materials-Solid Mechanics and Its Application.Chapter 8: Creep-Fatigue-Oxidation Interaction, Springer, Dordrecht, (2013), 407.
[4] D. J. Leo, M. J. Walsh, D. Mclashlan, and A. M. Kursunsky, Int. J. Fatigue, 31(2009), 1966.
[5] T. K. Kim, J. Yu and J. Y. Jeon, Metall. Mater. Trans. A, 23A(1992), 2581.
[6] R. W. Fawley: The Superalloys, Wiley, New York, (1972), 312.
[7] I. Gurrappa, I. V. S. Yashwanth and I. Mounika: Gas Turbines - Materials, Modeling and Performance, Chapter 3: The Importance of Hot, Corrosion and its Effective Prevention for Enhanced Efficiency of Gas Turbines, INTECH Publication, New York, (2015), 55.
[8] D. Driver, D. W. Hall, and G. W. Meetham: The Gas Turbine Engine, the Development of Gas Turbine Materials, Springer, London, (1981), 175.
[9] U. Schulz, K. Fritscher, C. Leyens, M. Peters and W. A. Kaysser, JOM, 49(1997), 370.
[10] M. Góral, P. Sosnowy, J. Achiev. Mater. Manuf. Eng., 55(2012), 912.
[11] K.A. Marino, E.A. Carter, Acta Mater. , 58(2010), 2726.
[12] M. Góral, M. Pytel, W. Cmela and M. Drajewicz, Solid State Phenom. , 227(2015), 321.
[13] D. R. Clarke, M. Oechsner and N.P. Padture, MRS Bull., 37(2012), 891.
[14] A. Afrasiabi, M. Saremi and A. Kobayashi, Mater. Sci. Eng. A, 478(2008), 264.
[15] X. Chen, Y. Zhao, L. Gu, B. Zou, Y. Wang and X. Cao, Corros. Sci., 53(2011), 2335.
[16] X. Chen, Y. Zhao, X. Fan, Y. Liu, B. Zou, Y. Wang, H. Ma and X. Cao, Surf. Coat. Technol., 205(2011), 3293.
[17] Y. Wang and G. Sayre, Surf. Coat. Technol., 203(2009), 2186.
[18] D. R. Clarke, Surf. Coat. Technol., 163 (2003), 67.
[19] Y. He, K. N. Lee, S. Tewari and R. A Miller, J. Therm. Spray Technol., 9(2000), 59.
[20] D. Zhou, O. Guillon and R. Vaßen, Coatings, 7(2017), 1.
[21] V. Postolenko, Failure mechanisms of thermal barrier coatings for high temperature gas turbine components under cyclic thermal loading, Ph.D Thesis, Kiev University, Kiev, Ukraine (2008).
[22] H. Zhao, Low conductivity thermal barrier coatings, Ph.D Thesis, the School of Engineering and Applied Science, University of Virginia, Virginia, USA (2009).
[23] T. M. Pollock, D. M. Lipkin and K. J. Hemker, MRS Bull., 37(2012), 923.
[24] A. Rabieifar, S. Nategh, M.R. Afshar and H. Najafi, Mater. Res. Express, 7(2020), 1.
[25] Q. Hongyu, Y. Xiaoguang and W. Yamei, Int J Fract. , 157(2009), 71.
[26] J. R. Nicholls, N. J. Simms, W. Chan and H. E. Evans, Surf. Coat. Technol., 149(2002), 236.
[27] Z. G. Liu, J. H. Ouyang, Y. Zhou and X. L. Xia, J. Eur. Ceram. Soc., 29(2009), 2423.
[28] Y. Liu, T. Nakamura, V. Srinivasan, A. Vaidya, A. Gouldstone and S. Sampath, Acta Mater., 55(2007), 4667.
[29] S. Sampath, U. Schulz, M. O. Jarligo and S. Kurod, MRS Bull., 37(2012), 903.
[30] S. Kurod and T.W. Clyne, Thin Solid Films, 200(1991), 49.
[31] D. D. Hass, Thermal Barrier Coatings, Directed Vapor Deposition of Thermal Barrier Coatings, Ph.D Thesis, the School of Engineering and Applied Science, University of Virginia, Virginia, USA (2000).
[32] A. Kawasaki and R. Watanabe, Mater. Sci. Forum, 308-311(1999), 402.
[33] A. Feuerstein, J. Knapp, T. Taylor, A. Ashary, A. Bolcavage and N. Hitchman, J. Therm. Spray Technol., 17(2008), 199.
[34] S. Bose: High Temperature Coatings, Elsevier, Amsterdam, (2007), 145.
[35] U. Leushake, T. Krell, U. Schulz, M. Peters, W. A. Kaysser and B. H. Rabin, Surf. Coat. Technol., 94(1997), 131.
[36]. A. Keyvani, M. Saremi and M.H. Sohi, J. Alloys Compd., 506(2010), 103.
