Studying the effect of Bi2O3 addition before and after calcination on electrical properties of (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 piezoceramics

Subject Areas :

Raziye Hayati ¹ ( Department of Materials Engineering, Faculty of Engineering, Yasouj University, Yasouj, Iran )
Mohammad Ali Bahrevar ² ( Semiconductor division, Materials & Energy Research Center, Karaj )

Received: 2018-01-25 Accepted : 2019-06-18 Published : 2019-06-18

Keywords: Electrical properties, Sinter, Bi2O3, BCZT, Lead-free Piezoelectric,

Abstract :

Lead-free Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT) compounds were synthesized using the conventional solid state ceramic processing and the effects of Bi2O3 addition on density and electrical properties was investigated. In order to decrease the loss of Bi at high processing temperatures of BCZT, two methods were employed to introduce bismuth oxide; one, in which Bi2O3 was mixed with the raw materials and the composition was balanced for A-site substitution before calcination and the other where Bi2O3 (0.1mol%) was added after calcination, milled, compacted, and sintered (1350-1500 °C) with no compensation at A or B-sites. Phase and microstructure analyses were carried out using x-ray diffractometry and scanning electron microscopy. The temperature and frequency dependence of dielectric properties showed a normal ferroelectric behavior. Our results revealed that Bi incorporation based on the second method was more effective in increasing the density and improving the electrical properties. The highest direct and converse piezoelectric constants, planar coupling factor, and remnant polarization obtained were d33=325 pC/m, d33*=675 pm/V (d33*/d33=2.1), kp=0.42, and Pr=10.4 µC/cm2, respectively, for the BCZT sample with 0.1 mol% Bi2O3, as sintering aid, sintered at 1350 °C, which were attributed to the larger grains and higher density of the corresponding composition.

References:

 

[1]     J. Rödel, et al., “Perspective on the development of lead-free piezoceramicsˮ, Journal of the American Ceramic Society, Vol. 92, pp. 1153-1177, 2009.

 

[2]     L. E. Cross & R. E. Newnham, “History of Ferroelectrics, in Ceramics and civilization: High-technology Ceramics-Past, present and future, W.D. Kingery, Editorˮ, The American Ceramic Society Inc.: USA, 1986.

 

[3]     F. Bourguiba, et al., “Effect of iron and tungsten substitution on the dielectric response and phase transformations of BaTiO3 pervoskite ceramicˮ, Journal of Alloys and Compounds, Vol. 686, pp. 675-683, 2016.

 

[4]     J. P. Ma, et al., “Microstructure, dielectric, and energy storage properties of BaTiO3 ceramics prepared via cold sinteringˮ, Ceramics International, Vol. 44, No. 4, pp. 4436-4441, 2018.

 

[5]     X. Wang, H. Lai-Wa Chan & C. L. Choy, “Positive temperature coefficient of resistivity effect in niobium-doped barium titanate ceramics obtained at low sintering temperatureˮ, Journal of the European Ceramic Society, Vol. 24, No. 6, pp. 1227-1231, 2004.

 

[6]     C. Gao, et al., “Nanocrystalline semiconducting donor-doped BaTiO3 ceramics for laminated PTC thermistorˮ, Journal of the European Ceramic Society, Vol. 37. No. 4, pp. 1523-1528, 2017.

 

[7]     Y. Cui, et al., “Lead-free (Ba0.85Ca0.15) (Ti0.9Zr0.1) O3–CeO2 ceramics with high piezoelectric coefficient obtained by low-temperature sinteringˮ, Ceramics International, Vol. 38, No. 6, pp. 4761-4764, 2012.

 

[8]     Y. Cui, et al., “Lead-free (Ba0.85Ca0.15) (Ti0.9Zr0.1) O3-Y2O3 ceramics with large piezoelectric coefficient obtained by low-temperature sinteringˮ, Journal of Materials Science: Materials in Electronics, Vol. 24, No. 2, pp. 654-657, 2013.

 

[9]     Y. Cui, et al., “Lead-free (Ba0.7Ca0.3) TiO3-Ba(Zr0.2Ti0.8) O3-xwt %CuO ceramics with high piezoelectric coefficient by low-temperature sinteringˮ, Journal of Materials Science: Materials in Electronics, Vol. 23, No. 7, pp. 1342-1345, 2012.

 

[10] H. Du, et al., “Microstructure, Piezoelectric, and Ferroelectric Properties of Bi2O3-Added (K0.5Na0.5) NbO3 Lead-Free Ceramicsˮ, Journal of the American Ceramic Society, Vol. 90, No. 9, pp. 2824-2829, 2007.

 

[11] H. Du, et al., “Microstructure, Piezoelectric, and Ferroelectric Properties of Bi2O3-Added (K0.5Na0.5) NbO3 Lead-Free Ceramicsˮ, Journal of the American Ceramic Society, Vol. 90, No. 9, pp. 2824-2829, 2007.

 

[12] F. Bahri, et al., “Classical or Relaxor Ferroelectric Behaviour of Ceramics with Composition Ba1—xBi2x/3TiO3ˮ, physica status solidi A, Vol. 184, No. 2, pp. 459-464, 2001.

 

[13] F. Bahri & H. Khemakhem, “Relaxor behavior and dielectric properties of Ba1−xBi2x/3Zr0.15Ti0.85O3 solid solutionˮ, Journal of Alloys and Compounds, Vol. 593, pp. 202-206, 2014.

 

[14] J. Zhang, et al., “Dielectric and ferroelectric responses of Ba0.99 − xBi2x/3Ca0.01Zr0.02Ti0.98O3 ceramicsˮ, Materials Research Bulletin, Vol. 69, pp. 51-55, 2015.

 

[15] R. Hayati, et al., “Effects of Bi2O3 additive on sintering process and dielectric, ferroelectric, and piezoelectric properties of (Ba0.85Ca0.15) (Zr0.1Ti0.9) O3 lead-free piezoceramicsˮ, Journal of the European Ceramic Society, Vol. 36, No. 14, pp. 3391-3400, 2016.

 

[16] J. Liu, et al., “Dielectric permittivity and electric modulus in Bi2Ti4O11ˮ, The Journal of Chemical Physics, Vol. 119, No. 5, pp. 2812-2819, 2003.

 

[17] N A. Lomanova, et al., “Properties of aurivillius phases in the Bi4Ti3O12-BiFeO3 systemˮ, Inorganic Materials, Vol. 42, No. 2, pp. 189-195, 2006.

 

[18] R. Hayati, “Optimizing the composition of lead free (Ba1-xCax) (ZryTi1-y) O3 piezoceramics in order to facilitate the sintering process and promote the electrical propertiesˮ, PhD Dissertation, Materials & Research Center, Iran, 2016.

 

[19] N. A. Lomanova, V. L. Ugolkov & V. V. Gusarov, “Thermal behavior of layered perovskite-like compounds in the Bi4Ti3O12-BiFeO3 systemˮ, Lass Physics and Chemistry, Vol. 33, No. 6, pp. 608-612, 2007.