Adapting Machining Strategies for the Sustainable Fabrication of Titanium Implants Using AHP and PROMETHEE

Subject Areas : Production Planning

Dimas Sorrenti Filho ¹ , Paulo Sergio de Arruda Ignácio ² , Rodrigo José Contieri ³

1 -
2 -
3 -

Received: 2025-02-27 Accepted : 2025-07-06 Published : 2025-07-06

Keywords: Sustainable manufacturing, Titanium implants, AHP-PROMETHEE, Multicriteria decision-making (MCDM),

Abstract :

This study proposes a sustainability-oriented optimization framework for the manufacturing of titanium ASTM F67 implants, integrating economic, environmental, and social indicators through a combined Analytic Hierarchy Process (AHP) and Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE II) approach. Two non-conventional machining technologies wire electrical discharge machining (WEDM) and abrasive waterjet cutting are analyzed, combined with milling and drilling operations to simulate 84 distinct manufacturing routes under varying demand scenarios (low, regular, high). Sustainability indicators, including energy consumption, CO₂ equivalent emissions, raw material utilization (titanium volume), and tool waste (carbide), are quantified and normalized. These are integrated alongside cost and operational safety metrics into the multicriteria decision-making framework. Energy consumption differs by up to 70% between the most and least efficient routes, while titanium utilization varies by 25%, directly impacting material costs and environmental footprint. The framework enables flexible weighting of criteria, accommodating different market or policy priorities. Results demonstrate that waterjet cutting combined with milling reduces energy consumption by up to 40% and titanium waste by 25% compared to WEDM routes under regular demand conditions, making it the most sustainable choice in such scenarios. Conversely, WEDM routes outperform in high-demand scenarios, achieving up to 35% higher productivity, despite elevated energy use. The framework offers a robust and adaptable decision-support tool, applicable not only to the biomedical sector but also scalable to other industries seeking to balance productivity and sustainability goals. This study delivers practical guidance for manufacturers and insights for policymakers aiming to promote sustainable manufacturing practices.

References:

