Current Issue Issue 2 Vol 15 Summer 2024 Submit Your Paper Published Issues Vol. 15 ✓ Issue 2 - Summer 2024 ✓ Issue 1 - Spring 2024 Vol. 14 ✓ Issue 4 - Winter 2024 ✓ Issue 3 - Autumn 2024 ✓ Issue 2 - Summer 2024 ✓ Issue 1 - Spring 2023 Vol. 13 ✓ Issue 4 - Winter 2022 ✓ Issue 3 - Autumn 2022 ✓ Issue 2 - Summer 2023 ✓ Issue 1 - Spring 2022 Vol. 12 ✓ Issue 4 - Winter 2022 ✓ Issue 3 - Autumn 2022 ✓ Issue 2 - Summer 2021 ✓ Issue 1 - Spring 2021 Vol. 11 ✓ Issue 4 - Winter 2021 ✓ Issue 3 - Autumn 2021 ✓ Issue 2 - Summer 2020 ✓ Issue 1 - Spring 2020 Vol. 10 ✓ Issue 4 - Winter 2020 ✓ Issue 3 - Autumn 2019 ✓ Issue 2 - Summer 2019 ✓ Issue 1 - Spring 2019 Vol. 9 ✓ Issue 2 - Winter 2019 ✓ Issue 1 - Autumn 2018 Vol. 8 ✓ Issue 4 - Summer 2018 ✓ Issue 3 - Spring 2018 ✓ Issue 2 - Winter 2018 ✓ Issue 1 - Autumn 2018 Vol. 7 ✓ Issue 4 - Summer 2017 ✓ Issue 3 - Spring 2017 ✓ Issue 2 - Winter 2017 ✓ Issue 1 - Autumn 2016 Vol. 6 ✓ Issue 4 - Spring 2016 ✓ Issue 3 - Summer 2016 ✓ Issue 2 - Winter 2016 ✓ Issue 1 - Autumn 2016 Vol. 5 ✓ Issue 4 - Summer 2026 ✓ Issue 3 - Spring 2026 ✓ Issue 2 - Winter 2026 ✓ Issue 1 - Autumn 2014 Vol. 4 ✓ Issue 6 - Summer 2014 ✓ Issue 5 - Spring 2014 ✓ Issue 4 - Winter 2013 ✓ Issue 3 - Autumn 2013 ✓ Issue 2 - Summer 2026 ✓ Issue 1 - Spring 2026 Vol. 3 ✓ Issue 4 - Winter 2026 ✓ Issue 3 - Autumn 2026 ✓ Issue 2 - Summer 2012 ✓ Issue 1 - Spring 2012 Vol. 2 ✓ Issue 4 - Winter 2012 ✓ Issue 3 - Autumn 2011 ✓ Issue 2 - Summer 2011 ✓ Issue 1 - Spring 2011 Vol. 1 ✓ Issue 2 - Winter 2011 ✓ Issue 1 - Autumn 2010 Menu • About Journal • Aims and Scope • Authors Guide • Evaluation Process • Publication Ethics Contact Journal Browse • Current Issue • By Issue • Author Index • By Subject • By Author
List of Articles Mehdi Ojaghi Open Access Article Abstract Page Full-Text 1 - Introduction: Titanium alloys containing the β phase have much better corrosion resistance. Some alloying elements, such as Mo, stabilize this phase. Among the Ti alloys that contain this element, the Ti-10Mo alloy is of particular importance. If this alloy is produced using selective laser melting (SLM), it will be an approach that is user-friendly due to the nature of the process. Methods: Samples were printed by SLM process. The constituent phases were determined by XRD. The microstructure was evaluated using optical and scanning electron microscopes. Corrosion behavior was evaluated by cyclic potentiodynamic polarization and electrochemical impedance spectroscopy. Findings: In the XRD pattern of pure Ti powder and printed sample, α and α/α' phases are seen, respectively. However, Ti-10Mo powder mixture consists of α and Mo phases, the β phase is more dominant in printed sample because of the Mo penetration in the Ti matrix. As well as, in the microstructure of Ti10Mo the beta phase is seen as Mo-rich streaks, whereas in pure Ti it is found relatively negligible as epitaxially grown primary columnar β grains with acicular α' martensite phase. Mo addition to pure Ti reduces its passive current density and stabilize oxide film. However, Ti-10Mo alloy, with its various phases and galvanic couples, experiences rupture of the passive oxide film at higher potentials, leading to pitting corrosion. The impedance module value of Ti-10Mo is higher than that of pure Ti. Both samples have a double passive oxide film, with Ti-10Mo alloy exhibiting higher resistance than pure Ti. Arezoo Pourshoja karim Avak Maziyar Azadbeh Mohamadreza Etminanfar Mehdi Ojaghi 10.30495/jnm.2024.33378.2040
