-
حرية الوصول المقاله
1 - Effect of substrate temperature on ZnS films prepared by thermal evaporation technique
Rahul VishwakarmaAbstractThe nanocrystalline ZnS semiconducting thin films of 500 nm thickness have been deposited on glass substrate at different substrate temperatures (Ts) by thermal evaporation technique. The structural property of deposited thin films has been measured by X-ray dif أکثرAbstractThe nanocrystalline ZnS semiconducting thin films of 500 nm thickness have been deposited on glass substrate at different substrate temperatures (Ts) by thermal evaporation technique. The structural property of deposited thin films has been measured by X-ray diffraction, scanning electron microscopy, and Energy dispersive analysis of X-ray. The electrical and optical properties of thin films have been determined by D.C. two point probe and ultra-violet visible spectroscopy measurements. The X-ray diffraction patterns show that thin films have cubic structure. The electrical resistivity of thin films has decreased from 0.36 × 106 to 0.15 × 106 Ω cm as substrate temperature increases from 300 to 400 K. It shows that films have semiconducting in nature. The grain size and electrical conductivity of the thin films have increased as the deposition temperature increased while dislocation density, activation energy, and band gap decreased. The minimum band gap 3.43 eV has been found. تفاصيل المقالة -
حرية الوصول المقاله
2 - Effects of different gas flow rates and non-perpendicular incidence angles of argon cold atmospheric-pressure plasma jet on silver thin film treatment
Maryam Hosseinpour Akbar Zendehnam Seyedeh Mehri Hamidi Sangdehi Hamidreza Ghomi MarzdashtiAbstractIn this study, the influences of variations in the gas flow rate and incidence angles of argon cold atmospheric-pressure plasma jet on the morphology and absorption spectra of silver thin films (60 nm, 80 nm, and 100 nm film thickness) are investigated. To evalu أکثرAbstractIn this study, the influences of variations in the gas flow rate and incidence angles of argon cold atmospheric-pressure plasma jet on the morphology and absorption spectra of silver thin films (60 nm, 80 nm, and 100 nm film thickness) are investigated. To evaluate the surface morphology, atomic force microscopy (AFM) was employed on the silver thin film surface before and after plasma processing. To analyze the effect of plasma treatment on the grain size, the one-dimensional AFM surface profiles of Ag thin films are approximated using a Gaussian function. The absorbance of Ag thin films is measured in wavelength range of 190–1100 nm utilizing UV–Vis absorption spectrometer. Compared to the gas flow rates 0.5 standard litter per minute (SLM) and 2 SLM, surface treatment of Ag thin film with gas flow rate of 1 SLM increased the valley depth, the peak valley height, and the distance between two deepest valleys remarkably. A sequential argon plasma treatment (2-min plasma treatment perpendicular to surface was followed by 2-min plasma processing with non-perpendicular incidence angle of 60°) offers considerable improvement in the uniformity of grains and also changes shape of grains, especially the peak height (about 44 times higher than untreated sample) and area of grains (almost 136 times greater than untreated sample) which can be applicable for optical sensing technology. تفاصيل المقالة -
حرية الوصول المقاله
3 - Metallurgical Investigation of Under Water Friction Stir Welding (UWFSW) Process
