A Comparative FEM Analysis of a Substituted 3D-Printed U-Joint with PLA and ABS Materials
الموضوعات :
Mohammad Sajjad Mahdieh
1
,
Golshid Fathinasab
2
1 - Mechanical Engineering Dep., Chamran University of Ahvaz, Ahvaz, Iran.
2 - Department of Mechanical Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
الکلمات المفتاحية: ABS, 3D-Printing, FEM Analysis, Machine Components, PLA ,
ملخص المقالة :
Currently, manufacturing and repairing industrial equipment in a short time with the least cost has been a challenge. Furthermore, the idle time of the industrial machines due to their failed parts imposes high losses on the production process. Applying 3D printers to manufacture damaged parts quickly is a promising measure to tackle the abovementioned problem. This article is an efficient approach to the manufacture and analysis of a universal joint (U-joint) as the case study with Polylactic acid (PLA) and Acrylonitrile butadiene styrene (ABS) through the 3D printing process. U-joints are widely used as a coupling in industrial equipment to alleviate the misalignment of input and output shafts in many gearboxes and pumps. Because of undergoing fatigue loads, the failure occurrence in U-joints is very probable. Therefore, an attempt is made here to substitute this part with a 3D-printed one. Besides, comparing and evaluating the results of FEM simulations for the sake of selecting the most suitable material for the U-joint are done. According to the FEM results, the maximum stress imposed on the U-joint was obtained 28.8MPa which is lower than the yield strength of both PLA and ABS materials; however, the results show that PLA has higher fatigue strength than ABS in this case.
[1] Kohli, A., et al., Analysis of Universal Joint Using Virtual Simulation Method, Materials Today: Proceedings, Vol. 59, 2022, pp. 858-866.
[2] Mahdieh, M. S., Rafati, E., and Kargar Sichani, S., Investigation of Variance of Roller Burnishing Parameters on Surface Quality by Taguchi Approach. ADMT Journal, Vol. 6, No. 3, 2013.
[3] Saraeian, P., et al., Influence of Vibratory Finishing Process by Incorporating Abrasive Ceramics and Glassy Materials on Surface Roughness of CK45 Steel. ADMT Journal, Vol. 9, No. 4, 2016, pp. 1-6.
[4] Vakili Sohrforozani, A., et al., A Study of Abrasive Media Effect on Deburring in Barrel Finishing Process. Journal of Modern Processes in Manufacturing and Production, Vol. 8, No. 3, 2019, pp. 27-39.
[5] Vakili Sohrforozani, A., et al., Effects of Abrasive Media on Surface Roughness in Barrel Finishing Process. ADMT Journal, Vol. 13, No. 3, 2020, pp. 75-82.
[6] Mahdieh, M. S., Zadeh, H. M. B., and Reisabadi, A. Z., Improving Surface Roughness in Barrel Finishing Process Using Supervised Machine Learning, Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, Vol. 15, No. 2, 2023, pp. 5-15.
[7] Ćwikła, G., et al. The Influence of Printing Parameters on Selected Mechanical Properties of FDM/FFF 3D-Printed Parts, In IOP Conference Series: Materials Science and Engineering, IOP Publishing, 2017.
[8] Kiendl, J., Gao, C., Controlling Toughness and Strength of FDM 3D-Printed PLA Components Through the Raster Layup, Composites Part B: Engineering, 2020, Vol. 180, pp. 107562.
[9] Goyanes, A., et al., Fabrication of Controlled-Release Budesonide Tablets via Desktop (FDM) 3D Printing, International Journal of Pharmaceutics, Vol. 496, No. 2, 2015, pp. 414-420.
[10] Popa, C. F., et al., Numerical and Experimental Study for FDM Printed Specimens from PLA under IZOD Impact Tests, Materials Today: Proceedings, Vol. 78, 2023, pp. 326-330.
[11] Mahdieh, M. S., Esteki, M. R., Feasibility Investigation of Hydroforming of Dental Drill Body by FEM Simulation. Journal of Modern Processes in Manufacturing and Production, Vol. 11, No. 2, 2022, pp. 71-83.
