-
المقاله
1 - مطالعه اثر میدان مغناطیسی بر زبری سطح قطعهکار در ماشینکاری تخلیه الکتریکی ماده مرکب آلومینیوم 413 تقویت شده با آلومینافرآیندهای نوین در مهندسی مواد , العدد 1 , السنة 17 , بهار 1402در این پژوهش، تأثیر پارامترهای ورودی ماشینکاری تخلیه الکتریکی بر روی زبری سطح قطعهکار از جنس ماده مرکب A413 تقویت شده با %5/2 Al2O3، در دو حالت با حضور میدان مغناطیسی و بدون وجود میدان مغناطیسی مورد بررسی و مقایسه قرار گرفته است. تحقیق ارائه شده با رویکرد طراحی آزمای أکثردر این پژوهش، تأثیر پارامترهای ورودی ماشینکاری تخلیه الکتریکی بر روی زبری سطح قطعهکار از جنس ماده مرکب A413 تقویت شده با %5/2 Al2O3، در دو حالت با حضور میدان مغناطیسی و بدون وجود میدان مغناطیسی مورد بررسی و مقایسه قرار گرفته است. تحقیق ارائه شده با رویکرد طراحی آزمایشات به روش تاگوچی بر مبنای آرایه متعامد L9 و تکنیک سطوح تکراری به انجام رسیده است. پارامترهای ورودی این آزمایشات شامل ولتاژ (دو سطحی)، شدتجریان (سه سطحی)، زمان روشنی پالس (سه سطحی) و زمان خاموشی پالس (سه سطحی) در نظر گرفته شده است. نتایج آزمایشات نشان دهنده کاهش زبری سطح ماشینکاری شده تا 32 درصد در حضور میدان مغناطیسی می باشد. تحلیل نتایج شامل تعیین نمودارهای نسبت سیگنال به نویز متناظر با هر یک از پارامترهای ورودی و آنالیز واریانس توسط نرمافزار Minitab صورت گرفته است. نتایج بدست آمده گویای بهبود کیفیت سطح قطعهکار در حضور میدان مغناطیسی در مقایسه با شرایط ماشینکاری بدون وجود میدان مغناطیسی است. همچنین برمبنای نتایج حاصل از آنالیز واریانس در هر دو حالت مذکور، شدت جریان مؤثرترین پارامتر ورودی بر روی زبری سطح قطعهکار از جنس ماده مرکب A413 تقویت شده با %5/2 Al2O3، تعیین شده است. تفاصيل المقالة -
المقاله
2 - Investigating on process variables effect of AISI 304 stainless steel machining using minimum quantity lubricant on cutting forceJournal of Simulation and Analysis of Novel Technologies in Mechanical Engineering , العدد 5 , السنة 14 , پاییز 2022In the machining process, the friction between the tool and the surface being machined, in addition to the destructive effects on tool wear and surface quality, increases the cutting force. By applying lubricant, it is possible to reduce the friction force in the machin أکثرIn the machining process, the friction between the tool and the surface being machined, in addition to the destructive effects on tool wear and surface quality, increases the cutting force. By applying lubricant, it is possible to reduce the friction force in the machining process, and as a result, the cutting force is reduced. Due to the harmful environmental effects of excessive use of lubricants, the method of minimum quantity lubricant (MQL) can be helpful. In this method, fluid is applied with controlled flow and pressure. In this research, the effect of machining conditions on the cutting force for the machining process of AISI 304 stainless steel, using the method of minimum quantity lubricant has been investigated. The results show that with the increase in the cutting speed, the cutting force has decreased. Also, with the increase of injection pressure when applying the lubricating fluid using the method of the minimum quantity lubricant, a significant increase in the cutting force has been observed. تفاصيل المقالة