Numerical and Experimental Analysis of Temperature Field, Deformation, and Residual Stress in Two-Stage Single-Pulse Sub-Powder Welding Joints
Subject Areas :
1 - Department of Mechanical Engineering, Faculty of Engineering, Payame Noor University, Tehran, Iran
Keywords: Submerged arc Welding (SAW), Finite Element Method, Residual Stress, Temperature Distribution,
Abstract :
This study investigates the temperature fields, distortion, and distribution of residual stresses in single-pulse sub-powder welding of structural steel. Both experimental and three-dimensional finite element modeling approaches were employed. The heat flux from the welding process was applied as a combination of volumetric and surface heat sources in a Fortran-based program. The indirect coupled method in Abaqus software was utilized for the elastoplastic analysis of the welding process. The dimensions of the molten pool and the heat-affected zone were measured experimentally using metallography and compared with the finite element model. The temperature fields and distortion obtained from the finite element model were also validated against the experimental results. Finally, the influence of constraints on the degree of distortion and residual stresses in the analyzed structure was examined. The comparison of the numerical and experimental results shows good agreement, demonstrating the modeling approach's ability to accurately predict temperature distribution, deformation, and residual stresses in the sub-powder welding process.
[1] Hassanifard, S., Nabavi-Kivi, A., Ghiasvand, A. and Varvani-Farahani, A. 2021. Monotonic and fatigue response of heat-treated friction stir welded Al 6061-T6 joints: Testing and characterization. Materials Performance and Characterization. 10(1):353-369. doi: 10.1520/MPC20200076.
[2] Yaghi A., Hyde T. H., Becker A. A., Sun W. and Williams J. A. 2006. Residual stress simulation in thin and thick-walled stainless steel pipe welds including pipe diameter effects. International Journal of Pressure Vessels and Piping. 83(11): 864-874. doi:10.1016/j.ijpvp.2006.08.014.
[3] Li, J.Q. and Liu, H.J. 2015. Effects of the reversely rotating assisted shoulder on microstructures during the reverse dual-rotation friction stir welding. Journal of Materials Science & Technology. 31(4):375-383. doi:10.1016/j.jmst.2014.07.020.
[4] Liu, H.J., Li, J.Q. and Duan, W.J. 2013. Research on reverse dual rotation friction stir welding process. In Proceedings of the 1st international joint symposium on joining and welding. Woodhead Publishing, 25-32. doi:10.1533/978-1-78242-164-1.25.
[5] Sun, L., Ren, X. and Hi, J., 2021. Numerical investigation of a novel pattern for reducing residual stress in metal additive manufacturing. Journal of Materials Science & Technology. 67:11-22. doi:10.1016/j.jmst.2020.05.080.
[6] Thomas, W.M., Staines, D.J., Watts, E.R. and Norris, I.M. 2005. The simultaneous use of two or more friction stir welding tools. Abington, Cambridge, TWI published on the Internet.
[7] Nakhodchi, S. Akbari, S., Shokufar A. and Rezazadeh, H. 2014. Numerical and experimental study of temperature and residual stress in multi-pass welding of two stainless steel plates having different thicknesses. 14(9):81-89. doi: 20.1001.1.10275940.1393.14.9.14.9.
[8] Goldak J., Chakravarti A. and Bibby M., 1984. A new finite element model for welding heat sources. Metallurgical Tranactions B, Vol. 15B, P. 299-305. doi: 10.1007/BF02667333.
[9] Kazemi, M., 2021. Investigation of the effect of welding path on residual stresses and deformations in peripheral welding of steel pipe. Amirkabir Journal of Mechanical Engineering. 53:641-644. doi: 10.22060/mej.2020.18166.6752.
[10] Baharin, A., Yousef, H. and Bernd, M. 2022. Residual stresses in gas tungsten arc welding: a novel phase-field thermo-elastoplasticity modeling and parameter treatment framework. Computational Mechanics. 69:565-587. doi: 10.1007/s00466-021-02104-3.
[11] Sharyari, Z. Laribaghal, M. and Gheysari, K. 2023. Finite Element Simulation of Temperature Field and Residual Stress Induced by Surface Welding Process of Mild Steel. Journal of Manufacturing Innovations. 1:37-51. doi:10.22055/jomi.2024.39850.1005.