Numerical Analysis of Circular Pre-notched U-Channel Section Distortions in Cold Roll-Forming Process

Subject Areas : Mechanical Engineering

S. Sattar ¹ , S. Mazdak ² , E. Sharifi ³

1 - Department of Mechanical Engineering, University of Tafresh, Iran
2 - Department of Mechanical Engineering, University of Tafresh, Iran
3 - Department of Mechanical Engineering, University of Tafresh, Iran

Received: 2017-03-02 Accepted : 2017-05-07 Published : 2017-08-24

Keywords:

References:

[1]   Halmos, G. T., “Roll Forming Handbook”, Taylor & Francis Group, 2006, Chap. 1.

[2]   Salmani Tehrani, M., Hartley, P., Moslemi Naeini, H., and Khademizadeh, H., “Localised edge Buckling in Cold Roll-forming of Symmetric Channel Section”, Thin-Walled Structures, Vol. 44, 2006, pp. 184–196.

[3]  Bhattacharyya, D., Smith, P. D., Yee, C. H., and Collins, L. F., “The Prediction of Deformation Length in Cold Roll Forming”, J. Mech. Work Tech., Vol. 9, 1984, pp. 181-191.

[4]   Chiang, K. F., “Cold Roll Forming”, ME Thesis, University of Auckland, 1984.

[5]   Brunet, M., Lay, B., and Pol, P., “Computer Aided Design of Roll Forming of a Channel Section”, J. Mater. Process Technol., Vol 60, 1966, pp. 209-214.

[6]   Watari, H., Ona, H., “Characteristic Features of Shape Defects Occurring in the Cold Roll Forming of Pre-notched Products”, Journal of Materials Processing Technology, Vol. 80–8, 1998, pp. 225-231.

[7]   Brunet, M., Lay, B., and Pol, P., “Computer Aided Design of Roll Forming of a Channel Section”, J. Mater. Process Technol., Vol 60, 1966, pp. 209-214.

[8]   Han, Z. H., “The Effects of Forming Parameters in the Roll Forming of a Channel Section with an outer Edge”, J. Mater. Process Technol., Vol. 116, 2001, pp. 205-210.

[9]       Lindgren, M., “Cold Roll Forming of a U-channel Made of High Strength Steel”, Journal of Materials Processing Technology, Vol. 186, 2007, pp. 77–81.

[10]    Chiang, K. F., “Cold Roll Forming”, ME Thesis, University of Auckland, 1984.

[11]    Bui, Q. V., Ponthot, J. V., “Numerical Simulation of Cold Roll Forming Processes”, Journal of Mater Process Technology, Vol, 202, 2008, pp. 275-282.

[12]     Zeng, G., Li, S. H., Yu, Z. Q., and Lai, X. M., “Optimization Design of Roll Profiles for Cold Roll Forming Based on Response Surface Method”, Materials and Design, Vol, 30, 2009, pp. 1930–1938.

[13]    Zeng, G., Li, S. H., Yu, Z. Q., and Lai, X. M., “Optimization Design of Roll Profiles for Cold Roll Forming Based on Response Surface Method”, Materials and Design, Vol, 30, 2009, pp. 1930–1938.

[14]     Watari, H., Ona, H., “Characteristic Features of Shape Defects Occurring in the Cold roll Forming of Pre-notched Products”, Journal of Materials Processing Technology, Vol. 80–8, 1998, pp. 225-231.

[15]    Brunet, M., Lay, B., and Pol, P., “Computer Aided Design of Roll Forming of a Channel Section”, J. Mater. Process Technol., Vol 60, 1966, pp. 209-214.

[16]    Han, Z. H., “The Effects of Forming Parameters in the Roll Forming of a Channel Section with an outer Edge”, J. Mater. Process Technol., Vol., 116, 2001, pp. 205-210.

[17]    Lindgren, M., “Cold Roll Forming of a U-channel Made of High Strength Steel”, Journal of Materials Processing Technology, Vol. 186, 2007, pp.77–81.

[18]    Chiang, K. F., “Cold Roll Forming”, ME Thesis,         University of Auckland, 1984.

[19]    Bui, Q. V., Ponthot, J. V., “Numerical Simulation of Cold Roll Forming Processes”, Journal of Mater Process Technology, Vol, 202, 2008, pp. 275-282.

[20]    Zeng, G., Li, S. H., Yu, Z. Q., and Lai, X. M., “Optimization Design of Roll Profiles for Cold Roll Forming Based on Response Surface Method”, Materials and Design, Vol, 30, 2009, pp. 1930-1938.

[21]    Moslemi Naeini, H., Bidabadi Shirani, B., Mazdak, S., Aziz Tafti, R., and Nemati Faghir, A., “Numerical Analysis of Effective Parameters on the Steel Profiles in Cold Roll Forming Process of Pre notch Sheets,” 20th annual international Iranian mechanical engineering conference, 2012.

[22]    Halmos, G. T., “Roll Forming Handbook”, Taylor & Francis Group, 2006, Chap. 4.

[23]    Handbook for Experimenters, Version 10.01., http://www.statease.com.

[24]    Shirani Bidabadi, B., “Numerical and Experimental Study of Transforming the Hole in Cold Roll Forming Process of Pre notch Section,” M.Sc. thesis, University of Tarbiat Modares, 2013.

[25]    Shirani Bidabadi, B., Moslemi Naeini, H., Azizi Tafti, R., and Mazdak, S., “Experimental Investigation of the Ovality of Holes on Pre-notched Channel Products in the Cold Roll Forming Process”, Journal of Materials Processing Technology, Vol. 225, 2015, pp. 213-220.