Optimization the Mechanical Properties of PVC/n-NBR Blends Using Taguchi Experimental Design Method

Subject Areas :

Alireza Afshari ¹ ( Department of Polymer Engineering, Tehran South Branch, Islamic Azad University, Tehran, Iran. )
Mohammadreza Kalaee ² ( Nano Research Center, Tehran South Branch, Islamic Azad University, Tehran, Iran. )
Mehdi Moghri ³ ( Department of Polymer Engineering, Kashan Branch, Islamic Azad University, Kashan, Iran. )

Received: 2021-04-13 Accepted : 2021-08-23 Published : 2022-05-22

Keywords: Mechanical Properties, Morphology, Design of experiment, Toughness, Poly (vinyl chloride), Acrylonitrile Butadiene Rubber,

Abstract :

The aim of this paper is to study the morphology and mechanical properties of poly(vinyl chloride) (PVC) blends containing acrylonitrile butadiene rubber (NBR) nanoparticles prepared in a counter rotating twin- screw extruder. The effect of nanoparticle’s percent, mixing temperature and time and rotor speed on the properties were studied using the experimental design method. Considering toughness increase of the blends as an optimal state, the process conditions and NBR percent were determined. Scanning electron microscopy (SEM) images showed dispersed matrix-droplet morphology. Uniform distribution of NBR rubber particles was observed within the PVC matrix due to the good compatibility between the rubber particles and the matrix. It was also observed that scattered droplets are present in the spherical form as well as elongated particles within the PVC matrix. Obtained results along with experimental design data showed that the optimal state of break strain and toughness is related to the state with a mixing temperature of about 180 °C, mixing time of 6 minutes, mixing speed of about 70 rpm and a nanoparticle percentage of 2%. The analysis of variance showed that the greatest effect on the modulus was related to the percentage of NBR, while the lowest was related to the mixing time. After that, mixing temperature has the highest share. Interactions between different factors and their effects on tensile modulus showed that the highest intensity of the interaction index is related to the interaction of mixing temperature with mixing time and the lowest is the time and percentage of NBR.

References:

[1] M. C. Senake Perera, U. S. Ishiaku & Z. A. Mohd. Ishak, "Characterisation of PVC/NBR and PVC/ENR50 binary blends and PVC/ENR50/NBR ternary blends by DMA and solid state NMR", European Polymer Journal, vol. 37, no. 1, pp.167 -178, 2001.

 

[2] M. C. Senake Perera, U. S. Ishiaku & Z. A Mohd. "Ishak, Polymer Degradation and Stability", vol. 68, no. 3, pp. 393-402, 2000.

 

[3] Ch. T. Ratnam, S. Kamaruddin & Z. Abdullah, "Irradiation Modification of PVC/NBR Blend", Polymer-Plastics Technology and Engineering, vol. 50, no. 8, pp. 833-838, 2011.

 

[4] J. X. Li & C. M. Chan, "Effect of the size of the dispersed NBR phase in PVC/NBR blends on the stability of PVC to electron irradiation", Polymer, vol. 42, no. 16, pp. 6833-6839, 2001.

 

[5] A. Hajibaba, G. Naderi, E. Esmizadeh & M. H. R. Ghoreishy, "Morphology and dynamic-mechanical properties of PVC/NBR blends reinforced with two types of nanoparticles", Journal of Composite Materials, vol. 48, no. 2, pp. 131-141, 2012.

 

[6] Z. H. Liu, et al. "Effect of morphology on the brittle ductile transition of polymer blends: 2. Analysis on poly (vinyl chloride)/nitrile rubber blends", Polymer, vol. 39, no. 2, pp. 5019-5025, 1998.

 

[7] Z. H. Liu, et al. "Effects of interfacial adhesion on the rubber toughening of poly (vinyl chloride) Part 1. Impact tests", Polymer, vol. 42, no. 2, pp. 737–746, 2001.

 

[8] X. P. Zhang, S. Z. Liu, L. Liu & J. Yin, "Partially sulfonated poly(arylene ether sulfone)-b-polybutadiene for proton exchange membrane", Polymer, vol. 46, no 6, pp.1719–1724, 2005.

 

[9] M. Matsuo, C. Nozaki & Y. Jyo. "Fine structures and fracture processes in plastic/rubber two ‐phase polymer systems. II. Observation of crazing behaviors under the electron microscope", Polym. Eng. & Sci. vol. 9, no. 3, pp. 206-212,1969

 

[10] M. Matsuo, A. Ueda & Y. Kondo, "Fine structures and fracture processes in plastic‐rubber two‐phase polymer systems III. Temperature dependence of Charpy impact strength", Polym. Eng. & Sci, vol. 10, no. 5, pp. 253-260, 1968.

 

[11] Q. Wang, X. Zhang & S. Liu, "Ultrafine full-vulcanized powdered rubbers/PVC compounds with higher toughness and higher heat resistance", Polymer, vol. 46, no. 46, pp.10614-10617, 2005

 

[12] M. Barghamadi, M. Karrabi & M. H. R. Ghoreishy, "Somayyeh Mohammadian-Gezaz, Effects of two types of nanoparticles on the cure, rheological, and mechanical properties of rubber nanocomposites based on the NBR/PVC blends", Journal of Applied Polymer Science, vol. 136, no. 25, pp. 47550, 2019.

 

[13] S. Rad, E. Aali, S. Hallajian, D. Zangeneh, M. Tavakoli, K. Ayub & M. Peyravi, "Enhancement in the mechanical property of NBR/PVC nanocomposite by using sulfur and electron beam curing in the presence of Cloisite 30B nanoclay", Journal of Macromolecular Science, Part A, Pure and Applied Chemistry, vol. 57, no. 2, pp. 123-130, 2020.