Numerical simulation of thermal plasma spray

Subject Areas :

علی رضا گنجوئی ¹

1 - عضو هیات علمی

Received: 2016-01-20 Accepted : 2016-04-03 Published : 2017-02-19

Keywords:

References:

[1]     J. Ramshaw & C. Chang, “Computational fluid dynamics modeling of multicomponent thermal plasmas”, Plasma chemistry and plasma processing, Vol. 12, No. 3, pp. 299-325, 1992.

 

[2]     S. V. Patankar, “Numerical heat transfer and fluid flow”, Taylor & Francis, 1980.

 

[3]     http://www.wikipg.com/wiki.

 

[4]     http://coating.blogfa.com/post-25.aspx.

 

[5]     I. Ahmed & T. Bergman, “Simulation of thermal plasma spraying of partially molten ceramics: effect of carrier gas on particle deposition and phase change phenomena”, Journal of heat transfer, Vol. 123, No. 1, pp. 188-196, 2001.

 

[6]     Y. Wan, V. Prasad, G. X. Wang, S. Sampath & J. Fincke, “Model and powder particle heating, melting, resolidification, and evaporation in plasma spraying processes”, Journal of heat transfer, Vol. 121, No. 3, pp. 691-699, 1999.

 

[7]     C. Ang, A. Devasenapathi, H. Ng, S. Yu, & Y. Lam, “A proposed process control chart for DC plasma spraying process. Part II. Experimental verification for spraying alumina”, Plasma Chemistry and Plasma Processing, Vol. 21, No. 3, pp. 401-420, 2001.

 

[8]     L. Pawlowski, “The Science and Engineering of Thermal Spray Coatings”, Guidford, Surrey: Wiley, Vol. 414, 1995.

 

[9]     H. B. XiongL. L. Zheng, S. Sampath,R. L. Williamson, & J. R. Fincke, “Three-dimensional simulation of plasma spray: effects of carrier gas flow and particle injection on plasma jet and entrained particle behavior”, International journal of heat and mass transfer, Vol. 47, No. 24, pp. 5189-5200, 2004.

 

[10] H. P. Li & X. Chen, “Three-dimensional modeling  of the turbulent plasma jet impinging upon a flat plate and with transverse particle and carrier-gas injection”, Plasma chemistry and plasma processing, Vol. 22, No. 1, pp. 27-58, 2002.

 

[11] K. Remesh, S. Yu, H. Ng & C. Berndt, “Computational study and experimental comparison of the in-flight particle behavior for an external injection plasma spray process”, Journal of thermal spray technology, Vol. 12, No. 4, pp. 508-522, 2003.

 

[12] B. M. Cetegen & W. Yu: Thermal Spray Technol, 1999.

 

[13] G. Mariaux, E. Legros & A. Vardelle, “Modeling of coating formation and heat flux to substrate by particles and plasma jet in plasma spraying”, Proceedings of the ITSC 2003: International Thermal Spray Conference 2003: Advancing the Science and Applying the Technology, pp. 895-903, 2003.

 

[14] M. Vardelle, P. Fauchais, A. Vardelle & K. I. Li, B. Dussoubs & N. Themelis, “Controlling particle injection in plasma spraying”, Journal of Thermal Spray Technology, Vol. 10, No. 2, pp. 267-284, 2001.

 

[15] B. Selvan, K. Ramachandran, K. P. Sreekumar & T. K. Thiyagarajan, P. V. Ananthapadmanabhan: Numerical and experimental studies on DC plasma spray torch, 2010.

 

[16] M. Leylavergne, B. Dussoubs, A. Vardelle & N. Goubot, J. Thermal Spray Technol. 7 Ž4. Ž1998. 527.

 

[17] E.  Pfender, Thin Solid Films 238 Ž1994. 228.

 

[18] B. Kear & P. Strutt, “Chemical processing and applications for nanostructured materials”, Nanostructured materials, Vol. 6, No. 1, pp. 227-236, 1995.

 

[19] M. Gell, “The potential for nanostructured materials in gas turbine engines”, Nanostructured Materials, Vol. 6, No. 5, pp. 997-1000, 1995.

 

[20] I. Ahmed, T. Bergman, “Three-dimensional simulation of thermal plasma spraying of partially molten ceramic agglomerates”, Journal of thermal spray technology, Vol. 9, No. 2, pp. 215-224, 2000.

 

[21] S. Salhi & N. Guessasma, Fenineche: Yttria-Stabilized Zirconia In-Flight Particle characteristics under vacuum plasma Spray Conditions, 2009.

 

[22] R. L. Williamson, J. R. Fincke & C. H. Chang: “A Computational Examination of the Sources of Statistical Variances in Particle Parameters During Thermal Plasma Spraying,” Plasma Chem. Plasma Process, Vol. 20, No. 3, pp. 299-324, 2000.

 

[23] S. Morsi & A. Alexander, “An investigation of particle trajectories in two-phase flow systems”, J. Fluid Mech, Vol. 55, No. 2, pp. 193-208, 1972.

 

[24] W. Ranz & W. Marshall, “Evaporation from drops”, Chem. Eng. Prog, Vol. 48, No. 3, pp. 141-146, 1952.

 

[25] R. Williamson, J. Fincke, D. Crawford, S. Snyder, W. Swank & D. Haggard, “Entrainment in high-velocity”, high-temperature plasma jets.: Part II: computational results and comparison to experiment, International journal of heat and mass transfer, Vol. 46, No. 22, pp. 4215-4228, 2003.

 

[26] L. S. Fan & C. Zhu, “Principles of Gas –Solid Flows, Cambridge Series in Chemical Engineering”, ed: Cambridge University Press, United Kingdom, 1998.