[37] Z. Chen, N. Q. Wu, J. Singh and S. X. Mao, Thin Solid Films, 443(2003), 46.
[38] H. Singh, S. S. Chatha, H. S. Sidhu and K. Sharma, Int. J. Adv. Robot. Syst., 3(2011), 85.
[39] Z. Zhan, Z. Liu, J. Liu, L. Li, Z. Li and P. Liao, Appl. Surf. Sci., 256(2010), 3874.
[40] J. Liu, H. J. Choi and Y. H. Sohn, 47th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition, American Institute of Aeronautics and Astronautics, Florida, (2009), 94.
[41] K. Shirvani, M. Saremi, M. A. Nishikata and T. Tsuru, Mater. Trans., 43(2002), 2622.
[42] J. W. Lee and Y. C. Kuo, Surf. Coat. Technol., 201(2006), 3867.
[43] R. Swadzba, M. Hetmańczyk, J. Wiedermann, L. Swadzba, G. Moskal, B. Witala and K. Radwański, Surf. Coat. Technol., 215(2013), 16.
[44] N. Vialas and D. Monceau, Surf. Coat. Technol., 201(2006), 3846.
[45] R. E. Malush, P. Deaband and D.H. Boone, Surf. Coat. Technol., 36(1988), 13.
[46] B. A. Pint, J. A. Haynes and Y. Zhang, Surf. Coat. Technol., 205(2010), 1236.
[47] K. Shirvani, S. Firouzi and A. Rashidghamat, Corros. Sci., 55(2012), 378.
[48] R. Swadźba, J. Wiedermann, M. Hetmańczyk, L. Swadźba, B. Mendala, B. Witala and Ł. Komendera, Surf. Coat. Technol., 237(2013), 16.
[49] Y. Q. Wang and G. Sayre, Surf. Coat. Technol., 203(2008), 256.
[50] G. P. Cammarota, A. Casagrande and G. Sambogna, Surf. Coat. Technol., 201(2006), 230.
[51] C. T. Liu, J. Ma, X. F. Sun and P. C. Zhao, Surf. Coat. Technol., 204(2010), 3641.
[52] R. Streiff and D. H. Boone, J. Mater. Eng., 10(1988), 15.
[53] W. Goward and D. H. Boone, Oxid. Met., 3(1971), 475.
[54] G. Lehnert and H. Meinhardt, Surf. Coat. Technol., 1(1972), 71.
[55] G. C. Fryburg, F. J. Kohl and C. A. Stearns, J. Electrochem. Soc., 131(1984), 2958.
[56] M. R. Jackson and J. R. Rairden, Metall Trans. A, 8A(1977), 1697.
[57] J. A. Conner, Int. Gas Turbines and Aeroengines Congress and Exposition, ASME, Cologne, (1992), 1.
[58] R. L. Penven, W. Levason and D. Pletcher, J. Appl. Electrochem., 22(1992), 415.
[59] S. J. Hemsley and W. Zhou, Trans. Inst. Met. Finish. , 88(2010), 11.
[60] D. K. Das, Prog. Mater. Sci., 58(2013), 151.
[61] G. W. Goward, Surf. Coat. Technol., 108-109(1998), 73.
[62] D. K. Das, V. Singh and S. V. Joshi, Metall Mater. Trans. A, 31A(2000), 2037.
[63] J. Benoist, K. F. Badawi, A. Malie and C. Ramade, Surf. Coat. Technol., 194(2005), 48.
[64] F. Pedraza, A. Kennedy, J. Kopecek and P. Moretto, Surf. Coat. Technol., 200(2006), 4032.
[65] Y. Q. Wang and G. Sayre, Surf. Coat. Technol., 203(2009), 1264.
[66] D. K. Das, V. Singh and S. V. Joshi, Oxid. Met. , 57(2002), 245.
[67] H. M. Tawancy and M. Al-Hadhrami, J. Eng. Gas Turbine Power, 134(2012), 012101.
[68] J. Angenete and K. Stiller, Surf. Coat. Technol. , 150(2002), 107.
[69] G. R. Krishna, D. K. Das, V. Singh and S. V. Joshi, Mater Sci. Eng A, 251(1998), 40.
[70] D. K. Das and J. Annapurna, Development of Pt-aluminide coatings on CM-247 Ni-base superalloy: A preliminary study on mechanism of coating formation, Defence metallurgical research center, Hyderabad, (1996), 187.
[71] Y. Li, S. Li, C. Zhang, N. Xu and Z. Bao, Crystals, 11(2021), 972.
[72] D. K. Das, B. Gleeson, K. S. Murphy, S. Ma and T. M. Pollok, Mater. Sci. Technol., 25(2009), 300.
[73] P. Audigie, S. Selezneff, A. V. Put, C. Estourne, S. Hamadi and D. Monceau, Oxid. Met. , 81(2014), 33.
[74] T. A. Kircher, B. G. Mc Mordieand and A. McCarter, Surf. Coat. Technol., 68-69(1994), 32.
