Stress and Strain Analysis in Cup Drawing Process for Different Materials using ANSYS Software

Subject Areas : metal forming

siva prasad  kondapalli ¹ (Department of Mechanical Engineering, Anil Neerukonda Institute of Technology & Sciences, India)
GURRAM  RAVITEJA ² (Department of Mechanical Engineering, Anil Neerukonda Institute of Technology & Sciences, India)

Received: 2021-06-25 Accepted : 2021-10-05 Published : 2021-12-01

Keywords: Cup Drawing, ANSYS, CATIA,

Abstract :

Sheet metal forming is widely used in automotive and aerospace industry. In this paper analysis of sheet metal forming process by deep drawing was discussed. Static analysis on the deep drawing operation was carried out to find the stresses, strains and total deformation of deep drawing cup. CAD models are generated using CATIA from the dimensions obtained by theoretical calculations and analysis is carried out using ANSYS software. The force required to develop the cup, deformation and defect like tearing, wrinkles etc. can be obtained through simulation. By using this method it is easy to make stress and strain analysis for different materials. From the analysis it is observed that Titanium has the maximum stress with standing ability when compared to copper and Aluminum.

References:

• Colgan, M., Monaghan, J., Deep Drawing process: analysis and experiment, Journal of Materials Processing Technology, Vol. 132, 2003, pp. 35 -41.


• Raju, S., Ganesan, G., and Karthikeyan, R., Influence of Variables in Deep Drawing of AA 6061 Sheet, Trans. Non-Ferrous Society of China, Vol. 20, 2010, pp. 1856-1862.


• Gowtham, K., Srikanth, K. V. N. S., and Murty, k. L. N., Simulation of the Effect of Die Radius On Deep Drawing Process, International Journal of Applied Research in Mechanical Engineering, Vol. 2, No. 1, 2012, pp. 12-17.


• Padmanabhan, R., Oliveira, M. C., Alves, J. L., and Menezes, L. F., Inuence of Process Parameters On the Deep Drawing of Stainless Steel, Finite Elements in Analysis and Design, Vol. 43, 2007, pp. 1062 -1067.


• Venkat Reddy, R., Janardhan Reddy, T. A., and Reddy, G. C. M., Effect of Various Parameters on the Wrinkling in Deep Drawing Cylindrical Cups, International Journal of Engineering Trends and Technology, Vol. 3, No. 1, 2012, pp. 53-58.


• Marumo, Y., Saiki, H., and Ruan, L., Effect of Sheet thickness on Deep Drawing of Metal Foils, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 20, No. 1-2, 2007, pp. 479-482.


• Arezodar, F., and Eghbali, A., Evaluating the Parameters Affecting the Distribution of Thickness in Cup Deep drawing of ST14 Sheet, Journal of Advanced Science and Engineering Research, Vol. 2, No. 3, 2012, pp. 223-231.


• Joshi, R., Kothari, K. D., and Jhala, R. L., Effects of Different Parameters On Deep Drawing Process, International Journal of Engineering Research & Technology, Vol. 2, No. 3, 2013, pp. 1-5.


• Young, H. M., Yong, K. K., Jin, W. P., and Sung, R. G., Deep Drawing with Internal Air-Pressing to Increase the Limit Drawing Ratio of Aluminum Sheet, KSME International Journal, Vol. 15, No. 4, 2001, pp. 459- 464.


• Saniee, F. F., and Montazeran, M. H., A Comparative Estimation of the Forming Load In the Deep Drawing Process, Journals of Materials Processing’s Technology, Vol. 140, 2003, pp. 555-561.


• Verma, R., and Chandra, S., An Improved Model for Predicting Limiting Drawing Ratio, Journals of Materials Processing Technology, 2005, pp. 1-07.


• Li, Y. Q., Cui, Z. S., Ruan, X. Y., and Zhang, D. J., CAE-Based Six Sigma Robust Optimization for Deep-Drawing Sheet Metal Process, International Journal of Advanced Manufacturing Technology, Vol. 30, 2006, pp. 631–637.


• Ravindra Reddy, P. V. R., Chandra Mohan Reddy, G., and Janardhan Reddy, T. A., Studies on the Effect of Blank Holding Force and The Die Corner Radius On the Limit Strains in The Deep Drawing Process, Indian Journal of Engineering and Material Science, Vol. 19, 2012, pp. 24-30.


• Mehta, N. C., Shiyani, V. V., and Nasit, J. R., Metal Forming Analysis, International Journal of Emerging Technology and Advanced Engineering, Vol. 3, 2013, pp. 190-196.