M SadeghiUnderwater friction stir welding (FSW) has been demonstrated to be an effective method to improve the mechanical properties of joints. To illuminate the characteristics of underwater FSW, the microstructural evolution and its effect on mechanical performance of an under أکثرUnderwater friction stir welding (FSW) has been demonstrated to be an effective method to improve the mechanical properties of joints. To illuminate the characteristics of underwater FSW, the microstructural evolution and its effect on mechanical performance of an underwater joint were investigated in the present paper. This work compared the parameters of friction stir welding (FSW) and under water friction welding (UWFSW) on the weld joint .In this investigating Friction stir welding (FSW) used in under water environment, for this Operations research pin covered and shielded from contact water by hollow shaft spin (HSS), the HSS controlled the heat conduction of pin and disconnect with water, applying for the first time a novel under water FSW technique developed at marine structures.The novel technique acceptance given by the experimental setup on Al X4000 series, for studied the mechanical and metallographic exams. The metallographic exams indicate that weld nugget grain size has been decreased. The mechanical testing illustrated hardness and tensile strength have been increased, on the other hand the percentage of elongation and impact energy have been decreased. تفاصيل المقالة -
حرية الوصول المقاله
4 - Modelling of Friction Stir Extrusion using Artificial Neural Network (ANN)
Mohammad Ali Ansari Reza Abdi Behnagh Dong Lin Sarang KazeminiaIn the present study, an artificial neural network (ANN) model is developed to predict the correlation between the friction stir extrusion (FSE) parameters and the recycled wires’ average grain sizes. FSE is a solid–state synthesis technique, in which machin أکثرIn the present study, an artificial neural network (ANN) model is developed to predict the correlation between the friction stir extrusion (FSE) parameters and the recycled wires’ average grain sizes. FSE is a solid–state synthesis technique, in which machining chips are firstly loaded into the container, and then a rotating tool with a central hole is plunged into the chips at a selected rotational speed and feed rate to achieve indirect extrusion. Selecting rotational speed (RS), vertical speed (VS), and extrusion hole size (HS) as the input and average grain size as the output of the system, the 3–6–1 ANN is used to show the correlation between the input and output parameters. Checking the accuracy of the neural network, R squared value and Root–Mean–Square–Error (RMSE) of the developed model (0.94438 and 0.75794, respectively) have shown that there is a good agreement between experimental and predicted results. A sensitivity analysis has been conducted on the ANN model to determine the impact of each input parameter on the average grain size. The results showed that the rotational speed has more effect on average grain size during the FSE process in comparison to other input parameters. تفاصيل المقالة -
حرية الوصول المقاله
5 - تعیین شدت بیابانزایی بر اساس شاخصهای طیفی با استفاده از تصاویر سنتینل-2 (منطقه مورد مطالعه: استان سیستان و بلوچستان)
فرهاد ذوالفقاری وحیده عبداللهیپیشینه و هدف سطوح مختلف پوشش گیاهی آلبدوی متفاوتی دارند. از طرفی آلبدوی سطحی یکی از مهمترین مؤلفههای تعادل تابش سطحی است که با بررسی رفتار آن میتوان به شدت تخریب و بیابانزایی پی برد. پوشش گیاهی به دلیل اینکه عاملی برای پایداری سطح زمین محسوب میشود میتواند یکی از م أکثرپیشینه و هدف سطوح مختلف پوشش گیاهی آلبدوی متفاوتی دارند. از طرفی آلبدوی سطحی یکی از مهمترین مؤلفههای تعادل تابش سطحی است که با بررسی رفتار آن میتوان به شدت تخریب و بیابانزایی پی برد. پوشش گیاهی به دلیل اینکه عاملی برای پایداری سطح زمین محسوب میشود میتواند یکی از مهمترین مؤلفههای کلیدی در مناطق خشک برای کاهش اثرات فرسایش و بیابانزایی بهحساب آید. گسترش بیابانزایی و تغییر در میزان پوشش گیاهی بهنوبه خود ازجمله عوامل تغییر در آلبدو به شمار میروند. هدف از این مطالعه تعیین شدت بیابانزایی بر اساس شاخصهای طیفی آلبیدو (Albedo)، اندازه دانه خاک سطحی (TGSI) و شاخص نرمالشده تفاضل پوشش گیاهی (NDVI) با استفاده از فناوری سنجشازدور میباشد. شناسایی مناطق تخریب شده در کوتاهترین زمان و با کمترین هزینه با استفاده از تصاویر سنتینل-2 با قدرت تفکیک مکانی 10 متری از اهداف این پژوهش میباشد. در این پژوهش برای اولین بار در منطقه سیستان و بلوچستان بر اساس شاخصهای طیفی با استفاده از تصاویر سنتینل-2، بهترین شاخص برای پایش شدت بیابانزایی در مناطق خشک معرفی خواهد شد.