The Effect of using a Semi-Automatic Foam Cutting Machine on The Characteristics of Foam Patterns in The Lost Foam Casting
الموضوعات :
Sadegh Mirzamohammadi
1
,
Abbas Abbasian
2
,
Seyed Jalal Hashemi
3
1 - Department of Materials and Metallurgical Engineering, National University of Skills (NUS), Tehran, Iran
2 - Department of Materials and Metallurgical Engineering, National University of Skills (NUS), Tehran, Iran
3 - Department of Mechanical Engineering, National University of Skills (NUS), Tehran, Iran
الکلمات المفتاحية: Lost Foam Casting, Patterns, Precision, Semi-Automatic Foam Cutting,
ملخص المقالة :
In this research, a modern method for making foam patterns, which is one of the most important steps of casting with a lost foam pattern, has been used. A semi-automatic hot wire machine was built to cut and create foam patterns. Two types of foam patterns were prepared by manual method and cutting method with semi-automatic machine. The sizes of the obtained foam patterns were evaluated and the accuracy of each method in the production of foam patterns was compared. According to the density of the foam used in the experiments, the volume of the prepared patterns was obtained by manual and semi-automatic methods. The additional volume in the prepared patterns was calculated by both methods. The amount of economic losses caused by excess volumes was investigated. The results of the research determined that the accuracy of the sizes of the patterns prepared by the semi-automatic method was more than twice the accuracy of the patterns prepared by the manual method. The patterns prepared by the semi-automatic method had an additional volume of 1.9% compared to the volume of the original part. While the mentioned amount for foam patterns cut by the manual method was 9%. Therefore, the economic efficiency of casting parts using foam patterns made by semi-automatic method in terms of melting consumption for aluminum parts was 8% more than production parts using foam patterns made by manual method.
[1] Barone, M. R., Caulk, D. A., A Foam Ablation Model for Lost Foam Casting of Aluminum, International Journal of Heat and Mass Transfer, Vol. 48, No. 19–20, 2005, pp. 4132–4149, doi: 10.1016/j.ijheatmasstransfer.2005.03.031.
[2] Basso, A., Toda-Caraballo, I., San-Martín, D., and Caballero, F. G., Influence of Cast Part Size on Macro- and Microsegregation Patterns in A High Carbon High Silicon Steel, Journal of Materials Research and Technology, Vol. 9, No. 3, 2020, pp. 3013–3025, doi: 10.1016/j.jmrt.2020.01.052.
[3] Brown, J., Foseco Ferrous Foundryman’s Handbook. Elsevier Science, 2000.
[4] Chen, H. Z., Shan, Z. De, and Dong, H. Z., Research of Foam Pattern Processing for Lost Foam Casting, International Conference on Process Equipment, Mechatronics Engineering and Material Science, Vol. 331, 2013, pp. 600–603, doi: 10.4028/www.scientific.net/AMM.331.600.
[5] Guler, K. A., Acar, S., Lost Foam Casting of Metallic Parts and Structures, In F. G. Caballero (Ed.), Encyclopedia of Materials: Metals and Alloys, Elsevier, 2022, pp. 73–86, doi: 10.1016/B978-0-12-819726-4.00008-9.
[6] Guler, K. A., Kisasoz, A., and Karaaslan, A., Effects of Pattern Coating and Vacuum Assistance on Porosity of Aluminium Lost Foam Castings, Russian Journal of Non-Ferrous Metals, Vol. 55, No. 5, 2014. pp. 424–428. doi: 10.3103/S1067821214050113.
[7] Jafari, H., Idris, M. H., and Shayganpour, A., Evaluation of Significant Manufacturing Parameters in Lost Foam Casting of Thin-Wall Al-Si-Cu Alloy Using Full Factorial Design of Experiment, Transactions of Nonferrous Metals Society of China (English Edition), Vol. 23, No. 10, 2013, pp. 2843–2851, doi: 10.1016/S1003-6326(13)62805-8.
[8] Jiang, W., Fan, Z., Liao, D., Liu, D., Zhao, Z., and Dong, X., Investigation of Microstructures and Mechanical Properties of A356 Aluminum Alloy Produced by Expendable Pattern Shell Casting Process with Vacuum and Low Pressure, Materials and Design, Vol. 32, No. 2, 2011, pp. 926–934, doi: 10.1016/j.matdes.2010.08.015.
