Experimental Study of the Effect of Laser-Cutting Process Parameters on Heat Distribution and Cutting Edge Quality of Steel Sheets

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

Mahsa  Mokhtarian ¹ (Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran)
Azam  Gasemi ² (Assistant Professor, Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran)

Received: 2018-04-11 Accepted : 2018-07-16 Published : 2018-02-01

Keywords:

References:

[1] Poprawe, R., Tailored Light. Springer, (2012).

[2] Chen, X., Li, T.,Zhai, K., Zhou, M., “Using orthogonal experimental method optimizing surface quality of CO2 laser cutting process for PMMA microchannels”, The International Journal of Advanced Manufacturing Technology, Vol. 88, No. 9-12, pp. 2727-2733, (2017).

[3] Shin, J.S., Oh, S.Y., Park, H., Chung C.M., Seon, S., Kim, T.S., Lee, L., Choi B.S., Moon, J.K., “High-speed fiber laser cutting of thick stainless steel for dismantling tasks”, Optics & Laser Technology, Vol. 94: pp. 244-247, (2017).

[4] Rodrigues, G.C. Duflou J.R., “Opportunities in laser cutting with direct diode laser configurations”, CIRP Annals-Manufacturing Technology, (2017).

[5] Niziev, V. and A. Nesterov, “Influence of beam polarization on laser cutting efficiency”, Journal of Physics D: Applied Physics, Vol. 32, No.13, p. 1455, (1999).

[6] Chen, K., Lawrence Yao Y., Modi V., “Numerical simulation of oxidation effects in the laser cutting process”, The International Journal of Advanced Manufacturing Technology, Vol. 15, No.11, pp. 835-842, (1999).

[7] Galantucci, L., Giusti F., “Excimer laser cutting: experimental characterization and 3D numerical modelling for polyester resins”, CIRP Annals-Manufacturing Technology, Vol. 47, No.1, pp. 141-144, (1998).

[8] Li, K., Sheng P., “Plane stress model for fracture of ceramics during laser cutting”, International Journal of Machine Tools and Manufacture, Vol. 35, No.11, pp. 1493-1506, (1995).

[9] Kaplan, A.F., “An analytical model of metal cutting with a laser beam”, Journal of applied physics, Vol. 79, No.5, pp. 2198-2208, (1996).

[10] Schulz, W., Becker, D., Franke, J., Kemmerling R., Herziger G., “Heat conduction losses in laser cutting of metals”, Journal of Physics D: Applied Physics, Vol. 26, No.9, p. 1357, (1993).

[11] Wee, L.M., Li L., “An analytical model for striation formation in laser cutting”, Applied Surface Science, Vol. 247, No.1, pp. 277-284, (2005).

[12] Chen, S.-L., “The effects of gas composition on the CO2 laser cutting of mild steel”, Journal of materials processing technology, Vol. 73, No.1, pp. 147-159, (1998).

[13] Karatas, C., Keles, O., Uslan I.,Usta Y., “Laser cutting of steel sheets: Influence of workpiece thickness and beam waist position on kerf size and stria formation”, Journal of Materials Processing Technology, Vol. 172, No.1, pp. 22-29, (2006).

[14] Wandera, C., Kujanpaa, V., “Characterization of the melt removal rate in laser cutting of thick-section stainless steel”, Journal of Laser Applications, Vol. 22, No.2, pp. 62-70, (2010)

[15] Eltawahni, H.A., Hagino, M., Benyounis, K.Y.,  Inoue, T., Olabic, A.G., “Effect of CO2 laser cutting process parameters on edge quality and operating cost of AISI316L”, Optics & Laser Technology, Vol. 44, No.4, pp 1068-1082, (2012).

[16]  Rao, S., Sethi, A., Kumar Das, A., Mandal, N., Kiran, P., Ghosh, R.,  Dixit, A. R.,  Mandal, A., “Fiber laser cutting of CFRP composites and process optimization through response surface methodology”, Materials and Manufacturing Processes, pp. 1-10, (2017).

[17] Madić, M., Antucheviciene., J.,  Radovanović, . M.,  Petković, D., “Determination of laser cutting process conditions using the preference selection index method”, Optics & Laser Technology, Vol. 89: pp. 214-220, (2016).

[18] Amjadi, M. S. , Foroozmehr, E. ,Badrossamay, M., “Study of heat-affected zone (HAZ) caused by cutting of Thin Ti-CP Sheet via CW CO2 Laser”, Modares Mechanical Engineering, Vol. 17, No. 5, pp. 253-259, (2017) (in Persian)

[19] Moradi, M., Ghoreishi, M., “Influences of laser welding parameters on the geometric profile of NI-base superalloy Rene 80 weld-bead”, The International Journal of Advanced Manufacturing Technology, Vol. 55, No. 1-4, pp. 205-215, (2011).

[20] Moradi, M., Mehrabi, O. , Azdast, T. , Benyounis, Kh. Y. , ”The effect of low power co2 laser cutting process parameters on polycarbonate cut quality produced by injection molding”, Modares Mechanical Engineering, Vol. 17, No. 2, pp. 93-100, (2017) (in Persian)

[21] DRÁBEK, M., Měření drsnosti řezných hran při laserovém dělení kovů. Brno Bakalářská práce. Vysoké učení technické v Brně, Fakulta strojního inženýrství, Ústav strojírenské technologie, 42 s., 1 příloha. Vedoucí práce RNDr. Libor Mrňa, Ph.D, (2012).

[22] Zhang, L., Michaleris, P., “Investigation of Lagrangian and Eulerian finite element methods for modeling the laser forming process”, Finite elements in analysis and design, Vol. 40, No. 4, pp. 383-405, (2004).

[23] Bergman, T. L., Lavine, A.S., Incropera, F.P., DeWitt, D.P., “Incropera, Fundamentals of heat and mass transfer”, John Wiley & Sons, (2011).

[24] Kothandaraman, C., Fundamentals of heat and mass transfer. New Age International, (2006).

[25] Ion, J., Laser processing of engineering materials: principles, procedure and industrial application. 2005: Butterworth-Heinemann, (2005).