مواد و روش ها برای ارزیابی شدت بیابانزایی و شناخت شاخص مناسب برای تهیه نقشه شدت بیابانزایی گامهای زیر انجام گرفت؛ 1) انتخاب تصاویر و انجام عملیات پیشپردازش تصاویر با استفاده از نرمافزار SNAP. 2) محاسبه شاخصهای TGSI، NDVI و Albedo، 3) بررسی رابطه همبستگی بین شاخصها با استفاده از نرمافزار SPSS®24، 4) تهیه نقشه شدت بیابانزایی منطقه و به دست آوردن معادله شدت بیابانزایی با استفاده از نرمافزار ArcGIS®10.3. در گام اول این پژوهش دادههای ماهواره Sentinel-2A مربوط به سنسور MSIL-1C 20 اوت سال 2020 انتخاب شد. تصاویر بهگونهای انتخاب گردید که فصل رویش گیاهان یکساله و موقتی نباشد و همچنین روزی انتخاب شد که پوشش ابری وجود نداشته باشد تصاویر مورد نیاز از سایت http://scihub.copernicus.eu/ دانلود و مورد استفاده قرار گرفت.نتایج و بحث نتایج حاصل از مدل رگرسیون خطی بین دو شاخص NDVI و Albedo نشان داد که این دو شاخص با یکدیگر دارای همبستگی منفی میباشند و به ترتیب میزان ضریب همبستگی در منطقه سوران و زابل برابر با 0.76 و 0.63 بود. نتایج نشان داد که با افزایش میزان شاخص NDVI از میزان شاخص آلبدو کاسته میشود. همچنین نتایج حاصل از مدل رگرسیون خطی بین دو شاخص TGSI و Albedo نشان داد که این دو شاخص با یکدیگر رابطه قوی و مثبتی داشته و به ترتیب میزان ضریب همبستگی برای منطقه سوران و زابل برابر با 0.78 و 0.81 بود. نتایج نشان داد که با افزایش میزان شاخص TGSI بر میزان شاخص آلبدو افزوده میشود.شدت بیابانزایی در مناطق مورد مطالعه بر اساس معادله تعیین گردید و با استفاده از روش شکست طبیعی جنکس (Natural Breaks Jenks) در نرمافزار ArcGIS شدت بیابانزایی به 5 درجه؛ مناطق بدون بیابانزایی، مناطق با شدت کم بیابانزایی، مناطق با شدت متوسط بیابانزایی، مناطق با شدت زیاد بیابانزایی، و مناطق با شدت خیلی زیاد بیابانزایی تقسیم گردید. در این پژوهش بر اساس دادههای ماهواره سنتینل-2 شاخصهای Albedo، NDVI و TGSI استخراج گردید. نتایج بررسی رگرسیون خطی بین دو شاخص NDVI و Albedo نشان داد که یک رابطه منفی و قوی بین این دو شاخص وجود دارد که با نتایج پژوهشهای مشابه مطابقت دارد. نتایج حاصل از همبستگی بالا و منفی بر اساس این دو شاخص به این مفهوم است که هر گونه افزایش در مقدار شاخص پوشش گیاهی NDVI منجر به کاهش در میزان آلبدوی سطح خواهد شد. از طرفی مناطق با آلبدوی بالا بیانگر تخریب پوشش گیاهی و برهنه بودن خاک میباشد. در مناطقی که کلاس شدت زیاد بیابانزایی مشاهده گردید مقدار شاخص آلبدوی سطحی بالا میباشد و مقدار شاخص پوشش گیاهی کم است. طبقهبندی شدت بیابانزایی در منطقه سیستان بر اساس مدل Albedo-NDVI نشان میدهد که 27.73 درصد منطقه در کلاس بدون شدت بیابانزایی، 18.03 درصد در کلاس کم شدت، 32.92 درصد از منطقه از نظر بیابانزایی در کلاس شدت متوسط بیابانزایی، 20.3 درصد در کلاس شدید و تنها 1.02 درصد از منطقه در کلاس خیلی شدید بیابانزایی قرار گرفته است. همچنین طبقهبندی شدت بیابانزایی در سوران بر اساس مدل Albedo-NDVI نشان میدهد که 4.82 درصد منطقه بدون شدت بیابانزایی، 8.44 درصد در کلاس کم، 50.97 درصد از منطقه از نظر بیابانزایی در کلاس شدت متوسط، 34.48 درصد در کلاس شدید و 1.3 درصد از منطقه در کلاس خیلی شدید بیابانزایی قرار گرفته است. بیشترین درصد شدت بیابانزایی مربوط به کلاس شدت متوسط میباشد. نتایج رگرسیون خطی بین دو شاخص TGSI و Albedo نیز نشان داد که یک رابطه مثبت و قوی بین این دو شاخص وجود دارد. نتایج بیانگر این است که رابطه بین شاخص TGSI و Albedo نسبت به رابطه بین دو شاخص NDVI و Albedo قویتر و از ضریب همبستگی بالاتری در هر دو منطقه برخوردار میباشد که از دلایل عمدۀ آن میتوان به پراکندگی پوشش گیاهی در مناطق خشک اشاره نمود. رابطه شاخص TGSI با Albedo خصوصیات فضایی مناطق عاری از پوشش گیاهی و همچنین مناطق با پوشش گیاهی خیلی کم را برای تعیین شدت بیابانزایی بهتر نشان میدهد. شاخص TGSI منعکس کننده اندازه ذرات درشت خاک سطحی میباشد که رابطه مثبتی با ذرات ریز محتوای ماسه خاک سطحی دارد. هر چه اندازه ذرات خاک سطحی درشت دانهتر باشد میزان بیابانزایی شدت بیشتری خواهد داشت. در مناطقی که محتوای زیاد ماسه ریز در اندازه ذرات خاک سطحی وجود داشته باشد مقادیر بالای شاخص TGSI قابل مشاهده خواهد بود.