[9] Kannan, P., Biernacki, J. J., and Visco, D. P., A Review of Physical and Kinetic Models of Thermal Degradation of Expanded Polystyrene Foam and Their Application to The Lost Foam Casting Process, Journal of Analytical and Applied Pyrolysis, Vol. 78, No. 1, 2007, pp. 162–171, doi: 10.1016/j.jaap.2006.06.005.
[10] Karimian, M., Ourdjini, A., Hasbullah Idris, M., and Jafari, H., Effect of Pattern Coating Thickness on Characteristics of Lost Foam Al-Si-Cu Alloy Casting, Transactions of Nonferrous Metals Society of China (English Edition), Vol. 22, No. 9, 2012, pp. 2092–2097, doi: 10.1016/S1003-6326(11)61433-7.
[11] LI, J., Chen, R., and Ke, W., Microstructure and Mechanical Properties of Mg-Gd-Y-Zr Alloy Cast by Metal Mould and Lost Foam Casting, Transactions of Nonferrous Metals Society of China, Vol. 21, No. 4, 2011, pp. 761–766, doi; 10.1016/S1003-6326(11)60777-2.
[12] Liu, X. J., Overfelt, R. A., and Bhavnani, S. H., The Effects of Foam Density and Metal Velocity on The Heat and Mass Transfer in The Lost Foam Casting Process, Proceedings of the ASME Summer Heat Transfer Conference, 2003, pp. 317–323, doi: 10.1115/ht2003-47504.
[13] Nicoletto, G., Anzelotti, G., and Konečná, R., X-Ray Computed Tomography Vs, Metallography for Pore Sizing and Fatigue of Cast Al-Alloys, Procedia Engineering, Vol. 2, No. 1, 2010, pp. 547–554. doi: 10.1016/j.proeng.2010.03.059.
[14] Paramasivam, K., Vijay Anand, M., and Sambathkumar, M., Investigation of Optimum Process Parameter of Lost Foam Casting of A356/SiC Metal Matrix Composite, Materials Today: Proceedings, Vol. 47, 2021, pp. 4801–4806, doi: 10.1016/j.matpr.2021.06.035.
[15] Sands, M., Shivkumar, S., Influence of Coating Thickness and Sand Fineness on Mold Filling in The Lost Foam Casting Process, Journal of Materials Science, Vol. 38, No. 4, 2003, pp. 667–673, doi: 10.1023/A:1021859523363.
[16] Shayegh, J., Hossainpour, S., Rezaei, M., and Charchi, A., Developing a New 2D Model for Heat Transfer and Foam Degradation in EPS Lost Foam Casting (LFC) Process, International Communications in Heat and Mass Transfer, Vol. 37, No. 9, 2010, pp. 1396–1402, doi: 10.1016/j.icheatmasstransfer.2010.07.015
[17] Sun, D., An Overview of Lost Foam Casting Technology Development in China. AFS Transactions, American Foundry Society, Vol. 08–035, No. 14, 2008, pp. 1–8.
[18] Wang, L., Limodin, N., El Bartali, A., Witz, J. F., Seghir, R., Buffiere, J. Y., and Charkaluk, E., Influence of Pores on Crack Initiation in Monotonic Tensile and Cyclic Loadings in Lost Foam Casting A319 Alloy by Using 3D In-Situ Analysis, Materials Science and Engineering: A, Vol. 673, 2016, pp. 362–372, doi: 10.1016/j.msea.2016.07.036.
[19] Xiao, B., Fan, Z., Jiang, W., Liu, X., Long, W., and Hu, Q., Microstructure and Mechanical Properties of Ductile Cast Iron in Lost Foam Casting with Vibration, Journal of Iron and Steel Research, International, Vol. 21, No. 11, 2014, pp. 1049–1054, doi: 10.1016/S1006-706X(14)60182-5.
[20] Zhao, Z., Fan, Z. T., Jiang, W. M., and Dong, X. P., Microstructural Evolution of Mg9AlZnY Alloy with Vibration in Lost Foam Casting During Semi-Solid Isothermal Heat Treatment, Transactions of Nonferrous Metals Society of China (English Edition), Vol. 20, No. 3, 2010, pp. 768–773, doi: 10.1016/S1003-6326(10)60579-1.
