Evaluation of tribological properties of (Ti,Al)CN/DLC composite coatings deposited by cathodic arc method.

Subject Areas : Surface Engineering

Laleh Zahiri ¹ (Dep. of Mater. Eng., Fac. of Eng., Shahrekord Uni., Shahrekord, Iran)
Moahammad saeri ² (Department Of Materials Eng., Faculty Of Eng., Shahrekord Uni., Shahrekord, Iran. Email: [e-mail])
Shahram Alirezaee ³ (Naghsh-E- Jahan University, Baharestan, Isfahan, Iran. Email:)
Alireza Afkhami ⁴ (M.Sc. in Materials Engineering, Researcher, Marine Industry,-Department of Subsurface Vessels, Shahin Shahr, Isfahan, Iran.)

Received: 2016-04-02 Accepted : 2016-07-10 Published : 2016-06-01

Keywords:

References:

[1]    T. Fu, Z.F. Zhou, Y.M. Zhou, X.D. Zhu, Q.F. Zeng, C.P. Wang, K.Y. Li and J. Lu, “Mechanical properties of DLC coating sputter deposited on surface nanocrystallized 304 stainless steel”, J Surf. Coat. Tech., Vol.207, 2012, pp. 555-564.

[2]    A.M. Ladwig, R.D. Koch, E.G. Wenski and R.F. Hicks, “Atmospheric plasma deposition of diamond-like carbon coatings”, J. Diamond Related Mater., Vol. 18, 2009, pp.1129-1133.

[3]    C. Donnetand and A. Erdemir, “Tribology of DlC film Fundamentals and applications”, 2008, Springer, pp. 243-316.

[4]    M. Moseler, P. Gumbsch, C. Casiraghi, A.C. Ferrari, J. Robertson, “The Ultrasmoothness of Diamond-like Carbon Surfaces” Surf. Sci., Vol. 309, 2005, pp. 1545-1548.

[5]    J. Choi, K. Soejima, T. Kato, M. Kawaguchi and W. Lee. “Nitriding of high speed steel by bipolar PBII for improvement in adhesion strength of DLC films” Nuclear Instrum. Methods. Phy. Res. Sec. B, Vol.272, 2012, pp. 357-360.

[6]    S. Zhang, Y. Fu, H. Du, X.T. Zeng and Y.C. Liu, “Magnetron sputtering of nanocomposite (Ti,Cr)CN/DLC coatings”, J Surf. Coat. Tech., Vol. 162, 2002, pp. 42-48.

[7]    C.F. Borges, E. Pfender and J. Heberlein, “Influence of nitrided and carbonitrided interlayers on enhanced nucleation of diamond on stainless steel 304”, J Diamond Relat Mater., Vol. 10, 2001, pp.1983-1990.

1. Erdemir, C. Donnet, Topical review; Tribology of diamond-like carbon films: recent progress and future prospects, J. Phys. D: Appl. Phys., Vol. 39, 2006, p. R311.

[8]    S. Kukiełka, W. Gulbiñski, Y. Pauleau, S.N. Dub, J.J. Grob, “Composition, mechanical properties and friction behavior of nickel/hydrogenated amorphous carbon composite films”, Surf. Coat. Technol., Vol. 200, 2006, pp. 6258-6262.

[9]    D.Y. Wang, K.W. Weng, Ch.L. Chang, X.J. Guo, “Tribological performance of metal doped diamond-like carbon films deposited by cathodic arc evaporation.”, Diam. Relat. Mater., Vol. 9, 2000, pp. 831-837.

[10]     X.M. He, M. Hakovirta, M. Nastasi, “Hardness, hydrophobic and optical properties of fluorine and boron co-alloyed diamond-like carbon films.” Mat. Lett., Vol. 59, 2005, pp. 1417-1421.

[11]     K. Kato, “Wear In Relation To Friction — A Review”, J Wear, Vol. 241, 2000, pp. 151-157.