نتیجه گیری در این پژوهش ما با استفاده از تکنیک سنجش از راه دور و بر اساس تصاویر چند طیفی سنتینل-2 برای اولین بار در ایران به استخراج شدت بیابانزایی در دو منطقه متفاوت از استان خشک سیستان و بلوچستان پرداختیم. بر اساس بازتاب طیفی اتفاق افتاده از سطح زمین و قدرت تفکیک مکانی 10 متری شدت بیابانزایی را در دو منطقه مورد مطالعه قرار دادیم. بر اساس نتایج این پژوهش پیشنهاد میگردد بهصورت ترکیبی از دو مدل Albedo-NDVI و Albedo-TGSI برای پایش و تهیه نقشههای شدت بیابانزایی در مناطق خشک ایران استفاده گردد. نتایج این پژوهش نشان داد که مناطق بدون بیابانزایی و شدت کم بیابانزایی بر اساس مدل Albedo-TGSI به نحو مطلوبتری نشان داده میشوند. تفاصيل المقالة -
حرية الوصول المقاله
6 - مدلسازی و مطالعه اثر هندسه قطعه و اندازه دانه بندی درعملیات حرارتی فولاد 1050 به کمک نرم افزارAC3
مهدی رفیعیدر این مقاله تاثیر هندسه قطعه و اندازه دانه بندی ریزساختار در عملیات حرارتی فولاد 1050 مورد بررسی قرار گرفته است بدین منظور دو نمونه قطعه کار با مقطع گرد (استوانه ای) و مربعی (تخت) برای شبیه سازی با نرم افزار AC3 در نظر گرفته شد و تاثیر هر کدام بر روی رشد اندازه دانه ها أکثردر این مقاله تاثیر هندسه قطعه و اندازه دانه بندی ریزساختار در عملیات حرارتی فولاد 1050 مورد بررسی قرار گرفته است بدین منظور دو نمونه قطعه کار با مقطع گرد (استوانه ای) و مربعی (تخت) برای شبیه سازی با نرم افزار AC3 در نظر گرفته شد و تاثیر هر کدام بر روی رشد اندازه دانه ها در محیط های خنک کننده مختلف مورد بررسی قرار گرفت همچنین بررسی سختی در سطح و عمق برای هر دو حالت ارزیابی گردید. نتایج حاصل از شبیه سازی نشان می دهد که نرم افزار بکارگرفته شده قابلیت مناسبی برای پیش بینی سختی در سطح و عمق، اندازه دانه بندی و رفتار منحی های CCT و سرد شدن در عملیات حرارتی فولاد 1050 دارد و این شیوه می تواند در مقیاس کارگاهی و در کاربردهای صنعتی به کار گرفته شود. تفاصيل المقالة -
حرية الوصول المقاله
7 - Modelling Dependency of the Steady-State Grain Size on the Stacking Fault Energy in Severely Plastic Deformed Materials
Maryam Bahmanpour Majid AbdellahiIn the present work, a computer-based method is proposed to investigate the relationship between the steady-state grain size (ds) and stacking fault energy (SFE) in severely plastic deformed (SPDed) materials. The stacking fault energy, γ, plays an important role أکثرIn the present work, a computer-based method is proposed to investigate the relationship between the steady-state grain size (ds) and stacking fault energy (SFE) in severely plastic deformed (SPDed) materials. The stacking fault energy, γ, plays an important role in determining the mechanical properties of face-centered cubic (fcc) metals. A number of models have been proposed to show this role. These models have several shortcomings, including complex computational variables, data constraints and small computational range constraints. The present model compatible with experimental results does not employ hard calculable variables. Besides, it is applicable not only for pure metals but also for alloys. The squared regression (R2) and error sum of squares (SSE) for the training and testing data of the presented model are 0.93, 0.0006 and 0.98, 0.00018, respectively, which indicates the high accuracy of the proposed model. The slope of the versus is about 0.6453 which is comparable to all the models offered in this field. تفاصيل المقالة -
حرية الوصول المقاله
8 - Finite Element Modeling of Strain Rate and Grain Size Dependency in Nanocrystalline Materials