[75] G. J. Tatlock, T. J. Hurd and J. S. Punni, Platin Met. Rev., 31(1987), 26.
[76] J. G. Fountain, F. A. Golightly, F. H. Scott and G. C. Wood, Oxid Met., 10(1976), 341.
[77] D. J. Young: High Temperature Oxidation and Corrosion of Metal, Elsevier, Amsterdam, (2008), 214.
[78] J. H. W. De Wit and P. A. Van Manen, Mater. Sci. Forum., 154(1994), 109.
[79] G. R. Johnston, J. L. Cocking and W. C. Johnson, Oxid Met., 23(1985), 237.
[80] S. B. Newcomb, W. M. Stobbs, Proc. Conf. on elevated temperature coatings: science and technology II, Metals Mater. Soc. Anaheim, California, (1996), 265.
[81] K. L. Luthra and H. S. Spacil, J. Electrochem. Soc., 129(1982), 649.
[82] I. M. Allam, H. C. Akuezue and D. P. Whittle, Oxid Met., 14(1980), 517.
[83] B. A. Pint, I. G. Wright, W. Y. Lee, Y. Zhang, K. Prubner and K. B. Alexander, Mater. Sci. Eng. A, 245(1998), 201.
[84] H. Svensson, M. Christensen, P. Knutsson, G. Wahnström and K. Stiller, Corros. Sci., 51(2009), 539.
[85] N. Birks, G. H. Meier and F. S. Petit: Introduction to the High Temperature Oxidation of Metals, Cambridge University Press, New York, (2006), 275.
[86] K. M. Carling, E. A. Carter, Acta. Mater., 55(2007), 2791.
[87] A. H. Heuer and D. B. Hovis, J. Am. Ceram. Soc., 94(2011), 146.
[88] B. A. Pint, Oxid Met., 45(1996), 1.
[89] X. Tan, X. Peng and F. Wang, Corros. Sci., 85(2014), 280.
[90] K. A. Marino and E. A. Carter, Acta Mater., 56(2008), 3502.
[91] P. Kiruthika and A. Paul, Philos. Mag. Lett., 95(2015), 138.
[92] B. Hinnemann and E. A. Carter, J. Phys. Chem., 111(2007), 7105.
[93] H. Svensson, J. Angenete and K. Stiller, Surf. Coat. Technol., 177-178(2004), 152.
[94] R. Prescott and M. J. Graham, Oxid Met., 38(1992), 233.
[95] C. Leyens, B. A. Pint and I. G. Wright, Surf. Coat. Technol., 133(2000), 15.
[96] D. Liu, P. E. Flewitt and M. Pavier, Procedia Manuf., 3(2014), 1729.
[97] B. A. Pint, Surf. Coat. Technol., 188-189(2004), 71.
[98] J. A. Haynes, K. L. More, B. A. Pint, I. G. Wright, K. Cooley and Y. Zhang, Mater. Sci. Forum, 369-372(2001), 679.
[99] P. Y. Hou and V. K. Tolpygo, Surf. Coat. Technol., 202(2007), 623.
[100] B. A. Pint and K. L. More, J. Mater. Sci., 44(2009), 1676.
[101] K. A. Unocic, C. M. Parish and B. A. Pint, Surf. Coat. Technol., 206(2011), 1522.
[102] Y. Zhang, W. Y. Lee, J. A. Haynes, I. G. Wright, B. A. Pint, K. M. Cooley and P. K. Liaw, Metall. Mater. Trans. A, 30A(1999), 2679.
[103] Y. Zhang, J.A. Haynes, W.Y. Lee, I.G. Wright, B.A. Pint, K.M. Cooley and P.K. Liaw, Metall. Mater. Trans. A, 32A(2001), 1727.
[104] N. Otsuka and R.A. Rapp, J. Electrochem. Soc., 137(1990), 46.
[105] B. Baufeld and U. Schulz, Surf. Coat. Technol. , 201(2006), 2667.
[106] Y. Tamarin: Protective Coatings for Turbine Blades, ASM Int., Ohio, (2002), 55.
[107] S. Chen, F. Ke, M. Zhou and Y. Bai, Acta Mater., 55(2007), 3169.
[108] S. J. Hong, G. H. Hwang, W. K. Han and S. G. Kang, Surf. Coat. Technol., 203(2009), 3066.
[109] M. Yavorska and J. Sieniawski, Arch. Mater. Sci. Eng., 45(2010), 56.
[110] J. Benoist, K. F. Badawi, A. Malie and C. Ramade, Surf. Coat. Technol., 182(2004), 14.
[111] K. G. S. Thomas and M. Hertter, Surf. Coat. Technol., 120-121(1999), 84.
[112] A. C. Karaoglanli, K. M. Doleker, B. Demirel, A. Turk and R. Varol, Appl. Surf. Sci., 354(2015), 314.
[113] J. H. Lee, P. C. Tsai and J. W. Lee, Thin Solid Films, 517(2009), 5253.