[12]     W.P. Hsieh, “Characterization of the Ti-doped diamond-like carbon coatings on a type 304 stainless steel”, J vacuum sci. tech., Vol. 17, 1999, pp. 1053-1058.

[13]     L. Wang, J.F. Su and X. Nie, “Corrosion and tribological properties and impact fatigue behaviors of TiN- and DLC-coated stainless steels in a simulated body fluid environment”, J Sur. Coat. Tech., Vol. 205, 2010, pp. 1599-1605.

[14]     G. Cheng, D. Han, C. Liang, X. Wu and R. Zheng, “Influence of residual stress on mechanical properties of TiAlN thin films” J Surf. Coat. Tech., Vol. 228, 2013, pp. 328-330.

[15]     J. Lapin, “TiAl-based alloys: Present status and future perspectives”, J Metal., Vol.5, 2009, pp. 19-30.

[16]     C. Ruseta, E. Grigorea, G.A. Collinsb, K.T. Shortb, F. Rossic, N. Gibsonc, H. Dongd and T. Belld, “Characteristics of the Ti2N layer produced by an ion assisted deposition Method” J Surf. Coat. Tech., Vol. 174, 2003, pp. 698-703.

1. Tibrewala, “Piezoresistive Effect in Diamond-like Carbon Films”, 2006, Cuvillier Verlag, pp. 33-36.

[17]     J. C. Sánchez-López, M. Belin, C. Donnet, C. Quiros and E. Elizalde, “Friction mechanisms of amorphous carbon nitride films under variable environments: a triboscopic study”, Surf. coat tech., Vol. 16, 2002, pp.138-144.

[18]     R.A. Singh and E.S. Yoon, “Friction behaviour of diamond-like carbon films with varying mechanical properties”, J Surf. Coat. Tech., Vol. 201, 2006, pp, 4348-4351.

[19]     M. Sedlacek, B. Podornik, J. Vižintin, “Tribological properties of DLC coatings and comparison with test results: Development of a database”, Mater. Charact., vol. 59, 2008, pp. 151-161.

[20]     K. Adachi, N. Sodeyama and K. Kato, “Effect of humidity on friction of carbonnitride coatings under N₂ gas lubrication”, Proc. WTC II, WTC2005-64275, Sep.12-16, 2005, Washington, D.C., USA.

[21]     R. Hauert, L. Knoblauch-Meyer, G. Francz, A. Schroeder, E. Wintermantel, “Tailored aC: H coatings by nanostructuring and alloying”, Surf. Coat. Technol., Vol. 120-121, 1999, pp. 291-296.

[22]     J. Robertson, “Diamond-like amorphous carbon”, Mater. Sci. Eng. Report, Vol. 37, 2002, pp. 129-281.

[23]     J. Neidhardt, Z. Czigany, I.F. Brunell, L. Hultman, “Growth of fullerene-like carbon nitride thin solid films by reactive magnetron sputtering; role of low-energy ion irradiation in determining microstructure and mechanical properties.”, J Appl. Phys., Vol. 93, 2003, pp. 3002-3015.

[24]     I.A. Garcia, E. Berasategui, S.J. Bull, T.F. Page, J. Neidhardt, L. Hultman, N. Hellgren, “How hard is fullerene-like CNx Some observations from the nanoindentation response of a magnetron-sputtered coating.”, Philos. Mag. A , Vol. 82, 2002, pp., 2133-2147.

[25]     R. Gilmore, R. Hauert, “Control of the tribological moisture sensitivity of diamond-like carbon films by alloying with F, Ti or Si.” Thin Solid Films, Vol. 398, 2001, pp. 199-204.

K.P. Shaha, Y.T. Pei, C.Q. Chen, J.Th.M. De Hosson, “Synthesis of ultra-smooth and ultra-low friction DLC based nanocomposite films on rough substrates, Thin Solid Films”, Vol. 519, 2010, pp. 1618-1622.