Minoo TabanfardNanocrystalline materials show a higher strain-rate sensitivity in contrast to the conventional coarse-grained materials and a different grain size dependency. To explain these phenomenon, a finite element model is constructed that considers both grain interior and grai أکثرNanocrystalline materials show a higher strain-rate sensitivity in contrast to the conventional coarse-grained materials and a different grain size dependency. To explain these phenomenon, a finite element model is constructed that considers both grain interior and grain boundary deformation of nanocrystalline materials. The model consist of several crystalline cores with different orientations and grain boundary phase. The nonlinear behavior of the nanocrystalline core is implemented by a grain size dependent crystal plasticity. The boundary phase is assumed to have the mechanical properties of quasi-amorphous material. The constitutive equations for both grains interior and boundary phase are implemented into the finite-element software Abaqus. A calibration procedure was used to tune some parameters of the model with the previously published experimental data on the nanocrystalline copper. Then the model is used to predict the material behavior in various strain rates and grain sizes. The stresses obtained from these simulations match well with the experimental data for nanocrystalline copper at different strains and strain rates. Deviation from the Hall-Petch law and inverse Hall-Petch effect are also well illustrated by the model. تفاصيل المقالة -
حرية الوصول المقاله
9 - An investigation on full annealing temperature and annealing twins’ Density in Fe-33Mn-3Si-2Al high-manganese steel
Gh.R Razavi A Ansaripour H Monajatizadeh M.R ToroghinejadTwinning induced plasticity (TWIP) steels with high manganese percentage (17-35%), are mostly used in automotive bodies. Their microstructure at room temperature is austenitic, and due to the low stacking fault energy, major deformation mechanism in them is twinning ins أکثرTwinning induced plasticity (TWIP) steels with high manganese percentage (17-35%), are mostly used in automotive bodies. Their microstructure at room temperature is austenitic, and due to the low stacking fault energy, major deformation mechanism in them is twinning inside austenite grains which leads to enhanced mechanical strength in the steel. Due to the important effect of heat treatment process on mechanical properties, full annealing heat treatment and resultant twins were investigated in this study. To this aim, the steel was casted, hot rolled, and then heat treated at different times and temperatures and the obtained microstructures were analyzed using optical microscope. The results showed that the percentage of annealing twins is increased with increasing annealing temperature up to 1100 °C, the peak point at which grain growth stage starts, and increasing temperature above that decreases twins’ percentage. A relation between grain size and annealing twins’ percentage was found. Full annealing temperature for this steel was determined to be 1100 °C. تفاصيل المقالة -
حرية الوصول المقاله
10 - تأثیر تکتونیک بر مورفومتری و جورشدگی رسوبات بستر رودخانه قشلاق
هادی نیری خبات امانی اختر امانیفعالیت های زمین ساختی در خرد شدن سنگ ها مؤثر بوده و غالباً باعث تغییر در مورفومتری و جورشدگی رسوبات رودخانه ها می شوند. هدف پژوهش حاضر مطالعه و بررسی تأثیر تکتونیک و گسل های فعال بر بافت و جورشدگی بار رسوبی رودخانه قشلاق در حدفاصل سدهای قشلاق و ژاوه با استفاده از روش تو أکثرفعالیت های زمین ساختی در خرد شدن سنگ ها مؤثر بوده و غالباً باعث تغییر در مورفومتری و جورشدگی رسوبات رودخانه ها می شوند. هدف پژوهش حاضر مطالعه و بررسی تأثیر تکتونیک و گسل های فعال بر بافت و جورشدگی بار رسوبی رودخانه قشلاق در حدفاصل سدهای قشلاق و ژاوه با استفاده از روش توصیفی- تحلیلی است. جهت نیل به اهداف موردنظرابتدا مطالعات میدانیصورت گرفته و از ابزارهایی مانند نقشه های توپوگرافی 1:25000، نقشه زمینشناسی 1:100000 و گزارش های موجوداستفاده شد. روش کار بدینصورت بود کهدر محدوده تقاطع گسل ها و رودخانه نمونه های رسوب برداشت شد. پس از خشک شدن، در دستگاه شیکردر هفت مقیاس غربال گردیده وشاخص های موقعیت و پراکندگی مربوط به هرکدام از نمونه ها محاسبه شد. نتایج نشان می دهد که گسل ها سبب افزایش شیب بستر و افزایش نیرو و سرعت آبشدهکه نتیجه آن حمل انتخابی ذرات رسوب و کاهش شدید جورشدگی است. تفاصيل المقالة -
