Investigation and Comparison of Microstructure and Mechanical Properties Between Parts of Shear Spinning and Rolled

Subject Areas : Journal of Environmental Friendly Materials

H Ghayour ¹ , S. M. J Hoseini ² , A Salemi Golezani ³ , M. K Asgarani ⁴ , I Ebrahimzadeh ⁵

1 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
2 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
3 - Advanced Materials Engineering Research Center, Karaj Branch, Islamic Azad University, Karaj, Iran
4 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
5 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran

Received: 2021-04-28 Accepted : 2021-11-01 Published : 2021-12-01

Keywords: Mechanical Properties, Copper, Rolling, Spinning, Shear Spinning,

References:

[1] J. R. Davis, S. D. Henry, B. R. Sanders, N. Hrivnak, J. A. Kinson and W. W. Scott, ASM Specialty Handbook, Copper and Copper Alloys, ASM International, (2001), 3.

[2] Z. Yanushkevich, A. Belyakov, R. Kaibyshev, C. Haase and D. A. Molodov, Deformation and Recrystallization Textures in a High-Mn Steel Subjected to Large Strain Cold Rolling, Proc. Int. Conf. Recrystallization Grain Growth (ReX&GG 2016), Pittsburgh, USA, (2016).

[3] P. Pawar, A. Pagar, A. Shah and S. Yevale, Review on Spinning Attachment to Lathe Machine, Int. Conf. on Ideas, Impact and Innovation in Mech. Eng., (ICIIIME 2017).

[4] L. Radović, M. Nikačević and B. Jordović, Trans. Nonferrous Met. Soc. China, 22, (2012), 991.

[5] C. C. Wong, T. Dean and J. Lin, Rev. , Int. J. Mach. Tools Manuf., 43, (2003), 1419.

[6] E. Hagan and J. Jeswiet, Rev. Proc. Inst. Mech. Eng. B, 217, (2003), 213.

[7] W. F. Hosford and R. M. Caddell, METAL FORMING: Mechanics and Metallurgy, Third Edition, Cambridge University Press, (2007).

[8] M. Sivanandini, S. Dhami and B. Pabla, Flow Forming Of Tubes-A Review, IJSER, 3(2012), 1.

[9] M. Zhan, X. Wang and H. Long, Mater. Des., 108, (2016), 207.

[10] X. Wang, M. Zhan, M. Fu, J. Guo, R. Q. Xu, X. P. Lei, Procedia Engineering, 207, (2017), 1725.

[11] M. Guillot, T. McCormack, M. Tuffs, A. Rosochowsk, S.Halliday and P. Blackwell, Procedia Eng., 207, (2017), 1719.

[12] Q. Liu and N. Hansen, Proc. R. Soc. Lond. A, 454, (1998), 2555.

[13] Y. Xu, H. Jiao, W. Qiu, R. D. K. Misra and J. Li, Mater., 1161, (2018), 1.

[14] X. Wang, P. Gao, M. Zhan, K. Yang, Y. Dong and Y. Li, Chinese J. Aeronaut., 33, (2020), 2088.

[15] C. Kubilay, Writer, Flow Forming Of Aeroengine Materials. [Performance]. Ph.D. Thesis Submitted in the University of Manchester, (2014).

[16] T. T. B. Wardoyo, S. Izman and D. Kurniawan, Appl. Mech. Mater., 315, (2013), 739.

[17] C. Deng, S. F. Liu, J. L. Ji, X. B. Hao, Z. Zhang and Q. Liu, J. Mater. Process. Technol., 214, (2014), 462.

[18] M. Haghshenas and R. J. Klassen, Mater. Sci. Eng. A, 641, (2015), 249.

[19] T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura and J. Jonas, Prog. Mater. Sci., 60, (2014), 130.

[20] M. Bacca, D. Hayhurst and M. R. McMeeking, Mech. Mater., 90, (2015), 148.

[21] F. Humphreys and M. Hatherly, Recrystallization and related annealing phenomena, 2 ed., Oxford: Elsevier, (2004), 11.

[22] H. Zhao, S. Ni, M. Song, X. Xiong, X. Liang and H. Li, Mater. Sci. Eng. A, 645, (2015), 328.

[23] Q. Xia, G. Xiao, H. Long, X. Cheng and B. Yang, Mater. Des., 59, (2014), 16.

[24] W. Xu, D. Shan, Z. Wang, G. Yang, Y. Lu and D. Kang, Trans. Nonferrous Met. Soc. China, 7, (2007), 1205.