A

• Aghanajafi.Cyrus Numerical Analysis of Heat Transfer and Temperature Distribution in Direct Metal Laser Sintering Method [ Vol.14, Issue 4 - Autumn Year 2024]
• Ahmadi Balootaki.Mohammd Modal Analysis of Complex Structures via a Sub-Structuring Approach [ Vol.14, Issue 1 - Winter Year 2024]
• Ahmadi Balootaki.Mohammd Design an Adaptive Sliding Mode Controller for a Class of Underactuated Systems [ Vol.14, Issue 4 - Autumn Year 2024]
• Ahmadi.Afshin Numerical Study on Forced Convection of Slip Flow in A Microchannel with Smooth and Sinusoidal Walls [ Vol.14, Issue 4 - Autumn Year 2024]
• AhmadPour.M. Mechanical Buckling of Circular Orthotropic Bilayer Nanoplate Embedded in an Elastic Matrix under Radial Compressive Loading [ Vol.14, Issue 1 - Winter Year 2024]
• alavi fazel.seyed ali Development of A New Correlation for Estimating Pressure Gradient of Oil- Water Two Phase Flow in A Horizontal Pipe [ Vol.14, Issue 4 - Autumn Year 2024]
• Alian Moghadam.Hossein Investigation of the TiO2/SiC/SiO2 Coating Effect On the Wear Rate of Needle Graphite Electrode by using Electrical Discharge Machining [ Vol.14, Issue 2 - Spring Year 2024]
• Altan.Mirigül Topological Optimization of Brake Pedal for Metal Additive Manufacturing: A Case Study [ Vol.14, Issue 2 - Spring Year 2024]
• Amiri.Alireza Stress Wave Propagation in 2D Functionally Graded Media: Optimization of Materials Distribution [ Vol.14, Issue 2 - Spring Year 2024]
• Amraee Rad.Ghasem Design and Analysis of Metal-Composite Vessel under Internal Pressure [ Vol.14, Issue 4 - Autumn Year 2024]
• Arghavan.Alireza The Inverse Method of Damage Detection using Swarm Life Cycle Algorithm (SLCA) via Modal Parameters in Beam Like Structures [ Vol.14, Issue 2 - Spring Year 2024]
• Asgarikia.Mehdi Increasing the Fundamental Frequency of the Cantilever Rotating Beam by Placing the Intermediate Elastic Support with Minimum Stiffness at the Optimum Point Based on the Courant’s Maximum–Minimum Theorem using Finite-Element Analysis Software [ Vol.14, Issue 3 - Summer Year 2024]
• Ashouri.Hojjat Improving High Cycle Fatigue Life in A Gasoline Engine Piston using Oil Gallery with Considering Stress Gradient [ Vol.14, Issue 4 - Autumn Year 2024]
• Asiaban.Naser Bending and Buckling Analysis of a Nth-Order Shear Deformation Nanoplate using Modified Couple Stress Theory [ Vol.14, Issue 4 - Autumn Year 2024]
• Assareh.Ehsanolah Design and Optimization of Gasketed-Plate Heat Exchanger using Bees Algorithm [ Vol.14, Issue 3 - Summer Year 2024]
• Azarafza.Reza Dynamic Analysis of Carbon Nanotube-Reinforced Multilayer Composite Plates [ Vol.14, Issue 1 - Winter Year 2024]
• azimi.alireza Development of A New Correlation for Estimating Pressure Gradient of Oil- Water Two Phase Flow in A Horizontal Pipe [ Vol.14, Issue 4 - Autumn Year 2024]
• Azizi.Abdolhamid Evaluation of Fatigue Behavior and Surface Characteristics of Novel Machining Process: Rotary Chemical Machining (RCM) [ Vol.14, Issue 3 - Summer Year 2024]
• Azizi.Zoha Development of A New Correlation for Estimating Pressure Gradient of Oil- Water Two Phase Flow in A Horizontal Pipe [ Vol.14, Issue 4 - Autumn Year 2024]