حرية الوصول المقاله
11 - Distribution and Grain Size Support-Dependent Catalytic Properties of Iridium Nanoparticles
Zahra Amirsardari Akram Dourani Mohamad Ali Amirifar Nooredin Ghadiri Massoom Babak AfzaliThe catalytic reaction of iridium nanoparticles was carried out over gamma-alumina granules to investigate the factors controlling the catalytic activities. The evaluation of iridium nanoparticle activity in the laboratory reactor was done for support grains with differ أکثرThe catalytic reaction of iridium nanoparticles was carried out over gamma-alumina granules to investigate the factors controlling the catalytic activities. The evaluation of iridium nanoparticle activity in the laboratory reactor was done for support grains with different diameter between 1 mm to 4 mm. The characterization of three iridium catalysts was evaluated by XRD, FESEM and EDX before and after catalytic activity. The rate of hydrazine decomposition increased to 306 h-1 with the better distribution of nanoparticles, regardless of the grain size of catalyst support, whereas the hydrazine decomposition rate was larger for smaller supported catalyst. The probability of hydrazine monohydrate molecules in contact with active sites becomes higher and the movement of reactants and gas products will be easy inside and outside the pores, leading to the increase in reactivity. The rate of the hydrazine monohydrate decomposition and H2 selectivity decreased to 216 h-1 and 26% with the lower catalyst grains and the higher size of support along with worse distribution on the surface. The remarkable results of the results prove that support granule size is a dominant factor in the catalytic decomposition. تفاصيل المقالة -
حرية الوصول المقاله
12 - Distribution and Grain Size Support-Dependent Catalytic Properties of Iridium Nanoparticles
Zahra Amirsardari Akram Dourani Mohamad Ali Amirifar Nooredin Ghadiri Massoom Babak AfzaliThe catalytic reaction of iridium nanoparticles was carried out over gamma aluminagranules to investigate the factors controlling the catalytic activities.The evaluation of iridium nanoparticle activity in the laboratory reactor wasdone for support grains with different أکثرThe catalytic reaction of iridium nanoparticles was carried out over gamma aluminagranules to investigate the factors controlling the catalytic activities.The evaluation of iridium nanoparticle activity in the laboratory reactor wasdone for support grains with different diameters between 1 mm to 4 mm. Thecharacterization of three iridium catalysts was evaluated by XRD, FESEM andEDX before and after catalytic activity. The rate of hydrazine decomposition andhydrogen selectivity increased to 306 h-1 and 42% with the better distributionof nanoparticles, regardless of the grain size of catalyst support, whereas thehydrazine decomposition rate was larger for smaller supported catalysts. Theprobability of hydrazine monohydrate molecules in contact with active sitesbecomes higher and the movement of reactants and gas products will be easyinside and outside the pores, leading to the increase in reactivity. The rate of thehydrazine monohydrate decomposition and H2 selectivity decreased to 216 h-1and 26% with the lower catalyst grains and the higher size of support along withworse distribution on the surface. The remarkable results of results prove thatsupport granule size is a dominant factor in catalytic decomposition. تفاصيل المقالة -
حرية الوصول المقاله
13 - Investigation of the Effect of Ferrite Grain Size on Acoustic Emission Signals