Abd-Elaziem, W. et al. (2024) ‘Titanium-Based alloys and composites for orthopedic implants Applications: A comprehensive review’, Materials and Design, 241(December 2023), p. 112850. doi: 10.1016/j.matdes.2024.112850.
Arriaza, O., V., Kim, D., W.,Lee, D., Y., Suhaimi, M., A. Trade off analysis between machining time and energy consumption in impeller NC machining. Robotics and Computer-Integrated Manufacturing (2017), p.167-170.
Akshaya, S. et al. (2022) ‘Antibacterial Coatings for Titanium Implants: Recent Trends and Future Perspectives’, Antibiotics, 11(12). doi: 10.3390/antibiotics11121719.
Badgujar, P. P. and Rathi, M. G. (2014) ‘Abrasive Waterjet Machining-A State of Art’, IOSR Journal of Mechanical and Civil Engineering, 11(3), pp. 59–64. doi: 10.9790/1684-11365964.
Bhattacharyya, B.,Doloi, B.. Modern machining technology: advanced, Hibrid, micro machining and super finishing technology. Elsevier, 2020.
Banerjee, D. and Williams, J. C. (2013a) ‘Perspectives on titanium science and technology’, Acta Materialia. doi: 10.1016/j.actamat.2012.10.043.
Banerjee, D. and Williams, J. C. (2013b) ‘Perspectives on titanium science and technology’, Acta Materialia, 61(3), pp. 844–879. doi: 10.1016/j.actamat.2012.10.043.
Bania, P. J. (1994) ‘Beta titanium alloys and their role in the titanium industry’, Jom, 46(7), pp. 16–19. doi: 10.1007/BF03220742.
Chen, G. et al. (2019) ‘Effect of cutting edge radius and cooling strategies on surface integrity in orthogonal machining of Ti-6Al-4V alloy’, Procedia CIRP, 82, pp. 148–153. doi: 10.1016/j.procir.2019.04.056.
Cicha, I. et al. (2022) ‘Biosensor-Integrated Drug Delivery Systems as New Materials for Biomedical Applications’, Biomolecules, 12(9). doi: 10.3390/biom12091198.
Conde, J., Doria, G. and Baptista, P. (2012) ‘Noble Metal Nanoparticles Applications in Cancer’, Journal of Drug Delivery, 2012, pp. 1–12. doi: 10.1155/2012/751075.
‘CoroPlus®. Available online: https://www.sandvik.coromant.com/en- us/campaigns/coroplus (accessed on 03 August 2024)’ (2024), (August), p. 2024.
Hegab, H. A., Darras, B. and Kishawy, H. A. (2018) ‘Towards sustainability assessment of machining processes’, Journal of Cleaner Production, 170, pp. 694–703. doi: 10.1016/j.jclepro.2017.09.197.
Hourmand, M. et al. (2021) A Comprehensive Review on Machining of Titanium Alloys, Arabian Journal for Science and Engineering. Springer Berlin Heidelberg. doi: 10.1007/s13369-021-05420-1.
Huang, J., Ming Zhang K., Jia, Y. F.. Effect of thermal annealing on the microstructure, mechanical properties and resicual stress relaxation of pure titanium after deep rolling treatment. Jounal of Materials Science and Technology (2018), p.409-417.
Kiminami, Claudio Shyinti; CASTRO, Walman Benício de; OLIVEIRA, Marcelo Falcão de. Introdução aos processos de fabricação de produtos metálicos. São Paulo: Bluscher, 2013.
Li, S.J., Niinomi, M., Akahori, T., Kasuga, T., Yang, R., Hão, Y.L., Fatigue characteristics of bioactive glass-ceramic-coated Ti–29Nb–13Ta–4.6Zr for biomedical application, Biomaterials, V.25, p.3369-3378, 2004.
Inagaki, I. et al. (2014) ‘Application and Features of Titanium for the Aerospace Industry’, Nippon Steel & Sumitomo Metal Technical Report, (106), pp. 22–27.
Leal Filho, W. et al. (2019) ‘Using the sustainable development goals towards a better understanding of sustainability challenges’, International Journal of Sustainable Development and World Ecology, 26(2), pp. 179–190. doi: 10.1080/13504509.2018.1505674.
Ma, N. et al. (2020) ‘Research Progress of Titanium-Based High Entropy Alloy : Methods , Properties , and Applications’, 8(November), pp. 1–18. doi: 10.3389/fbioe.2020.603522.
Nguyen, V. (2024) ‘Optimizing Edm for Titanium Alloys : an in-Depth Comparison of Five Mcdm Techniques’, EUREKA: Physics and Engineering, (5), pp. 50–59. doi: 10.21303/2461-4262.2024.003283.
Pagone, E., Salonitis, K. and Jolly, M. (2020) ‘Automatically weighted high-resolution mapping of multi-criteria decision analysis for sustainable manufacturing systems’, Journal of Cleaner Production, 257, p. 120272. doi: 10.1016/j.jclepro.2020.120272.
Pałka, K. and Pokrowiecki, R. (2018) ‘Porous Titanium Implants: A Review’, Advanced Engineering Materials, 20(5), pp. 1–18. doi: 10.1002/adem.201700648.
Priarone, P. C., Robiglio, M. and Settineri, L. (2018) ‘On the concurrent optimization of environmental and economic targets for machining’, Journal of Cleaner Production, 190, pp. 630–644. doi: 10.1016/j.jclepro.2018.04.163.
Radomska-Zalas, A. (2023) ‘Experimental Research on the Use of a Selected Multi-Criteria Method for the Cutting of Titanium Alloy with an Abrasive Water Jet’, Materials, 16(15). doi: 10.3390/ma16155405.
Reitz, J., Lochbichler, C. and Friedrich, B. (2011) ‘Recycling of gamma titanium aluminide scrap from investment casting operations’, Intermetallics, 19(6), pp. 762–768. doi: 10.1016/j.intermet.2010.11.015.
Rotondo, A. et al. (2014) ‘Simulation-based decision support tools for demand disaggregation in a supply chain characterised by high routing flexibility’, Procedia CIRP, 25(C), pp. 261–268. doi: 10.1016/j.procir.2014.10.037.
Shaikh, M. B. N. et al. (2023) ‘An MCDM approach for multi-response optimisation of machining parameters in turning of EN8 steel (AISI-1040) for sustainable manufacturing’, International Journal on Interactive Design and Manufacturing, 17(6), pp. 3159–3176. doi: 10.1007/s12008-023-01368-8.
Slătineanu, L. et al. (2020) ‘Wire electrical discharge machining—a review’, Machines, 8(4), pp. 1–28. doi: 10.3390/machines8040069.
Thirumalai, R. and Senthilkumaar, J. S. (2013) ‘Multi-criteria decision making in the selection of machining parameters for Inconel 718’, Journal of Mechanical Science and Technology, 27(4), pp. 1109–1116. doi: 10.1007/s12206-013-0215-7.
Xu, L. J. et al. (2008) ‘The microstructure and properties of Ti-Mo-Nb alloys for biomedical application’, Journal of Alloys and Compounds, 453(1–2), pp. 320–324. doi: 10.1016/j.jallcom.2006.11.144.
Yildiz, Y. (2020) ‘Application of multi-criteria decision-making (MCDM) methods on a meso-scale electrical discharge drilling (EDD) process’, SN Applied Sciences, 2(11), pp. 1–14. doi: 10.1007/s42452-020-03668-0.