Ti-6Al-4V Synthesized by Mechanical Alloy Method and Mechanical and Bioactivity Properties of Ti-6Al-4V/HA-Clay Nano composite

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

محمدعلی مطلبی ¹ , ابراهیم کرمیان ² , مجید کریمیان ³

1 - کارشناس ارشد، مهندسی مکانیک، دانشگاه آزاد اسلامی واحد خمینی شهر
2 - استادیار، دانشکده مکانیک، پژوهشکده مواد، دانشکده مواد، دانشگاه آزاد اسلامی واحد نجف آباد
3 - استادیار، دانشکده مکانیک، دانشگاه آزاد اسلامی واحد خمینی شهر

Received: 2016-03-05 Accepted : 2016-05-16 Published : 2016-10-22

Keywords: clay, hydroxyapatite, mechanical alloying, Nano powder, Ti alloy,

Abstract :

Nowadays, titanium-based alloys are among the most attractive metallic materials for biomedical applications (as implants) due to their non-biodegradability, low density, good mechanical properties as well as their good biocompatibility. Hydroxyapatite (Ca10 (PO4)6(OH)2, HA) has been widely used for biomedical applications due to its bioactive, biocompatible and osteoconductive properties. Firstly, Ti-6Al-4V alloy was synthesized by mechanical alloy method with high energy ball milling plantery, HEBM. And then in this work began with preparing hydroxyapatite, HA, from bovine bones and continued with composite in nano clay powder .At the end a hydroxyapatite–clay (HA/Clay) nanocomposite ceramic, 80 wt.% of HA and 20 wt.% nano clay powder, was synthesized through a mechanical method , HEBM. The ability of apatite formation on the produced nanocomposite samples, as a yardstick for evaluation of the bioactivity, was estimated by using simulated body fluid. According to the results obtained mechanical and density values and bioactivity behavior, the sample containing 20 wt. % HA/Clay indicated the optimal properties in mechanical and bioactivity behavior. In fact, this nano composite sample, Ti-6Al-4V/20 HA-clay, is good candidate for medical purposes, bone tissue applications.

References:

[1]      Carole C, P., Physical Science And Technology Biotechnology, 2002.

[2]      Ning, C., and Zhou, Y., “Correlations between the in vitro and in vivo bioactivity of the Ti/HA composites fabricated by a powder metallurgy method”, Acta biomaterialia, vol. 4, no. 6, pp. 1944-1952, 2008.

[3]      Ajayan, P. M., Schadler, L. S., and Braun, P. V., Nanocomposite science and technology: John Wiley & Sons, 2006.

[4]      Ratner, B. D., Hoffman, A. S., Schoen, F. J., and Lemons, J. E., Biomaterials science: an introduction to materials in medicine: Academic press, 2004.

[5]      Fujii, E., Ohkubo, M., Tsuru, K., Hayakawa, S., Osaka, A., Kawabata, K., Bonhomme, C., and Babonneau, F., “Selective protein adsorption property and characterization of nano-crystalline zinc-containing hydroxyapatite”, Acta Biomaterialia, vol. 2, no. 1, pp. 69-74, 2006.

[6]      Pan, Y., and Xiong, D., “Friction properties of nano-hydroxyapatite reinforced poly (vinyl alcohol) gel composites as an articular cartilage”, Wear, vol. 266, no. 7, pp. 699-703, 2009.

[7]      Göller, G., Oktar, F. N., Toykan, D., and Kayali, E., "The improvement of titanium reinforced hydroxyapatite for biomedical applications." pp. 619-622.

[8]      Salman, S., Gunduz, O., Yilmaz, S., Öveçoğlu, M., Snyder, R. L., Agathopoulos, S., and Oktar, F., “Sintering effect on mechanical properties of composites of natural hydroxyapatites and titanium”, Ceramics International, vol. 35, no. 7, pp. 2965-2971, 2009.

[9]      Nakahira, A., and Eguchi, K., “Evaluation of microstructure and some properties of hydroxyapatite/Ti composites”, Journal of Ceramic Processing Research, vol. 2, no. 3, pp. 108-112, 2001.

[10]    Geetha, M., Singh, A., Asokamani, R., and Gogia, A., “Ti based biomaterials, the ultimate choice for orthopaedic implants–a review”, Progress in Materials Science, vol. 54, no. 3, pp. 397-425, 2009.

[11]    Black, J., and Hastings, G., Handbook of biomaterial properties: Springer Science & Business Media, 2013.

[12]    Katz, J. L., “Anisotropy of Young's modulus of bone”, 1980.

[13]    Sumner, D., Turner, T., Igloria, R., Urban, R., and Galante, J., “Functional adaptation and ingrowth of bone vary as a function of hip implant stiffness”, Journal of biomechanics, vol. 31, no. 10, pp. 909-917, 1998.

[14]    Livage, J., Henry, M., and Sanchez, C., “Sol-gel chemistry of transition metal oxides”, Progress in solid state chemistry, vol. 18, no. 4, pp. 259-341, 1988.

[15]    Salgado, A. J., Coutinho, O. P., and Reis, R. L., “Bone tissue engineering: state of the art and future trends”, Macromolecular bioscience, vol. 4, no. 8, pp. 743-765, 2004.

[16]    Klein, L. C., Sol-gel technology for thin films, fibers, preforms, electronics, and specialty shapes: William Andrew Publishing, 1988.