[12] Mahdieh, M. S., Monjezi, A., Investigation of an Innovative Cleaning Method for the Vertical Oil Storage Tank by FEM Simulation, Iranian Journal of Materials Forming, 2022.
[13] Mahdieh, M. S., et al., A Study on Stamping of Airliner’s Tail Connector Part through FEM Simulation, Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, 2023.
[14] Heidari-Rarani, M., Rafiee-Afarani, M., and Zahedi, A., Mechanical Characterization of FDM 3D Printing of Continuous Carbon Fiber Reinforced PLA Composites, Composites Part B: Engineering, Vol. 175, 2019, pp. 107147.
[15] Akhoundi, B., Behravesh, A. H., Effect of Filling Pattern on The Tensile and Flexural Mechanical Properties of FDM 3D Printed Products, Experimental Mechanics, Vol. 59, No. 6, 2019, pp. 883-897.
[16] Vijayaraghavan, V., et al., Process Characterisation of 3D-Printed FDM Components Using Improved Evolutionary Computational Approach, The International Journal of Advanced Manufacturing Technology, Vol. 78, No. 5, 2015, pp. 781-793.
[17] Deswal, S., Narang, R., and Chhabra, D., Modeling and Parametric Optimization of FDM 3D Printing Process Using Hybrid Techniques for Enhancing Dimensional Preciseness, International Journal on Interactive Design and Manufacturing (IJIDeM), Vol. 13, No. 3, 2019, pp. 1197-1214.
[18] San Andrés, M., et al., Use of 3D Printing PLA and ABS Materials for Fine Art, Analysis of Composition and Long-Term Behaviour of Raw Filament and Printed Parts, Journal of Cultural Heritage, Vol. 59, 2023, pp. 181-189.
[19] Karamimoghadam, M., et al., Influence of Post-Processing CO2 Laser Cutting and FFF 3D Printing Parameters on The Surface Morphology of PLAs: Statistical Modelling and RSM Optimisation, International Journal of Lightweight Materials and Manufacture, Vol. 6, No. 2, 2023, pp. 285-295.
[20] Martin, V., et al., Low-cost 3D Printing of Metals Using Filled Polymer Pellets, HardwareX, Vol. 11, 2022, pp. e00292.
[21] Mahdieh, M. S., The Surface Integrity of Ultra-Fine Grain Steel, Electrical Discharge Machined Using Iso-Pulse and Resistance–Capacitance-Type Generator. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Vol. 234, No. 4, 2020, pp. 564-573.
[22] Mahdieh, M. S., Recast Layer and Heat-Affected Zone Structure of Ultra-Fined Grained Low-Carbon Steel Machined by Electrical Discharge Machining. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 234, No. 5, 2020, pp. 933-944.
[23] Mahdieh, M. S., Mahdavinejad, R., Comparative Study on Electrical Discharge Machining of Ultrafine-Grain Al, Cu, and Steel, Metallurgical and Materials Transactions A, Vol. 74, No. 12, 2016, pp. 6237-6247.
[24] Mahdieh, M. S., Zare-Reisabadi, S., Effects of Electro-Discharge Machining Process on Ultra-Fined Grain Copper, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 233, No. 15, 2019, pp. 5341-5349.
[25] Mahdieh, M. S., Mahdavinejad, R. A., A Study of Stored Energy in Ultra-Fined Grained Aluminum Machined by Electrical Discharge Machining. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 231, No. 23, 2017, pp. 4470-4478.
[26] Mahdieh, M. S., Mahdavinejad, R., Recast Layer and Micro-Cracks in Electrical Discharge Machining of Ultra-Fine-Grained Aluminum. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 232, No. 3, 2018, pp. 428-437.
[27] Mahdieh, M. S., Improving Surface Integrity of Electrical Discharge Machined Ultra-Fined Grain Al-2017 by Applying RC-Type Generator, Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2023, pp. 09544089231202329.