Mehdi Khosravi Ramin KhamediIn this study, the effect of ferrite grain size on mechanical properties and failure micro-mechanisms of materials was investigated by using acoustic emission (AE) non-destructive testing (NDT). AE signals were obtained from tensile tests of fully annealed ferrite sampl أکثرIn this study, the effect of ferrite grain size on mechanical properties and failure micro-mechanisms of materials was investigated by using acoustic emission (AE) non-destructive testing (NDT). AE signals were obtained from tensile tests of fully annealed ferrite samples and the effective AE parameters for each sample were analyzed from the AE waveforms. Due to annealing, the ferrite grain size was different in each sample, which affected the AE signals, and to analyze the AE signals, the Sentry Function (SF) and Fast Fourier Transform (FFT) were used and the results show that performing a full annealing operation to change the grain size at different temperatures almost did not significantly affect the frequency parameter, which has a range of about 175 kHz. In addition, the amplitude was about 30-40 dB, which indicates the deformation of the ferrite, and also the amount of AE energy released during the tensile test was lower than the strain energy. تفاصيل المقالة -
حرية الوصول المقاله
14 - تاثیر اکسیدنیوبیوم (Nb2O5)بر روی رفتار تف جوشی کامپوزیت Al2O3-ZrO2
حسین خوارزمی پور خلیل رنجبردر این تحقیق تاثیر افزودن اکسید نیوبیوم بر ریز ساختار و پایداری فاز زیرکونیا در نمونه تف جوشی کامپوزیت آلومینا- زیرکونیا پس از آسیابکاری مکانیکی مورد بررسی قرار گرفت. بدین منظور از پودر های آلومینا و زیرکونیا به عنوان مواد اولیه و از پودر اکسیدنیوبیوم به عنوان ماده افزو أکثردر این تحقیق تاثیر افزودن اکسید نیوبیوم بر ریز ساختار و پایداری فاز زیرکونیا در نمونه تف جوشی کامپوزیت آلومینا- زیرکونیا پس از آسیابکاری مکانیکی مورد بررسی قرار گرفت. بدین منظور از پودر های آلومینا و زیرکونیا به عنوان مواد اولیه و از پودر اکسیدنیوبیوم به عنوان ماده افزودنی استفاده شد. تمام کامپوزیت های آلومینا-زیرکونیا دارای زیرکونیا ثابت برابر با 10درصدوزنی هستند و اکسید نیوبیوم به میزان 1درصدوزنی به نمونه های کامپوزیت افزوده شد. پودرهای کامپوزیت بصورت محوری تحت فشار درون قالب قرص مانند قرار گرفتند، سپس نمونه ها در دمای 1300 تا 1500 درجه سانتیگراد به مدت دو ساعت درون کوره عملیات حرارتی تف جوشی شدند. در شناسایی فازها از پراش اشعه ایکس و برای بررسی ریزساختارها از میکروسکوپ الکترونی روبشی استفاده شد. بررسی ها و نتیجه آزمایشات نشان داد که اکسید نیوبیوم تاثیر شگرفی بر چگالی تف جوشی دارد و چگالی را تا 75/3 گرم بر سانتیمترمکعب افزایش داد. از طرفی دیگر اندازه دانه های زمینه پس از تف جوشی تا 19/2 میکرون افزایش یافته و از میزان فاز های تتراگونال به میزان زیادی کاسته شد. در این تحقیق تاثیر این اکسید بر مکانیزم تف جوشی کامپوزیت آلومینا- زیرکونیا و همچنین پایداری فاز تتراگونال زیرکونیا مورد بحث و تحلیل قرار گرفته است. تفاصيل المقالة -
حرية الوصول المقاله
15 - The Effect of Heat Treatment on Springing of AISI301
Majid Karimian Ehsan Nourouzi Esfahani Mohammad BagherboomAISI 301 stainless steel is a frequently used metal, especially in high temperature demands and or in part with high corrosion risk. Thin spring steel plates can be used as expansions of heat furnaces insulation and variety of all other springs. The present study has as أکثرAISI 301 stainless steel is a frequently used metal, especially in high temperature demands and or in part with high corrosion risk. Thin spring steel plates can be used as expansions of heat furnaces insulation and variety of all other springs. The present study has assessed the effects of temperature and thermal treatment time span on the microstructure of stainless steel 301 to achieve elasticity and found out that microstructure gets smaller. As well as the Martensitic ά phase in the sample distributes uniformly after thermal treatment at 450 ºC for 20 minutes then water quenched in 10 ºC. By using X-ray diffraction, it can be found that the reduction in crystalline size of the Martensite ά and increasing in Martensite volume fraction is the cause of the elasticity of the samples. All obtained results confirmed by Ferittscope test. تفاصيل المقالة